ikan PT4500-PEDESTAL 15 Inch Teleprompter User Guide

June 9, 2024
ikan

PT4500-PEDESTAL
15″ Teleprompter, Pedestal & Dolly Turnkey
Quick Start Guide

OVERVIEW

Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera setup. This solution includes a 15″ teleprompter, pedestal, and dolly. All of our systems have been tested internally for payload compatibility.
The remaining payload capacity, after mounting the full 15″ teleprompter system without the counterweight, can accommodate camera setups up to 17 lbs. The pedestal, without the teleprompter system, can accommodate cameras up to 35.8 lbs. This solution also includes a hard case for the teleprompter & carrying bag for the pedestal.

PT4500
15″ High Bright Beam Splitter Teleprompter

What’s Included

  • 1 x Teleprompter Base
  • 1 x Bracket with Glass
  • 1 x Teleprompter Hood with Boot
  • 1 x Monitor
  • 1 x AC Adapter with Cord
  • 1 x PrompterPro Software
  • 1 x Counterweight Set (2 x 2.5 lbs)
  • 2 x D-Ring ¼-20” Screws
  • 2 x Hex Keys
  • 3 x Different Height Risers

Teleprompter Assmebly Setup

Step 1
Place the teleprompter glass frame on a flat surface and remove the four screws as shown.|
---|---
Step 2
Align and attach the teleprompter hood with the 8 screw pegs from the teleprompter frame.|
Step 3
The metal frame is directional. Make sure the thicker side is on top and the slimmer side is on the bottom.|
Step 4
Put the washers on before tightening the screws. The washers and 4
additional screws are inside a bag on the bottom foam.|
Step 5
Extend the teleprompter hood open and attach teleprompter boot
using the clips. It is suggested to align the seam with the bottom of
the teleprompter hood.|
Step 6
Remove the monitor mounts from the teleprompter base using the included
larger 4mm hex key to loosen from the 15mm rods.|
Step 7
Attach the monitor mounts on the back of the monitor’s VESA compatible threads using the 4 included screws and provided 2mm hex key.|
Step 8
After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket.
Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.
SAFETY NOTE Make sure to leave at least 2 inches of the rods inside the teleprompter base.|
Step 9
While sliding the teleprompter bracket into the slot of the teleprompter base pull on the red knob to allow the bracket to fully slide in.|
Step 10
Once the bracket is in place, tighten the side screw to lock in place. Double check and make sure all the screws are tightened with the included hex keys.|

Step 11 (optional)
Should the teleprompter be too front heavy, you can attach the included counter weight on the back of the teleprompter base.

Foam Case

To make your teleprompter more portable, we packed it in a reusable, high- quality foam.
The shape and size of the foam was designed to fit into Ikan’s PT-CASE-V2.

DO NOT THROW AWAY FOAM CASE

Monitor Ports

BNC – AV Composite Input
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v Input

HDMI – Switch HDMI input
VGA – Switch to VGA input
AV – Switch to composite BNC input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting

Monitor Menu Settings

Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB Return

System Config
Menu Duration – Set duration of how long menu stays on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset Return

PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position Return Exit

How to set-up FLIP button feature:

  1. Press MENU button
  2. Navigate to SYSTEM CONFIG.
  3. Navigate to FLIP-V or FLIP-H
  4. Change FLIP-V and/or FLIP-H to “ON”
  5. Exit MENU
  6. The FLIP button should now be activated and can be pressed to mirror the image Horizontally or Vertically
  7. When FLIP-H is ON, the image will flip Horizontally
  8. When FLIP-V is ON, the image will flip Vertically
  9. If both are ON, the FLIP button will toggle both Horizontal and Vertical flip

Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Telepromopters:

https://youtu.be/5TjIxzBc_Vc

Specifications

PT4500

Aspect Ratio 4:03
Backlight LED
Brightness 1000 nits
Build Material Aluminum
Diagonal 15”
Input Signal Composite BNC, VGA, HDMI
Input Voltage DC 12v / 4A
Power Consumption 10W
Reading Range 17’
Resolution 1920 x 1080
Viewing Angle 160° (H) / 170° (V)
Weight 22 lb
Shipping Weight 28 lb
Shipping Dimensions 25 x 20 x 15.5 in

Optional Accessories

PT4500-G Replacement Glass for both PT4500 / PT4700
PT15-HB-V2 15” High Bright Monitor (for PT4500)
PT17-HB-V2 17” High Bright Monitor (for PT4700)
PT-CASE-V2 Rolling Hard Case for PT4500/PT4700 Teleprompter

Learn More

More dynamic information at official website: www.ikancorp.com

Support

Contact email: support@ikancorp.com

CONDITIONS OF WARRANTY SERVICE

  • Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
  • The components and maintenance service fee will be charged if the warranty period is expired.

*Free Service will not be Provided in the Following Situations:(Even if the product is still within the warranty period.)**

  • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
  • Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

©2021 Ikan International. All rights reserved.
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com

AT7903 Pedestal

GH20 100mm Fluid Head

FEATURES

SPECIFICATIONS

| Model| GH20
---|---|---
| Payload Range| 20.0kg  / 44.0lbs
| Counterbalance Range| 0-8
| Grades Of Pan Drag| Fixed
| Grades Of Tilt Drag| Fixed
| Tilt Range| -60°/+90°
| Temperature Range| -30℃~+60℃
| Bowl Size| 100mm
| Net Weight| 3.5kg / 7.7lbs

El-7004B video Dolly
Super sturdy, designed for heavy duty systems. The 100mm/4 inch wheels can be individually braked.

FEATURES

| |
---|---|---
Pull the knob to extend the dolly, easy to go out.| Height : 17cm / 6.7in
Radius: 50cm / 19.7in| Casters diameter: 100mm / 3.9in.
| |
The rubber wheels are non-marring during normal use, protecting the floor surface.
Each wheel incorporates its own foot-activated brake.| Cable guards and brakes.| Supports up to 60kg of tripod,
Camera and accessories.

GB3 Pan bar
Telescopic pan bar for GH08L, GH10L, GH15, GH25 heads

SPECIFICATIONS

| Length range| 405-605mm / 15.9-23.8in
---|---|---
| Net weight| 385g / 0.8lbs

www.eimagevideo.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ikan User Manuals

Related Manuals