AXIOM SW2100P Compact Band Pass or Bass Reflex Passive Subwoofer User Manual

: June 9, 2024
: AXiom

Table of Contents

KEY FEATURES
INTRODUCTION
TECHNICAL SPECIFICATION
MECHANICAL DRAWING
LIMITED WARRANTY
SAFETY INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**AXIOM SW2100P Compact Band Pass or Bass Reflex Passive Subwoofer

**

KEY FEATURES

Band-Pass/Bass-Reflex Active Subwoofer
Very compact enclosure
Single 21” Neodymium woofer with 4” ISV voice coil
Very good output to-weight ratio
Water repellent cone

INTRODUCTION

The SW2100P is a very compact Band-Pass/Bass-Reflex subwoofer providing high output and extended low frequency response. It is equipped with a single 21” neodymium transducer with a 4” ISV voice coil, large displacement suspension system, and composite reinforced, water repellent cone, able to provide clean and undistorted LF reproduction at very high SPL.

The loudspeaker is designed with a unique motor featuring a high grade neodymium magnet assembly in a structure optimized for thermal and magnetic efficiency. Its features include a large displacement suspension system which, in conjunction with a composite reinforced, straight ribbed cone and the proprietary Double Silicon Spider (DSS) technology, allows an ultra-linear piston action and provides full mechanical control across the entire working range. The 100mm (4 in) state-of-the-art voice-coil utilizing Interleaved Sandwich Voice coil (ISV) technology, provides high levels of thermal stability and durability. The ISV technology achieves a balanced linear motor unit exerting an exceptionally high force factor.

The phenolic birch plywood cabinet is equipped with pole mount socket, stacking feet, flush handles, and heavy duty wheels to enable easy handling and transportation.

It will deliver high level and extended low bass performance from a very compact cabinet, and thanks to the integral pole mount socket partners well with any of the ED point source and AXIOM line array loudspeakers in any audio applications, while its small size enables it to be easily fitted into tight venue spaces.

TECHNICAL SPECIFICATION

Acoustical

System’s Acoustic Principle
Band-pass / bass-reflex
Transducer
21” Neodymium magnet, 4” (100mm) VC High stiffness, water repellent cone, Interleaved Sandwich Voice coil (ISV), Triple-roll suspension
Frequency response (-6 dB)
34 Hz – 180 Hz (Processed)
Sensitivity (1.41V @ 1m, 2Pi)
94 dB
Maximum Peak SPL @ 1m
132 dB

Electrical

Nominal Impedance
4 Ω
Minimum Impedance
3 Ω @ 30 Hz
Power Handling Continuous*
1600 W
Power Handling Program
3200 W
Power Handling Peak
7200 W
Power Compression
@ -10 dB Power (320 W) = 0.62 dB
@ -3 dB Power (1600 W) = 2.18 dB
@ 0 dB Power (3200 W) = 3.57 dB
AES Pink Noise Power

Connectors

Connector Type
Neutrik® Speakon® NL4 x 2
Input Wiring
Pin 1+/1-; (Pin 2+/2- pass thru)

Mechanical

Width
760 mm (29.9”)
Height
511 mm (20.1”)
Depth
770 mm (30.3”)
Depth Including Wheels
881 mm (34.6”)
Construction
18mm, reinforced phenolic birch
Paint
Black High resistance, water based paint
Wheels
4 x heavy duty ø 100mm (4”) castors
Transport
8 handles
Net Weight
56 Kg (123.5 lbs)
60 Kg (132.3 lbs) including wheels

MECHANICAL DRAWING

OPTIONAL ACCESSORIES

NL4FX Neutrik Speakon® PLUG
DHSS10M20 Sub-Speaker ø35mm 1-1.7m Pole with Handle and M20 screw
KP210S Sub-Speaker ø35mm 0.7-1.2m Pole with M20 screw see http://www.axiomproaudio.com/ for detailed description and other available accessories.

S PARE PARTS

AC103GS 100 mm Swivel castor without brake
98SW2100WZ4 21’’ woofer – 4” VC – 4 ohm
NL4MP Neutrik Speakon® panel socket

REAR PANEL

INPUT – Power input for the external amplifier. The SW2100P does not include a passive crossover for filtering the signal. The connections are the following:
REAR PANEL

INPUT – LINK

LINK – Power output in parallel with the INPUT socket for connecting the unit to another speaker. The number of SW2100P cabinets that can be connected in parallel depends on the amplifier load capacity.

LIMITED WARRANTY

Proel warrants all materials, workmanship and proper operation of this product for a period of two years from the original date of purchase. If any defects are found in the materials or workmanship or if the product fails to function properly during the applicable warranty period, the owner should inform about these defects the dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed description. This warranty does not extend to damage resulting from improper installation, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and warranty is still valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defectiveness.

This unit package has been submitted to ISTA 1A integrity tests. We suggest you control the unit conditions immediately after unpacking it.
If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspection.
Proel is not responsible for any damage that occurs during shipment.
Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
Possible damages to unit should be immediately notified to forwarder. Each complaint for package tampered with should be done within eight days from product receipt

SAFETY INSTRUCTIONS

To reduce the risk, close supervision is necessary when the product is used near children.
Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.
This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.
This product should be located so that its location or position does not interfere with its proper ventilation and heating dissipation.
Care should be taken so that objects and liquids do not go inside the product.
The product should be connected to a power supply mains line only of the type described on the operating instructions or as marked on the product. Connect the apparatus to a power supply using only power cord included making always sure it is in good conditions.
WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connection.
Make sure that power supply mains line has a proper earth connection.
Power supply cord should be unplugged from the outlet during strong thunderstorm or when left unused for a long period of time.

CE CONFORMITY
Proel products comply with directive 2014/30/UE (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with directive 2014/35/UE (LVD),
as stated in EN 60065 standard.
PROEL S.p.A. (World Headquarter) – Via alla Ruenia 37/43 – 64027 Sant’Omero (Te) – ITALY
Tel: +39 0861 81241 Fax: +39 0861 887862 www.axiomproaudio.com