Darkglass Electronics 500W Bass Amplifier User Manual

: July 23, 2024
: Darkglass Electronics

Table of Contents

Specs
Technical Specifications
Dimensions
Block Diagram
Warning
Troubleshooting
Warranty
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Darkglass Electronics 500W Bass Amplifier

Specs

Controls

Passive/Active: Use this push button switch to change from passive to active mode. If your bass is active, it can have a hotter signal that makes the amp distort early (but Feltre to use if such additional distortion is desired!).
Distortion: Use this push button to turn the Alpha· Omega Engine on or off to add natural compression, organic harmonic enhancement, and saturation ranging from mild overdrive to high gain bass rage. The Alpha· Omega Engine operates before the clean section (you can therefore use the 6-Band Active EQ for additional tone shaping).
Bite: Boosts high mids (2.8kHz)for additional presence and definition.
Growl: Shelving Bass Boost for a fatter tone and increased low-end saturation.
Compression: This knob controls the amount of dynamic compression added to the Alpha ·Omega Engine. The makeup gain is adjusted automatically. Compression can be turned off or assigned using the Darkles Suite.
Drive: This knob controls the amount of distortion that the Alpha·Omega Engine will deliver. It will change from a soft, warm overdrive to a massive, modern distortion sound.
Level: Use this knob to control the output volume of the Alpha·Omega Engine.
Blend: Use this knob to mix between the Clean signal and the Distortion signal (Alpha·Omega Engine).
Mod: Selects or mixes between the two distinct distortion circuits: Alpha is punchy and tight with a lot of definition, whereas Omega is simply brutal and raw.
Bass: +-12dBat 80Hz. Use this slider to change the lowed content of the signal.
Mids: +-12dBat 250, 500,1.5k and 3kHz. These sliders control the mid content of the signal.
Treble: +-12dBat 5kHz. Use this slider to change the high content of the signal.
Master: Use this knob to control the overall volume of the amplifier.
Mute: Use this push button to mute the amplifier.

Technical Specifications

Input Impedance:	1MΩ
Minimum Load Impedance:	3Ω
Maximum Power Output:	500 W RMS @ 4Ω 250 W RMS @ 8Ω
Power Amp Input Impedance:	1MΩ
Power Amp Input Level:	2400 mV RMS
Pre-Amp Output Impedance:	1kΩ
Pre-Amp Output Level:	2400 mV RMS
Maximum Power Consumption:	approx. 700VA Forced-air cooled
AC Input Power:	100-120/210-250 VAC (using selector switch on left side

panel).
Cycles| panel). Cycles: 5

Dimensions

Width:	18 cm / 7.1″
Length	23 cm/ 9,1
Height	: 7,1 cm / 2,8″
Weight	2.4 kg / 5,29 lb

Block Diagram

Warning

There are no user-serviceable parts inside the amplifier. Do not open the amp.
Never use the amp in a high moisture environment or near liquids.
The Alpha· Omega 500 can deliver more than 115 dB of power. Exposure to this level of sound can damage your hearing. Always use proper hearing protection when exposed.
The Alpha· Omega 500 can deliver more than 500 Watts. Be sure that your speaker cabinets able to deliver that power.
Do not cover the vent holes. The fan and vent holes are part of the cooling system of the amp. Covering the vent holes can lead to overheating and damage to the amplifier.
Do not use an instrument cable as speaker cable. An instrument cable is not designed to deliver the type of power sent from the amplifier to the speaker.

Troubleshooting

The button controls do Notre act: check if the footswitch is connected. If you do not want to use the footswitch, you have to unplug the cable from the rear panel of the amp.
The amp does not turn on: check if the power cable is connected and if you have power from the wall.
The sound is low: check your speaker cable. Never use an instrument cable.
The sound is distorted or too high: check if the passive/active switch matches your bass.

Warranty

Please register for your warranty at http://mypedal.darkglass.com. The Alpha·Omega 500 is under warranty to the original owner for a period of two years against manufacturing defects in the country where the product was originally purchased.

If you experience a problem with the unit, please contact support@darkglass.com to receive a Return Authorization number or for information on the nearest authorized repair center. A copy of your original receipt must be included with all warranty repairs. You are responsible for all shipping charges. The unit must be shipped to us freight prepaid. We will return the unit freight collect.

Electronics Oy is not responsible for shipping damage either to or from our service center. Claims must be filed with the carrier. For repairs please contact your local dealer or distribute or for your country’s specific warranty period and repair procedures.