iTECHWORLD iTECH500P Portable Power Station User Guide

: June 5, 2024
: iTECHWORLD

iTECH500P
Portable Power Station
USER GUIDE

iTECHWORLD iTECH500P Portable Power Station

Before using or storing, please read this user guide carefully, and charge your iTECH500P with the included charging adapter

Introduction

Thank you very much for purchasing our multi-function portable power station. In case of power failure or you need to charge on a travel, you can temporarily charge your electrical or digital products with this product. This power station is built with high quality lithium-ion battery, supports USB, DC 12V and AC output. Before using this product, please read the user manual carefully and properly keep for reference.

What’s In The Box

A: iTECH500P Portable Power Station
B: AC Charging Adapter
C: Car Charger Cable
D: User Guide

A B

C D

Get To Know iTECH500P

iTECHWORLD iTECH500P Get To Know iTECH500P

A. Main Power Button
B. AC Output
C. USB-A QC Output
D. USB-C PD Input/ Output
E. USB-A Output
F. 12V Output
G. LCD Display
H. DC Input Port
I. Solar Charging Port

LCD Display

iTECHWORLD iTECH500P LCDDisplay

INPUT: shows the amount of power (watts) going into the iTECH500P while charging.

OUTPUT: shows the amount of power (watts) your devices are using while plugged into the iTECH500P.

BATTERY LEVEL: shows 10 segments, approximating 10% – 20% – 30% – 40% – 50% – 60% – 70% – 80% – 90% – 100% capacity. When charging your iTECH500P you will notice a battery segment blinking, this indicates the current charge status. Once fully charged, all battery segments will be lit and remain solid.

OVERLOAD WARNING: power draw exceeds port’s maximum allowance, indicated by red light on the port’s button.

TEMPERATURE WARNING: the unit is over-heating.

Charging Your iTECH500P

iTECHWORLD iTECH500P Charging Your iTECH500P A

Charging from wall charger:

Using the included AC charging adapter, plug your iTECH500P into any wall outlet. You will know the iTECH500P is fully charged when the LCD display shows 100%.

Charging from solar panel:

The DC input and PV port are compatible with charging from solar panels.

Place your solar panel where it will get as much direct sunlight as possible
Solar charge times depend on weather conditions.
No solar regulator is required as the iTECH500P has a built in regulator.

IMPORTANT NOTE: When solar recharging your iTECH500P, take note of the voltages of the solar panels. Individual solar panels, or solar panels chained in series in excess of 24V(DC Input port) or 26V(PV port) cannot be used with the iTECH500P and can cause serious damage to the unit.

Charging from your car:

Although not recommended because of slow charge times, you can charge your iTECH500P from any 12V source, like your car.

Using Your iTECH500P

What it powers

… and many more

Light Phone Laptop Mini Fridge

How to use iTECH500P:

Press and hold the Main Power Button for 2 seconds, the power station will be turned on.
Press and hold the AC Button for 2 seconds to turn on/ off AC output port.
Press the 12V/ USB Button to turn on/ off the corresponding output port.
You’ll know the output port is turned on when the green LED light on the button is illuminated.
Press the DISPLAY Button turn on/ off the LCD display.
When not using certain ports, make sure to turn them off to conserve power.

Best-use strategy:

When charging device with your iTECH500P, take note of the LCD Battery Display. Make sure that the electronic device you are powering works properly prior to use. The max. power consumption for electronic devices is 500W.
If you plug in devices that have a high power requirement (a large refrigerator etc.), the charge level of your iTECH500P can drop very quickly and you may not get exactly 505Wh of energy. Also, especially when using the AC power output, the iTECH500P will be converting the energy from the DC power of the battery to the AC power needed by your device. Although iTECH500P has a highly efficient inverter, there is still some energy lost in the conversion and you will not get the full rated capacity of the battery.

Appropriate temperature usage:

Cold temperatures can impact both the battery capacity and the output power. The iTECH500P can power your devices at temperatures ranging from 14°F~104°F (-10°C~40°C). If your working temperature is beyond this range, the iTECH500P may stop working.

Technical Specifications

Battery

Cell Type: Li-ion NMC
Battery Capacity: 505Wh(140.4Ah@3.6V)
Lifecycles: 500 cycles to 80% capacity
Shelf-life: Charge every 3-6 months
Management System: PWM charge controller, BMS

Ports

AC Output Port: 230V, 50Hz (500W, 750W surge)
12V DC 5.5mm Port(output): 12V/ 5A, 60W max
12V Car Port(output): 12V/ 10A, 120W max
USB-A Ports(output): 5V/ 3.1A
USB-A QC Port(output): 5-9V, 18W max
USB-C PD Port(input/ output): 5-20V, 45W max
DC Charging Port(5.5mm, input): 11-24V, 72W max
Solar Charging Port(PV, input): 11-26V, 120W max

General

Weight: 5.8kg
Dimension: 300200192.6mm
Operating Temp.: -10°C~40°C
Charging Temp.: 0°C-40°C
Warranty: 12 months

Troubleshooting

If your devices are not recharging from iTECH500P, follow these steps:

1. Ensure the output port has been turned on. The green LED light on the power button should be lit up.
2. Check the Battery Display. If it is at 20% or below, charge it.
3. Verify your device is suitable for use with the iTECH500P:
a. All of the output ports have their own max power capacity. Check the Tech Specs to ensure your device is compatible.
3. Check the LCD Display for warning icons:

OVERLOAD WARNING: Power draw exceeds port’ s maximum allowance, indicated by red light in the port’s button. You need to remove the device in corresponding port first, and then press the button of the port to recover.
TEMPERATURE WARNING: The power station gets over-heating, allow it to cool, and then press the Main Power button to recover.

Frequently Asked Questions

What type of battery is in a iTECH500P?
The iTECH500P contains a lithium ion battery.

Can I charge iTECH500P while supplying power at the same time?
When iTECH500P is in recharging, the USB and DC 12V output ports are workable; but the AC output is shut down at this period.

Can I take my iTECH500P on a plane?
No, you can’t. iTECH500P contains a large number of lithium-ion batteries with a capacity considered to be hazardous by airlines.

How do I know if my device will work with the iTECH500P?
You’ll need to determine the amount of power your device requires. This may require some research on your end, a good internet search or examining the user guide for your device should suffice. To be compatible with the iTECH500P, you should use devices that require less than 500W.

Security And Maintenance

Do not short-circuit the unit. To avoid short-circuiting, keep the unit away from all metal objects (e.g. coins, hair-pins, keys, etc.).
Do not heat the unit, or dispose of it in fire, water or other liquids. Keep away from high temperatures. Do not expose the unit to direct sunlight.
Keep away from high humidity, dusty places.
Do not disassemble or reassemble this unit.
Do not drop, place heavy objects on, or allow strong impact to this unit.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not cover the device with towels, clothing and other item.
Use the unit properly to avoid electronic shock.
Please deal with scrap products in accordance with the regulations, do not treat the built-in battery as a household garbage, so as not to cause the explosion and pollution.
The product is only used for emergency power station, it can not replace the standard DC or AC power of household appliances or digital products.