VICOUSTIC VicStrip Wall Tiles Instruction Manual
- June 10, 2024
- VICOUSTIC
Table of Contents
VICOUSTIC VicStrip Wall Tiles
Product Information
VicStrip
VicStrip is an acoustic panel that can be installed on various types of walls for sound insulation.
Materials Included
- VicStrip Screws
Materials Not Included
- Screwdriver
- Circular saw
- Level
- Flexi Glue Ultra
- Hole saw
- Box cutter
- Measuring Tape
Before Installation
- Measure the wall where the panels will be applied.
- If necessary, make the necessary cuts to ensure proper installation.
- The following cuts can be done:
- Longitudinal cut following the PET grove with a box cutter.
- Longitudinal cut on the laminated area with a circular saw with ~ 60-Tooth blade.
- Transversal cut with a circular saw with ~ 60-Tooth blade.
- Round hole with a hole saw.
Wall Installation with Screws
- For application to plasterboard walls or wooden structures, install the VicStrip with the screws provided. Insert them into the panel grooves and attach them to the supporting wall or wooden structure.
- Repeat the process until all panels are installed.
Wall Installation with Glue
- For application on masonry or concrete walls, it is recommended to apply glue (not included).
- Apply the glue on the back of the acoustic panel, according to the diagram.
- Place the panel on the suitably chosen position on the wall. Once in the desired place, press it firmly against the wall.
- To ensure that you maximize the strength of the glue, do not make any adjustments to the panel after bonding.
- Repeat the process until all panels are installed.
MATERIAL NEEDED
Installation Instructions
-
Before installing the panels, measure the wall where you are going to apply them. If necessary, make the necessary cuts to ensure a proper installation.
The cuts can be done as indicated below.
-
Longitudinal cut folowing the PET grove, with the help of a box cutter.
-
Longitudinal cut on the laminated area, with the help of a circular, saw with ~ 60-Tooth blade.
-
Transversal cut with the help of a circular saw with ~ 60-Tooth blade.
-
Round hole with the help of a hole saw.
-
Wall installation with screws – For application to plasterboard walls or wooden structures, install the VicStrip with the screws provided, inserting them into the panel grooves and attaching them to the supporting wall or wooden structure.
-
Wall installation with glue – For application on masonry or concrete walls, it is recommended to apply glue (not included).
-
Apply the glue on the back of the acoustic panel, according to the diagram. Place the panel on the suitably chosen position on the wall. Once in the desired place, press it firmly against the wall.
-
To ensure that you maximize the strength of the glue, don’t make any adjustments to the panel after bonding.
-
Wall and ceilling surfaces should be examined before installation, ensuring they are clean, smooth, and dry. If you have unpainted gypsum board surfaces, these should be primed with a drywall primer (or another material manufactured especially for the purpose), to equalize the absorption between the gypsum board face paper, joint compound, and skin coating materials.
-
You should then apply the paint, and allow air circulation in order to dry the paint within the time frame specified by the paint manufacturer. Please ensure the paint is dry before installing the panel. Make sure the room has all the necessary conditions to receive the panels.
-
Main Office, R&D & Logistics
-
Avenida do Pólo 3, Nº 159, Carvalhosa
-
4590-137 Paços de Ferreira, Portugal
-
Office
-
Rua Quinta do Bom Retiro Nº 16, Armazém 9
-
2820-690 Charneca da Caparica, Portugal
-
T (+351) 212 964 100
-
Info and Sales
-
Vicoustic, 2022 | V5
-
No parts of this document might be copied and/or published without the written consent of Vicoustic.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>