NIT SINE MZ-FRGB45A LED Photography Light Instruction Manual

NIT SINE MZ-FRGB45A LED Photography Light

Please carefully read the instruction before you use the product and keep it after your review so that you can refer to it in later days.

WARNINGS

1. Please keep it dry. Do not touch the product with wet hands. Do not immerse the product in water or expose to rain.
2. Non-waterproof, please pay attention to moist in rainy days and wet conditions.
3. Keep out of reach of children.
4. Prohibit dismantling, striking, crushing or exposing to fire.
5. Do not use in the presence of flammable gases, otherwise may cause an ooster or fire.
6. Do not use or store the product in a closed space under high temperature or direct sunlight.
7. Please Use the matching power adapter or the corresponding specifications of the lithium battery to power the product, do not use the non-original power adapter with different output voltage parameters.
8. When not in use, unplug the power cord or remove the external battery.

PRODUCT SPECIFICATION

Ambient Temperature

|  10 to 40 degrees, the storage temperature is to 4 degrees
Power input interface| DC
Product Dimension| 2 8mm203mm40mm
Net Weight| about 1200g
LED| 288P S
Maximum Illuminance| 7000lux 0. m, 2200lux 1m
Control method| APP
RGB Color Gamut| 0 360° full

PARTS NAME

INSTALLATION

1. Turn the knob clockwise to mount the light on the bracket and counter clockwise fo remove it.
2. Open the light baffle from the side of the light panel.
3. Loosen the adjusting knobs on both sides of the U-bracket to adjust the angle of the panel you need.Then tighten the adjustment knobs on both sides of the U-bracket.
4. Two power supply modes:
5. Connect the power cord and adapter for power supply.
6. Purchase two other suitable lithium batteries and use the batteries.

Note:

1. Both battery slots must be inserted into the battery to supply power.
2. Device does not include batteries, additional purchase required.

ACCESSORY INSTALLATION GUIDE

Only some of the sets contain the following accessories, subject to the actual purchase of the set

1. LIGHT CONTROL FOLD: THE LIGHT CONTROL FOLD CONTROLS THE ANGLE OF THE LIGHT.
2. DAign the front mounting holes with the screw holes in the fold.
3. Use the screws to lock the latch.

PRODUCT CONTROL KEYS GUIDE

1. DC15V power input connector
2. Power switch
3. Music mode button
4. Mode switch button: Switch the control mode
5. Brightness adjustment knob: Rotate this knob to adjust the brightness
6. Bluetooth reset: Press 3 and 4 at the same time to enter Bluetooth reset pairing.
7. LCD screen: Display curent light parameters, control mode, channel value, scene serial number, etc.

FEATURES & INSTRUCTIONS

LCD DISPLAY
LCD display shows the cuTrent brightness of the light, control mode, light mode, light parameters, scene number, music rhythm, battery power, remote control channel (not open)

MODEL TYPES AND FUNCTIONS

Adjust the CCT
Short press the mode key, select the CCT mode, rotate the adjustment knob can adjust the bright 1%-100%. Short press the knob key, the current light selection color temperature adjustment, rotate the adjustment knob can adjust the color temperature 320OK-5600K.

Adjust the RGB
Short press the mode key, select RGB mode, rotate the adjustment knob can adjust the RGB color purity 0%-100%, respectively. Short press the knob key can adjust the upper and lower RGB color purity respectively for selection.

Adjust the HSI
Short press the mode key, select the HSI mode, rotate the adjustment knob can adjust the H hue 0-360° short press the knob key. the curent light selection S saturation can be adjusted 0%-100%; short pres the knob key, the current ight selection I brightness adjustable 10%-100%.

• Color temperature (CCT): Adjustable light temperature, range 3200K5600K
• Hue (HUE): Adjustable light color, range 0°-360
• Color purity (SAT): Adjustable light color saturation, range 0%-100%
• Scene (SCN): Simulate 15 kinds of scenes of light, shot press the mode button, select SCN mode.
  In the default mode, the light’s rotary adjustment knob can adjust the interval time of different scenes.
  Short press the knob key fo select the scene brightness 1o-100%6; short press the
  knob key, the curentlight to select the scene effects 1-15: effects are as follows:

1. Lightning – with voice-activated mode
2. Fade – with voice-activated mode
3. Strobe – with voice-activated mode
4. Fire – with sound control mode
5.  Jump (party mode) – with sound control mode
6. Breath – with sound mode
7. Sunrise
8. Paparazzi
9. Bad Bulb
10. Movie
11. Police Light – fixed speed
12. Ambulance- fixed speed
13. Fire truck – fixed speed
14. Mayday – fixed speed
15. Fireworks

ADJUSTMENT SCENES (SCM): RANGE 1-15

Mode switch key into the SCM mode, short press the brightness adjustment knob for 3 seconds to enter the mode adjustment, all scenes can be selected by rotating the brightness adjustment knob; When the Curent scene is No. 1 scene (lightning mode), rotate the compound knob to adiust to No. 2 scene (aradient model.

APP CONTROL

NOTE: Bluefooth reset is required before pairing, press 3 and 4 af the same time to enter Bluetooth reset pairing.

1. Scan the QR code on the back of the manual fo download the APP.Down- load tuya Smart APP, complete the account registrafion and login, turn on your phone Bluetooth and enter tuya Smart APP home page.
2. Open the fop right corner”+”and add device, APP will automatically enter fhe device search and connect the Bluetooth of the camera light through the phone, click add after finding the device
3. The device AUTOMATICALLY enter the add process, click next after adding, and name the device, click finish.
4. After adding, you can adjust the color temperature, full color RGB, and rightness of the camera light through the APP.

STEPS TO ADD APP

Step 1: Click “+” and select Add Device

Step 2: Wait for Bluetooth fo search and discover the device by itself Click “Add” and wait

Step 3: Wait for the prompt. “Added successfully”

Step 4 : Click “Done” to enter APP operation interface

APP INTERFACE OPERATION

APP GROUP CONTROL

Step 1: Prepare two or more camera lights and connect the cell phone APP.

Step 2 : Click on any of thE bulbs to enter the settings interface

Step 3: Click on “Edit” in the upper right corner

Step 4: Select “Create Group”

Step 5 : Select”+ to add a group.
Step 6 : Set group name
Step 7 :Click “Done” to enter the APP operation interface

USE AND STORAGE

Do not expose the product to high humidity, strong electromagnetic fields, direct sunlight, or high temperatures. If the product is not used for a long time, please disconnect the power and remove the battery.

Cleaning: Before cleaning, unplug the power supply. and use a damp cloth instead of any cleaning agent or soluble soluble liquid to avoid damaging the surface layer.

Power supply: Ensure that the power supply is within the required range for Use, too high or too low will affect the work. Load When loading the battery. do not install the battery backwards, otherwise it will damage the machine.

Repair: In case of malfunction or performance degradation, please do not open the housing package by yourself to avoid damaging the machine. Please feel free fa contacf us, we will do our best fo solve the problem.

Accessories: Please Use manufacturer supplied accessories or approved accessory products for best performance.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

caution: Any changes or modifications to this device not explicitily approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>