JET 728200 Flip-Top Stand Instruction Manual
- June 9, 2024
- JET
Table of Contents
JET 728200 Flip-Top Stand
Instructions and Parts List
IMPORTANT SAFETY INSTRUCTIONS
- Review all instructions before assembling the table. Improper assembly can cause personal injury and/or property damage.
- Do not exceed maximum load for the stand.
- Do not stand on this product.
- WARNING: This product can expose you to chemicals including lead and cadmium which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca.gov.
Tools required for assembly
10mm and 16mm wrenches (a manual ratcheting socket wrench will speed assembly time)
Shipping contents
- 1 Table Assembly
- 4 Lower Braces (2 Long, 2 Short)
- 4 Vertical Legs
- 4 Adjustment Legs
- 4 Leveling Pads
- 1 Instructions and Parts List
- 1 Product Registration Card
- 1 Hardware Package (728200-HP)
- 44 Carriage Bolt M6-1.0×16 – AA 44 Flat Washer 6mm– BB
- 44 Lock Washers 6mm –CC
- 44 Hex Nut M6-1.0–DD
Assembly instructions
Use the exploded view and parts list as guides to assembly. Make all leg and brace fasteners only finger tight until the entire unit has been assembled.
- Turn table assembly upside down; use a mat or piece of cardboard underneath to prevent scratching.
- Assemble the four main legs (#20) to the table brackets (#8/26). Finger tighten only.
- Determine the height desired, then connect the adjustment legs (#21) to the main legs. These can be repositioned later if needed. (It is recommended that each adjustment leg be secured by at least 4 screws to the main leg.)
- Determine placement of lower braces (#24/25) and assemble them to the main legs/adjustment legs.
- Install the leveling foot pads (#22) and tighten each hex nut (#23) against the adjustment leg. (If using the optional swivel casters, install those instead of the pads.)
- Turn the unit over and push down lightly to make sure stand rests evenly upon the floor.
- Fully tighten all fasteners. Take care to not overtighten.
Holes are provided in the lower braces for attaching a user-made shelf, not provided.
728200 Flip-Top Stand – Exploded View
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
728200 Flip-Top Stand – Parts List
Optional Accessory– Swivel Caster
28 …………… 98-0129 ………………….. Swivel Casters (set of 4) ………………………………………. ……………………………. 1 set
Operation
CAUTION: If the optional casters are used, make sure they are locked in place. To tilt table:
- Pull out left and right handles and rotate them 90-degrees to keep them disengaged.
- Begin tilting front edge of table downward until it just clears the handle pins, then turn handles 90-degrees and allow them to slide back in.
- Continue to tilt table slowly, while helping stabilize the machine(s), until table passes the beveled pins at the rear and snaps into level position.
warning: When machines are mounted to table, tilt table slowly and help stabilize the machines throughout the tilt process. Do not allow the table to swing uncontrollably. Failure to comply may cause personal injury and/or unnecessary stress upon stand components.
Machine selection
The stand will accept most bench top machines up to load capacity and within
the table size range (see specifications). Secure the machine to the table
with appropriate fasteners (not provided). Make sure machine(s) are securely
fastened before attempting to tilt the table. Position of machines upon the
table is user’s choice; however, consideration should always be given to the
machines’ center of balance and weight distribution. Ideally, they are
centered upon the table. But the design of some machines may require them to
be shifted off center for optimum position and/or easier tilting to the down
position.
(machines and
user-made shelf not provided)
Specifications for JET Flip-Top Stand
| Stock number | 728200 |
|---|---|
| Table size (D x W) | 20 x 25 in. (508 x 635 mm) |
| Height range | 29 to 34 in. (736.6 to 863.6 mm) |
| Height adjustment | 5.10 in. (130 mm) |
| Load capacity | 300 lb. (136 kg) |
| Table material | MDF/Vinyl |
| Assembled weight | 45 lb. (20 kg) |
| Shipping weight | 49 lb. (22 kg) |
The 728200 Flip-Top Stand will accommodate most bench top machines, including the following models:
| Brand | Model | Stock No. | Notes |
|---|---|---|---|
| JET | 13” Planer | 722130 | |
| JET | 8” Jointer/Planer | 707400 | |
| JET | 8” Grinder | 726101 | |
| JET | 1020 Drum Sander | 723510 | |
| JET | 9” Belt/Disc Sander | 708595 | |
| JET | Spindle Sander 5” | 708404 | |
| JET | 18” Scroll Saw | 727300B | |
| JET | 22” Scroll Saw | 727200B | |
| JET | 10” Miter Saw | 707210 | Secure miter arm before tilting underneath. |
| JET | 12” Miter Saw | 707212 | Secure miter arm before tilting underneath. |
| JET | JET Mortiser | 708580 | Remove handle if needed before tilting underneath. |
| Powermatic | PM Mortiser | 1791310 | Remove handle if needed before tilting |
underneath.
JET| 10” Band saw| 714400|
JET| 12” Drill Press| 716000|
JET| 15” Drill Press| 716200|
Powermatic| PM1250 Air Filtration| 1791250|
JET
- address: 427 New Sanford Road LaVergne, Tennessee 37086
- Ph.: 800-274-6848
- www.jettools.com
Part No. M-728200 Edition 2 03/2022 Copyright © 2022 JET
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>