BLACK LION AUDIO PBR TT Patchbay Owner’s Manual
- June 9, 2024
- BLACK LION AUDIO
Table of Contents
BLACK LION AUDIO PBR TT Patchbay
CONNECTIONS
The PBR TT offers 96 points of connectivity for your studio gear, allowing for
permanent installation and routing of your favorite hardware while still
allowing for flexible and creative patching.
The PBR TT Patchbay offers Normalled, Non-Normalled, and Half-Normalled
operation, switchable from the top of the unit on a per-module basis. A
module, in this context, is any set of vertically-aligned jacks on the
patchbay; TT on the front and DB25 on the back.
A typical patchbay configuration will have device outputs sent to the top rear
row of patch points with device Inputs connected to the rear bottom row. For
example, you would connect the Input of a delay unit or compressor to a DB25
output connection on the rear of the patchbay, and connect the delay’s Output
to a DB25 Input connection, also on the rear.
-
Balanced TT connections:
Accepts TT (Bantam) jacks for connecting and routing your audio gear. Accepts balanced connections. -
Normal/Non-Normalled/Half-Normalled Switches:
Switch-es the routing for its respective module between Normal, Non-Normal, and Half Normalled operation. Switch up = Half-Normal, Switch mid = Non- normal. Switch down = Normal -
DB25 connections.
Accepts DB25 connections (eight channels in a breakout cable) for connecting to the inputs and outputs of your outboard equipment. Common convention is to connect the top row of connections to device outputs and the bottom row to device inputs. -
Grounding lug.
Connect this to your outboard equipment using a ground wire to prevent noise from ground loops.
SIGNAL FLOW IN YOUR TT PATCHBAY
The flow of signal through a patchbay module is affected by both physical
connections and mode setting (Normalled, Non-Normalled, or Half-Normalled.)
The most common configuration for a patchbay is for signals to come in to the
patchbay from the top rear connections, and out of the patchbay from the
bottom rear connections. Conversely, on the front of the patchbay, the top row
connections are outputs and the bottom row connections are inputs.
With jacks connected to the top rear and bottom rear of a single patchbay
module, signals coming into a top rear connection are passed directly through
to the output on the bottom rear, as shown here. This connection style should
be used for your hardware’s “default” configuration – the way you want your
signals to flow on a day-to-day basis.
When no jacks
are connected to the top connections of a module, a signal from the front
bottom input is passed through to the rear bottom output.
When all four
jacks are connected to a patchbay module, a signal connected to a rear top
input of the patchbay is passed to the front top output, while signal from the
front bottom input is passed to the rear bottom output.
OPERATION
NORMALLED OPERATION
When a module
is set to Normalled and connections are made to the top rear and top front
jacks, the signal is passed through from the top rear to the top front –
breaking the connection.
A Normalled
configuration allows you to run several devices in series by using patch
cables on the front of the patchbay to interconnect several of your devices.
For example, you could run a signal from a preamp, to a compressor, and
finally to a reverb. A cable inserted into the bottom rear will have its
connection broken when a cable is inserted into the top front.
HALF-NORMALLED OPERATION
When a module is set to Half-Normalled and connections are made to the rear
top, rear bottom, and front top jacks, the signal is passed through from the
top rear to the top front – without breaking the connection.
This allows
you to use the patchbay as a molt (splitter), sending the signal coming into
the patchbay to two different destinations; very useful for parallel
processing of your signal and monitoring applications. Inserting a cable in to
the front bottom jack of a half-Normalled module will break the connection
between the rear jacks.
NON-NORMALLED OPERATION
AKA “open.” In non-Normalled configuration, the top and bottom rows of jacks
are not connected at all. Modules set to non-normalled operation will pass
signal straight through from front-to-back
or back-to-front, but not vertically. Useful for setups where you do not want
your devices to automatically route anywhere.
ON PHANTOM POWER
We advise against running phantom power through your patchbay, as this makes it possible to send phantom power to a device not designed to handle it; expensive damage could result!
DB25 WIRING CONVENTION
The PBR TT Patchbay uses the Tascam DB25 wiring convention. Some audio
equipment uses the Yamaha convention. Check the documentation for your other
DB25 hardware to ensure compatibility.
NOTICE
This manual provides general information, preparation for use, installation
and operating instructions for the Black Lion Audio PBR-Series Patch bays.
The information contained in this manual is subject to change without notice.
Black Lion Audio makes no warranties of any kind with regard to this manual,
including, but
not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Black Lion Audio shall not be liable for errors contained
herein or direct, indirect, special, incidental, or consequential damages in
connection with the furnishing, performance, or use of this material.
©2023 Black Lion Audio. The Black Lion Audio ‘Lion Face’ logo, BLA, are
trademarks or registered trademarks of Black Lion Audio.
This manual and any associated intellectual property are subject to copyright
protection. No part of this document may be reproduced in any form without
explicit written consent from Black Lion Audio.
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions.
- Keep these instructions
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
- Use only attachments/accessories specified by the manufacturer
- Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid in-jury from tip-over.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been ex-posed to rain or moisture, does not operate normally, or has been dropped.
- This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids, such as vases, shall be placed on the apparatus.
- Any changes or modifications not expressly approved in this manual could void your authority to operate this apparatus.
COMPLIANCE
This product complies with all international standards for safety and
emissions including IEC62368 and FCC Part 15-B.
Do not attempt to service this unit yourself, as it will void your warranty.
Please check your unit carefully upon receipt and return to place of purchase
immediately if there are any problems with the product. After that, the
standard Black Lion Audio 3 YEAR warranty will apply to defects in materials
and workmanship.
U.S.A.
Should your Black Lion Audio product require service, please contact us on
our customer service site: https://www.blacklionaudio.com/contact. You must
obtain an RA # (Return Authorization number) from us before shipping a unit
back to us. This RA # must be clearly written on the outside of the box.
Please safely pack the units…It is best to use the original packing materials.
Black Lion Audio cannot be responsible for any damages incurred in shipping to
us due to poor packaging. PLEASE PACK CAREFULLY and FULLY INSURE THE SHIPMENT.
INTERNATIONAL
For service or warranty assistance, please contact the Black Lion Audio
distributor in your country through the dealer from whom you purchased this
product.
LIMITED 3 YEAR WARRANTY
Black Lion Audio’s PBR TT Patchbay are warranted by Black Lion Audio to be
free from defects in materials and workmanship for the period of THREE (3)
YEARS to the original purchaser. In the event of such defects, the product
will be repaired without charge or, at our option, replaced with a new one if
delivered to Black Lion Audio prepaid, together with a copy of the sales slip
or other proof of purchase date. The warranty excludes problems due to normal
wear, abuse, shipping damage or failure to use the product in accordance with
the specifications.
All parts and labor are covered under this Limited Warranty. However, if it is
determined by Black Lion Audio that the device was damaged or made defective
through abuse, we reserve the right to charge the customer for the cost of the
repair.
Black Lion Audio shall not be liable for damages based upon inconvenience,
loss of use of the product, loss of time, interrupted operation or commercial
loss or any other damages, whether incidental, consequential or otherwise.
This warranty gives you specific legal rights, and you may have other rights,
which will vary from state to state.
This warranty is not transferable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>