BOSCH Indego Intelligent Robot Lawn Mower Instruction Manual

Original instructions

Intelligent Robot Lawn Mower

Safety Notes

Warning! Read these instructions carefully, be familiar with the controls and the proper use of the machine.
Please keep the instructions safe for later use!
Explanation of symbols on the machine

| General hazard safety alert.
Ensure no exits are blocked or obstructed by the machine.
---|---
| Warning: Read user instructions before operating the machine.
| Warning: Operate the disabling device before working on or lifting the machine.
| Caution: Do not touch rotating blades. Sharp blade(s). Beware of severing toes or fingers.
| Wait until all machine components have completely stopped before touching them. The blades  continue to  rotate after the machine is switched  off, a rotating blade can cause injury.
| Pay attention that bystanders are not injured through foreign objects thrown from the machine.
| Warning: Keep a safe distance from the machine when operating.
| Do not ride on the machine.
| Battery charger contains a safety transformer.

Operation

• Before working on the machine itself (e. g. maintenance, tool change, etc.) as well as during transport and storage, remove the isolator key from the machine.
• Never allow children or people unfamiliar with these instructions to use the machine. Local regulations may restrict the age of the operator.
• This machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they  have been given supervision or instruction concerning  use of the machine by a person responsible for their safety. Children should be supervised to ensure that they do not play with the machine.
• The operator or user is responsible for accidents or hazards occurring to other people or their property.
• If any hazard occurs whilst the machine is operating immediately press the red stop button.
• Ensure correct installation of the perimeter wire as instructed.
• Check the perimeter wire is fully pegged to the ground avoiding any slack lengths of wire.
• Periodically inspect the area where the machine is used and remove all stones, sticks, wires and other foreign objects.
• Do not run over any live mains cable running in the working area.
• Periodically inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance.
• Never operate the machine with defective guards or without safety devices.
• Do not put hands or feet near or under rotating parts.
• Never pick up or carry the machine while the motor is running.
• Do not leave the machine to operate unattended if you know that there are pets, children or people in the immediate vicinity.
• Start the machine according to the instructions standing well away from rotating parts.
• Do not use the product at the same time as a sprinkler or use the schedule to ensure that the two systems never run simultaneously.
• Do not modify this product. Unauthorized modifications may impair the safety of your product and may result in increased noise and vibration.

Remove the isolator key:
– before clearing a blockage,
– before checking, cleaning or working on the machine,
– if the machine vibrates abnormally (stop and check immediately),
– after striking a foreign object. Inspect the machine for damage and get advice on necessary repairs from your Bosch Service Centre.
Maintenance and Storage
Always wear gardening gloves when handling or working near the sharp blades.

• Before working on the machine itself, remove the isolator key.
• Before working on the docking station or power supply, remove plug from mains.
  Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all grass and debris, especially from the ventilation slots.

Turn the machine on its back and clean the blade area regularly. Use a stiff brush or scraper to remove compacted grass clippings. (see figure A) Blades are reversible. (see figure B)  Keep all nuts, bolts and screws tight to be sure that  the machine is in safe working condition.

• Periodically visually inspect the machine and replace worn or damaged parts for safety.
• Ensure that only official Bosch replacement parts are used.
• Replace all blades and bolts as a set as required.

Storage

• Remove isolator key when storing.
  During winter season store the machine and the docking station in a secure, dry place, out of the reach of children.
  Do not place other objects on the machine or docking station.

SD-Card
The machine has a SD-Card interface to allow software diagnosis by a Bosch Service Centre.

Battery Hazards

• Recharge only in the Bosch approved docking station.
• In the unlikely event of liquid being ejected from the bat­tery avoid all contact with the machine. If contact with the liquid occurs, seek medical advise.
• If the battery becomes defective, liquid can escape and come into contact with adjacent components. Check any parts concerned and contact the Bosch Service Centre.
• Do not open the machine and battery inside. Danger of short-circuiting and electric shock.
• Protect the machine against fire. Danger of battery ex­plosion.
• In case of damage and improper use of the machine, va pours may be emitted from the battery. Provide for fresh air and seek medical help in case of complaints. The vapours can irritate the respiratory  system.

Store the machine only within a temperature range between 5 °C and 45 °C. As an example, do not leave the machine in the car in summer.

Safety Warnings for Docking Station and Power Supply

• Only charge via the official Bosch docking station. Oth­erwise there is danger of fire and explosion.

• Check the docking station, power supply, cables and plugs periodically. If damage is detected, do not use the docking station or power supply. Never open the docking station or power supply. Have  repairs per- formed only by a qualified Bosch technician and only using original spare parts. A damaged docking station, power supply, cable or plug increases the risk of an electric shock.

• Do not operate the docking station and power supply on easily flammable surfaces (e. g., paper, textiles, etc.) or surroundings. The heating of the docking station and power supply during the charging process  can pose a fire hazard.

• Supervise children at all times. This will ensure that chil­dren do not play with the docking station, power supply or the machine.

• Children or persons that owing to their physical, senso ry or mental limitations or to their lack of experience or knowledge, are not capable of safely operating the docking station or power supply,  may only use this docking station and power supply under supervision or after having been instructed by a responsible person. Otherwise, there is danger of operating errors and injuries.

• The voltage indicated on the power supply must corre­spond to the voltage of the power source.
  The power supply should ideally be connected into a socket that is protected by a circuit-breaker that is actuated by a 30 mA residual current. Check your Residual Current Device (RCD) at regular intervals.
  The supply cord must be inspected for signs of damage at reg­ular intervals and may only be used if in perfect condition.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Only use or replace cables for the docking station and power supply with Bosch approved parts.

• Never touch the mains plug with wet hands. Do not run over, crush or pull the cables.

Protect the cables from heat, oil and sharp edges. The power supply/docking station is double insulated for safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Contact your Bosch Service Centre for details. If in doubt contact a qualified electrician or the nearest Bosch Service Centre. The connection lead must be inspected for signs of visible damage and ageing at regular intervals and may only be used if in perfect condition. Products sold in GB only: Your product is fitted with a BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362). If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the same fuse rating as the original plug. The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

Symbols

The following symbols are important for reading and understanding the operating instructions. Please take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the garden product in a better and safer manner.

Intended Use

The garden product is intended for domestic lawn mowing.

Technical Data

Working area size … maximum
… per charge up to| CN CN
E E| 1000
200
Weight| kg| 11.
Degree of protection| | IPX1
Serial number| see type plate on the garden product
Battery| | Li-Ion
Rated voltage| V=| 32.
Capacity| Ah| 3.0
Number of battery cells| | 18
Operating time, average up to| min| 50
Charging period (max.)| min| 50
Perimeter Wire| |
Perimeter wire
… minimum working length … maximum working length| E E| 20
450
Docking Station| |
Input voltage| V| 42
Power consumption| W| 150
Charging current| A| 2.0
Allowable charging temperature range| °C| 5 …45
Weight| kg| 2.0
Degree of protection| | IPX1
Power Supply| |
Input AC| V| 220.240
Protection class| |
Hill

*depends on cutting height, grass conditions and moisture
**protected against splashing water from all directions The values given are valid for a nominal voltage [U] of 230 V.
For different voltages and models for specific countries, these values can vary. Please observe the article number on the type plate of your garden product. The trade names of the individual garden products may vary.

Noise/Vibration Information
Measured sound values determined according to EN 60335.
Typically the A-weighted noise levels of the product are:
Sound pressure level 64 dB(A); sound power level 72 dB(A).
Uncertainty K =2.74 dB.

Declaration of Conformity
We declare under our sole responsibility that the product described under “Technical Data” is in conformity with the following standards or standardization documents:
EN 60335 (battery powered product) and EN 60335 (battery charger) according to the provisions of the directives 2011/65/EU, 2006/95/EC, 2004/108/EC, 2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level 75 dB(A). Conformity assessment procedure according to Annex VI.
Equipment category: 32
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS,
Stowmarket, Suffolk IP14 1EY, England

Explanation of Installation Guide

Lawn Preparation
Remove stones, loose pieces of wood, wire, live mains cables and other foreign objects from the cutting area.
Make sure that the cutting area is even and has no ditches, grooves and steep slopes above 20° that are clear obstructions for the machine.
Cut the main area of the lawn with a conventional mower to a max. height of 40 mm and the perimeter wire area to a max. height of 20 mm.

Installation

For a video guide on how to install the Indego please visit www.bosch- indego.com or use the following QR-Code.

http://www.bosch-do-it.com/qrcodegenerator/dispatch/1161

Select a position for the docking station, horizontally leveled and out of direct sun light.
Make sure that the docking station is placed by the side of the cutting area with a straight 2 m track in front and behind.
Whilst stood in the grass area to be cut it is important that the docking station charging pins point to the left. (see figure 2)
Note – If the docking station is positioned with the charging pins pointing either into the grass area or pointing to the right the Indego will not leave the dock.
Pull the wire end through the front hole of the base plate and straight through the wire duct and the rear hole. Fix the wire with a peg inline with the hole. Cut off insulation carefully and connect the wire to the right hand (red) terminal.  (see figures 4 – 5)
Fix the docking station with 4 supplied fixing pins to the ground. (see figure 6)
Lay out the perimeter wire anti-clockwise and flush to the ground. Observe the minimum distances from lawn edges, steps, walls, ponds, etc. Use the spacing guide. (see figure 7)
Trees, ponds, flower beds, etc. on the lawn must be delimited in clockwise direction. The lines to and from these zones may not cross but the wire should be touching. (see figure 7)
Fix the wire with the first peg next to the docking station, tension and fix with pegs at a distance of approx. 50 cm. (see figure 7)
Continue the loop and bring the wire to the back of the docking station and inline with the other end of the wire. Fix the second end of the wire also with the peg. Perimeter wire and peg should be installed inline.
Shorten the wire, cut off insulation carefully and connect the wire to the left hand (black) terminal. (see figure 8)
Clip on the protective cover of the docking station. (see figure 9)
Note: The wire can be extended up to the maximum allowed length of 450 m.
Note: If verticutting or raking is intended avoid the perimeter wire.
Install the power supply in a cool, dry environment. Connect it with the docking station and an indoor mains socket. (see figure 10)
Check the indicator on the docking station (see figure 11):
–Indicator lights up continuously green, if the output voltage of the power supply is available and the perimeter wire is not interrupted.
–Indicator flashes green, if the perimeter wire is broken, long or short.
–Indicator does not light up when the output voltage of the power supply is not available.

Initial Programming

Plug the isolator key into the machine and put it into the docking station for charging. (see figures 12 – 14)
The welcome screen appears and shows following symbols:

After-sales Service and Application Service

www.bosch-garden.com
In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the garden product.
Additionally be aware of your product’s software version (see “Menu > Settings

System Options > Info”).
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com

Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au

Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
www.bosch-garden.com
F 016 L70 825 (2012.11) O / 310 UNI

References

• Location selection | Bosch DIY
• Location selection | Bosch DIY
• Home | Bosch in Australia

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>