ZEBRA ZQ220 Plus Mobile Printer User Guide

ZEBRA ZQ220 Plus Mobile Printer

Regulatory Information

• This device is approved under Zebra Technologies Corporation.
• This guide applies to the following model numbers:
  • ZQ220 Plus
• All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required.
• Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user’s authority to operate the equipment.
• Declared maximum operating temperature: 40°C
• Zebra devices are professionally installed — the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation.
• Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations.

Bluetooth® Wireless Technology

This is an approved Bluetooth® product. For more information on the Bluetooth SIG listing, please visit www.bluetooth.com.

Regulatory Markings

• Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: www.zebra.com/doc.
• The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the device by following these instructions: Go to Settings > Regulatory.

Health and Safety Recommendations

• Ergonomic Recommendations
  In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.

• Safety in Hospitals and Aircraft
  Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircraft’s operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments.

• Medical Devices

  • It is recommended that a minimum separation distance of 20 cm (8 inches) be maintained between a wireless device and a medical devices such as pacemakers, defibrillator, or other implantable devices to avoid potential interference with the medical device. Pacemaker users should keep the device at the opposite side of the pacemaker or turn OFF the device if suspected of interference.
  • Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure – Use Properly

• Only operate the device in accordance with the instructions supplied.
• The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc.
• Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide.
• The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided.
• For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at www.zebra.com/responsibility.

Marking and European Economic Area (EEA)

• Statement of Compliance
  • Non-radio devices: Zebra hereby declares that this equipment is in compliance with Directives 2014/30/EU, 2014/35/EU and 2011/65/EU.
  • Radio enabled devices: Zebra hereby declares that this equipment is in compliance with Directives 2014/53/EU and 2011/65/EU.
  • Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity.
  • The full text of the EU Declaration of Conformities is available at: www.zebra.com/doc.
  • EU Importer : Zebra Technologies B.V
  • Address: Mercurius 12, 8448 GX Heerenveen, Netherlands
• Waste Electrical and Electronic Equipment (WEEE)
  For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at: www.zebra.com/weee.

United States and Canada Regulatory

Radio Frequency Interference Notices

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1.  this device may not cause harmful interference
  2. this device must accept any interference received including interference that may cause undesired operation.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. harmful interference in a residential installation. This equipment generates, uses and can radiate radio

Radio Frequency Interference Requirements – Canada

• Innovation, Science and Economic Development Canada ICES003 Compliance Label: CAN ICES-003 ([B])/NMB-003([B])
• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure Information – FCC and ISED

• The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
• The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Statement of Compliance

• Non-radio devices: Zebra hereby declares that this equipment is in compliance with Electromagnetic Compatibility Regulations 2016, the Electrical Equipment (Safety) Regulations 2016 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
• Radio enabled devices: Zebra hereby declares that this equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
• Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity.
• The full text of the UK Declaration of Conformities is available at: www.zebra.com/doc.
• UK Importer: Zebra Technologies Europe Limited
• Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF

Warranty

For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.

Service Information

• Before you use the unit, it must be configured to operate in your facility’s network and run your applications.
• If you have a problem running your unit or using your equipment, contact your facility’s Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com/support.
• For the latest version of the guide go to: zebra.com\support.

Software Support

• Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To confirm that your Zebra device has the latest entitled software available at the time of purchase, go to zebra.com/support.
• Check for the latest software from Support > Products, or search for the device and select Support > Software Downloads.
• If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:
  • Model number
  • Serial number
  • Proof of purchase
  • Title of the software download you are requesting.
• If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software.

Product Support Information

• For information on using this product, see the user guide at: www.zebra.com/ZQ220 Plus-info
• To find quick answers to known product behaviors, access our knowledge articles at supportcommunity.zebra.com/s/knowledge-base.
• Ask your questions in our Support community at supportcommunity.zebra.com.
• Download product manuals, drivers, software, and view how-to videos at zebra.com/support.
• To request a repair for your product, go to zebra.com/repair.

References

• Zebra Support Community
• Zebra Support Community
• ZQ200 Series Mobile Printers | Zebra
• ZT231 Industrial Printer Support & Downloads | Zebra

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>