VICOUSTIC Multifuser DC3 2′ x 2′ Acoustic Diffuser Instruction Manual

June 9, 2024
VICOUSTIC

VICOUSTIC-LKOGO

VICOUSTIC Multifuser DC3 2′ x 2′ Acoustic Diffuser

INSTRUCTION

MATERIAL NEEDED

  • Included

Multifuser DC3

  • Silicone Drop
  • VicFix Mini

Not Included

  • 6mm Phillips Screwdriver

  • Measuring Tape

  • Wall Plugs and Screws

  • Level

  • Drill

  • Flexi Glue Ultra

This product can be installed on the wall with VicFix Mini and on the ceiling using Flexi Glue Ultra (not supplied).VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-6

  • Wall Installation
  • Ceiling Installation
Ways of using the gauge

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-7 VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-8

Wall installation – One panel
After defining the place where you want to install the panels, start marking the position of the Multifuser DC3 fixation clips.

WARNING: This product can also be installed using Flexi Glue Ultra.

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-9

Wall installation – Installation up to three panels
Define the place where you want to install the panels and fix the First VicFix Mini. From there and with the help of the gauge provided, mark the positioning of the remaining fixation clips.

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-10VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-11 VICOUSTIC-
Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-FIG-12

To install the last Multifuser DC3, use it to mark the inner side of the last fixing clip. Remove the last two panels again and use the gauge provided to ensure the clips are aligned. Fix the last clip. You can use a bubble level to help in this procedure.

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-13VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-14 VICOUSTIC-
Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-FIG-15 VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-16

Install the last two panels.

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-17 VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-18

Wall Installation – Vertical Installation
Install the first panel according to step number 2. Follow the steps described in the following diagrams.

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-19VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-20

Ceilling Installtion

VICOUSTIC-Multifuser-DC3-2'-x-2'-Acoustic-Diffuser-
FIG-21VICOUSTIC-Multifuser-DC3-2'-x-2
'-Acoustic-Diffuser-FIG-22

WARNING: To ensure that you maximise the strength of the glue, don’t make any adjustments to the panel after bonding.

Wall and ceilling surfaces should be examined prior to installation, ensuring they are clean, smooth, and dry. If you have unpainted gypsum board surfaces, these should be primed with a drywall primer (or another material manufactured especially for the purpose), to equalize the absorption between the gypsum board face paper, joint compound, and skin coating materials. You should then apply the paint, and allow air circulation in order to dry the paint within the time frame specified by the paint manufacturer. Please ensure the paint is dry before installing the acoustic panel. Make sure the room has all the necessary conditions to receive the acoustic panels. After you apply the glue on the back of each acoustic panel, please ensure you hold the acoustic panel against the wall the required time (mentioned above), and ensure it stays fixed in place. This method is also applicable to ceiling installations.

Main Office, R &D & Logistics

  • ADDRESS: Avenida do Pólo 3, Nº 159, Carvalhosa 4590-137 Paços de Ferreira, Portugal
  • Office: Rua Quinta do Bom Retiro Nº 16, Armazém 9 2820-690 Charneca da Caparica, Portugal
  • T: (+351) 212 964 100

Info and Sales

© Vicoustic, 2021 | V3
No parts of this document might be copied and/or published without written consent of Vicoustic.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals