SOUNDPEATS Mini Pro Active Noise Cancelling Wireless Earbuds User Guide
- June 9, 2024
- SoundPEATS
Table of Contents
Mini Pro Active Noise Cancelling Wireless Earbuds
User Guide
First Start
Open the charging case lid and
take out both earbuds, then remove the insulating film and put them back.
- The earbuds automatically pair to each other after being taken out from the charging case. LED indicator on main earbud flashes in red and white, the second earbud stays in white.
- Activate Bluetooth on the device, and choose “SOUNDPEATS Mini Pro HS” on Bluetooth list to pair.
ANC Mode
Press and hold the left MFB for 1.5 second, switch from Normal mode/ ANC ON/ Pass through mode.
Reset
- Clear the pairing record from your device.
- Place back both earbuds into charging case and make sure they are in charging status.
- Press and hold both buttons for l0s until both LEDs flash in red and white twice, reset complete.
Product Diagram
Wearing
Touch Control
Power On| Auto: Open up the case lid and take out the earbuds Manually: Press
and hold the MFB for 1.5s
---|---
Power Off| Auto: Place back the earbuds Manually: Press and hold the MFB for
lOs
Play / Pause| Double tap the MFB
Volume –| Single tap the left MFB
Volume +| Single tap the right MFB
Next Track| Press and hold right MFB for 1.5s
Answer / Hang Up Phone Call| Double tap the MFB
Reject Phone Call| Press and hold the MFB for 1.5s
Switch Between Two Calls| Press and hold the MFB for 2s
Manually Enter Palling Mode| Press and hold the MFB for 6s
Activate Vote Assistant| Triple tap the right MFB
Enter/Exit Game Mode| Triple tap the left MFB
Normal Mode/ ANC Mode/ Transparency Mode| Press and hold left MFB for 1.5s
Q&A
Al: What does the LED of earbuds mean?
– The LED indicators of earbuds stay red when it is in charging, disappear when fully charged.
Q2: What does the LED on the charging case tell?
| Green | 100%-50% |
|---|---|
| Yellow | 49%-10% |
| Red | Less than 10% |
When charging the charging case the LED flashes slowly.
| Red | Less than 20% |
|---|---|
| Yellow | 20%-69% |
| Green | 70%-99% |
| Stays in Green | 100% |
Q3: How to charge the case?
- Use a Type-C adapter to charge the case (current not over 1A).
- Please charge the earbuds and case at least once per 3 months when not in use for a long time.
Q4: Why are the earbuds still connected to my phone after placing back?
- The charging case Is out of battery. The case will not turn off the earbuds if the case battery is dead.
- Please make sure the earbuds sit well in the charging case, and the charging contactors on both the earbuds and charging case are clean.
Please try something like microfiber cloth to clean the contactors.
Q5: The battery life is not as advertised?
A single charge will not give you 28 hours playtime constantly. The earbuds work around 8 hours per charge with normal mode, 6 hours per charge with ANC mode. The charging case provides another 2.5 recharges.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
IC ID
- English: ” This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference thatmay cause undesired operation of the device.”
RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road, Longhua District
Shenzhen, China. 518109
support@soundpeats.com
www.soundpeats.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>