Beacon LIGHTING 011663 Lexicon Pendant Instruction Manual

Beacon LIGHTING 011663 Lexicon Pendant

Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation, and use of this product. Please keep instructions for future reference.

Warranty

• This luminaire is covered by a 12-month warranty. The warranty is from the date of purchase, not the date of installation.
• If the luminaire is not assembled and installed by a licensed electrician the warranty will be void.
• Please retain the proof of purchase and evidence of installation by a licensed electrician.
• The warranty will be void if there is any damage due to improper usage or modification of the luminaire.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation requirements

• Must be assembled and installed by a licensed electrician.
• All wiring and installation of the luminaire must adhere to the latest local and national wiring rules. eg. AS/NZS 3000 Electrical installations.
• Do not exceed the maximum wattage rating.
• Select a suitable location for installation:
  • This product is suitable for indoor use only.
  • The mounting point must support 2 times the weight of the luminaire.
  • Ensure the luminaire is not installed in the direct line of an air vent/system.
  • If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
• Take care not to pull any electrical wires during unpacking as this may damage the connection.
• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
• Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.
• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. To help with assembly, lay the luminaire on its side on a smooth non-scratch surface.

2. Use the mounting bracket (E) as a template to mark the position of the holes in the ceiling.

3. Drill holes into the ceiling and place the plastic anchors (D) into the holes. Secure the mounting bracket (E) onto the ceiling with the screws (F) provided. Ensure the screws (F) and anchors (D) used are suitable for the mounting surface and the surrounding environment.

4. To change the height of the pendant, adjust the cord suspension length by loosening the cord anchorage (H). After reaching the desired height, ensure the cord anchorage (H) is re-tightened without damaging the cord (I).

5. Connect the main supply wire to the terminal block (B) provided. Ensure that the wires are secure and no bare wires are exposed. Then secure the cover (C) on the terminal block.
   Mains Supply Wire Earth – Yellow/Green Neutral – Blue or Black Live – Brown or Red
   Luminaire Wire / Terminal block Yellow/Green or Blue or N Brown or L

6. Install the canopy (G) onto the mounting bracket (E) and secure it by tightening the screws on the side (A).

7. Install the shade (L) on the main body (J) securing by the lamp holder ring (M) and the decorative ring (N).  Alternatively, install the decorative ring (P – sold separately SKU# 011676, 011677, 011678, 011679) followed by the shade (L), then secure by the lamp holder ring (M).
   NOTE: This luminaire is only compatible with the following shades (sold separately): SKU# 011664, 011665, 011666, 011667, 011668, 011669, 011673, 011674, and 011675.

8. Install a globe (O – not included) into the lamp holder (K). Do not exceed the maximum wattage rating.

9. After the installation, switch on the luminaire to test and enjoy your new lighting product.

NOTE: This luminaire is only compatible with the following shades (sold separately): SKU# 011664, 011665, 011666, 011667, 011668, 011669, 011673, 011674, and 011675.

Safety Tips

• Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe, or making any adjustments to the luminaire.
• To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
• To clean, wipe with a damp clean cloth. Do NOT soak or immerse the product in water or other liquids.

Specifications

(without
 | shade)| shade)| shade)| shade)| shade)
Weight| 1.0kg (Max.| 1.5kg (Max.| 1.3kg (Max.| 1.5kg (Max.| 1.5kg (Max.
 | weight with| weight with| weight with| weight with| weight with
 | shade)| shade)| shade)| shade)| shade)
Canopy size|  | H:25mm| Dia:110mm|
Dimensions| H:100mm    Dia:100mm    Susp:2000mm (without shade)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>