beamZ SNOW5000 High Volume Snow Machine User Manual

beamZ SNOW5000 High Volume Snow Machine

SAFETY INSTRUCTIONS

**WARNING!

**

Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference. It contains important information about the installation, usage and maintenance of the unit.

• Unpack and check carefully that there is no transportation damage before using the unit.
• Please read these instructions carefully and follow the instructions.
• Observe all safety warnings. Never remove safety warnings or other information from the equipment.
• Be sure that no ventilation slots are blocked; otherwise, the unit will overheat.

WARNING
Before connecting the equipment to the power outlet, first, verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the main power values match. If the included power cord or the power adapter does not fit in your wall outlet, contact your electrician.

• After connecting the unit, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
• Make sure that the power cord is never crimped or damaged. Check the unit and the power cord from time to time.
• Always disconnect power from the mains, when unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
• Do not switch the unit on and off in short intervals.
• Do not connect the unit to a dimmer pack.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• This unit is not designed for permanent operation. Consistent operation breaks will ensure that the unit will serve you for a long time without defects.
• Thus never aim at persons or animals directly and keep a minimum distance of 3 m (9.8 ft) to the nozzle.
• The location for the unit must be non-flammable, non-combustible and not sensitive to heat.
• Keep a minimum distance of 1 meter (3.28 ft) to all flammable, combustible objects and objects sensitive to heat.
• Never point the snow at strong sources of ignition like fire or pyrotechnic effects.
• Do not swallow the fluid. In case of eye contact, rinse with a lot of water. Consult a doctor should you have accidentally swallowed some fluid.
• Spilled fluid or splashed fluid droplets can cause slip hazards. Mop up the fluid and dispose of it according to regulations.

WARNING
If the power cord of the unit is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

• Make sure that the unit is not exposed to extreme heat, moisture or dust.
• Clean the unit using a dry cloth.
• Do not touch the unit bare-handed during its operation (housing becomes very hot). After switching off, the unit can remain warm for a few hours.
• This unit is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of fluid (does not apply to special outdoor equipment – in this case, observe the special instructions noted below). Do not expose this unit to flammable materials, fluids or gases.
• If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.
• Never attempt to bypass the thermostatic switch or fuses.
• Do not dismantle or modify the unit.
• For replacement use fuses/bulbs of the same type and rating only.
• Repairs, servicing and electric connections must be carried out by a qualified technician.
• The ambient temperature must always be between -5° C and +45° C.
• If this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
• Plastic bags must be kept out of reach of children.
• The unit must be installed out of the reach of children. Never leave the unit running unattended when connected to a power supply.

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

UNPACKING INSTRUCTION

ATTENTION!
Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain the packing material for inspection if any parts appear damaged from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packed. If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

POHERSUPPLV

The label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.

WARNING!
Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to avoid the risk of electrocution or fire.

INSTALLATION

• Step 1: Place the unit on a flat surface and in a suitably large area with at least 50 cm of open space around the unit.
• Step 2: Fill the fluid tank with Beamz snow fluid.
• Step 3: Plug the power cord into the outlet and turn on the unit, put the power switch to the “ON” position. The LCD display will show “WARMING UP”. After few
• seconds the LCD display will shows “READY”.
• Step 4: Using the LCD display panel, set the unit to the desired operating mode.
• Step 5: Turn off the unit, put the power switch to the “OFF” position and pull out the power cord from the outlet.

WARNING!
Use only the original Beamz snow fluid. Warranty will be voided if any other type of liquid is used, improper use of liquid may lead to machine failure and malfunction.

OPERATION

When the display shows “READY”, you can start producing haze and adjust the settings via LCD display panel.

100% by means of the Up/Down keys.
Interval Set xxxS| Adjust the interval between 1 to 100S by means of the Up-/Down keys.
Duration Set xxxS| Adjust the duration between 1 to 100S by means of the Up-/Down keys..
Volume Out xxx%| Adjust the volume output within the range of 0- 100% by means of the Up-

/Down keys.

DMX 512 #xxx| Adjust the DMX address for DMX control by means of the Up-/Down keys.
Wind For Class xx| Adjust the wind output during the function within the range of 0- 100% by means of the Up-/Down keys.
Wireless| Turn on/off wireless remote

WIRELESS REMOTE

• A ON / OFF
• B ON / OFF
• C Increase output level
• D Decrease output level

WARNING!
The device may produce snow for a maximum of 2 minutes continuously. Afterwards, the device must rest for at least 1 minute.

DMXS12 CONTROL

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.

CAUTION!
At the last unit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor between signal (-) and signal (+) and connect it to the DMX output of the last unit in the line .

DMX CHANNELS

CLEANING

We recommend frequent cleaning of the unit, in particular the output nozzle.

CAUTION!
There are no serviceable parts inside the unit except for the fuse. Repairs and service operations are only to be carried out by authorized dealers.

WARNING! Disconnect from mains before starting maintenance operation!

• Ensure the fluid do not become contaminated.
• Ensure the air vents are not clogged by dust. If necessary remove the dust.
• Ensure that the unit can not get overheated.
• Do not run the unit without any fluid, as the pump will run dry.
• Wipe up spilled fluid immediately. Moisture and fluid can permanently damage the electrical components of the unit.
• For cleaning the surface of the unit use a suitable, solvent-free cleaner.
• It is recommended to run the unit on a monthly basis in order to achieve best performance and output condition.
• Before storing, run distilled water through the system. This will help clean out the remaining snow fluid and prevent the pump from malfunctioning on next usage.

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug the main lead.

Procedure:

• Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
• Step 2: Remove the old fuse from the fuse holder.
• Step 3: Install the new fuse in the fuse holder.
• Step 4: Replace the fuse holder in the housing.

beamZ
Offers a wide range of high-performance lighting equipment and related accessories for the rental, entertainment, and architectural lighting markets. BeamZ Pro stands for performance, innovation and value pricing!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>