HEINNER MG1600TA-UV Meat Grinder User Manual

HEINNER MG1600TA-UV Meat Grinder

Model : MG1600TA-UV

• Meat Grinder
• Max Power : 1600W
• Rated power : 700W

Thank you for purchasing this product

INTRODUCTION

• Before using the appliance, please read carefully this instruction manual and keep it for future reference.
• This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance.
• In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage.

In order to avoid rust we advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

CONTENT OF YOUR PACKAGE

• Meat grinder
• User manual
• Warranty card

DESCRIPTION

This appliance is equipped with a thermostat system. This system will automatically cut off the power supply to the appliance in case of overheating.

If you appliance suddenly stops running:

1. Pull the mains plug out of the socket.
2. Press the switch button to turn off the appliance.
3. Let the appliance cool down for 60 minutes.
4. Put the mains plug in the socket.
5. Switch the appliance on again.

Please contact your dealer of an authorized service center if the thermostat system is activated too often. If you plug in, the indicator light will be on.
CAUTION : In order to avoid a hazardous situation, this appliance must never be connected to a time switch.

IMPORTANT

1. Read these instructions for use carefully and look at the illustrations before using the appliance.
2. Keep these instructions for future reference.
3. Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
4. Never use any accessories of parts from other manufacture. Your guarantee will become invalid if such accessories or parts have been used.
5. Do not use the appliance if the mains cord, the plug or other parts are damaged.
6. If the mains cord of this appliance is damaged, it muse always be replaced by manufacture or a service center authorized, in order to avoid hazardous situations.
7. Thoroughly clean the parts that will come into contact with food before you use the appliance for the first time.
8. Unplug the appliance immediately after use.
9. Never use you finger or an objection to push ingredients down the feed tube while the appliance is running. Only the pusher is to be used for this purpose.
10. Keep the appliance out of the reach of children.
11. Never let the appliance run unattended.
12. Switch the appliance off before detaching and install any accessory.
13. Wait until moving parts have stopped running before you remove the parts of the appliance.
14. Never immerse the motor unit in the water or any other liquid, nor rinse it under the tap. Use only a moist cloth to clean the motor unit.
15. Do not attempt to grind bones, nuts or other hard items.
16. Never reach into the cutter housing. Always use the pusher.
17. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been give supervision or instruction concerning use of the appliance by a person responsible for their safety.
18. Children should be supervised to ensure that they do not play with the appliance.
19. If the appliance is locked, please press Reversal button (REV). The meat locked in cutter housing is untrodden, so the appliance can renew its usual condition.

USING INSTRUCTIONS

1. Press the fasten button，hold the head and insert it into the inlet when inserting please pay attention the head must be slanted as per arrow indicated on the top, see (fig.1), then move the head anticlockwise so that the head being fastened tightly.(fig.2)
2. Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into the motor housing. (fig.3)
3. Place the cutting blade onto the snake shaft with the blade facing the front as illustrated (fig.4).If it is not fitted properly, meat will not be grinded.
4. Place the desired cutting plate next to the cutting blade, fitting protrusions in the slot.(fig.5)
5. Support or press the center of the cutting plate with one finger then screw the fixing ring tight with another hand (fig.6). Do not over tighten.
6. Place the hopper plate on the head and fix it into position.
7. Locate the unit on a firm place.
8. The air passage at the bottom and the side of the motor housing should be kept free and not blocked.

MINCER

1. Insert the worm shaft into the cutter housing, the plastic end first.
   Place the cutter unit onto the worm shaft. (The cutting edges should be at the front) Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) onto the worm shaft. (Make sure the notch of the grinding disc fit onto the projections of the mincer head.) Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened.

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for mincing

Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle and sinews as much as possible.
Never use frozen meat!
Put the meat in the tray. Use the pusher to gently push the meat into the cutter hosing. (For steak tartare, mince the meat with the medium grinding disc twice. ) (fig.7)
Plug the unit on and switch knob to, then switch ON/0/R knob to ” ON ” position. After use it Plug the unit on and switch knob to, then switch ON/0/R knob to ” R ” position.

MAKING KEBBE

1. Insert the worm shaft into the cutter ho using, the plastic end first. (fig.8)
   Place the cone in the cutter housing.
   Place the former on the cutter housing and screw the ring on the cutter housing.(fig.9)

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for making kebbe. (fig.10)

Feed the prepared kubbe mixture through the kebbe maker. Cut the continuous hollow cylinder into the desired lengths and user as required.
Kebbe is a traditional Middle Eastern dish made primarily of lamp and bulgur wheat which are minced together to form a paste the mixture is extruded through the kubbe maker and cut into short lengths.The tubes can then be stuffed with a minced meat mixture, the ends pinched together and then deep fried.

MAKING SOUSAGES

1. Mince the meat

2. Insert the worm shaft into the cutter housing, the plastic end first. (fig.11)

3. Place the separator in the cutter housing.

4. Place the sausage horn on the cutter housing and screw the ring on the cutter housing.
   (Make sure the notches of the separator fit onto the projections of the mincer head.)

5. Attach the cutter housing to the motor unit.

6. Place the tray on the upright part of the cutter housing.

7. Now the appliance is ready for making sausages.

Put the ingredients in the tray. Use the pusher to gently push the meat into the cutter h ousing. Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin o nto the sausage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets stuck onto the sausage horn, wet it with some water.

TOMATO JUICER

1. Place the plastic screw locking ring into the sleeve.(fig.1)
2. Place the gauze into the sleeve next to the plastic screw locking ring.(fig.2)
3. Put the fixing ring through the sleeve and make it at the end of the sleeve.(fig.3)
4. Place the snake into the head, long end first, and turn to feed the snake slightly until it is set into the motor housing.(fig.4)
5. Insert the shaft of the snake into the central axis of the screw.(fig.5)
6. Put the whole sleeve along with the fixing ring through the screw, then move the fixing ring clockwise so that it being fastened tightly.(fig.6)
7. Put the plastic juice tray through the sleeve and make it on the suitable position.(fig.7)
8. Insert the plastic screw into the hole of the sleeve, then move it clockwise until it is properly fastened. Then place the plastic cover onto the sleeve.(fig.8)
   Now the appliance is ready for juicing.

HOW TO CLEAN YOUR APPLIANCES

Meat left behind in the cutter housing may be removed fro m the inside of the appliance by passing a slice of br ead through the cutter housing.

1. Before you clean the appliance, switch the appliance off and remove the plug from the socket.(fig.12)
2. Press the release button and turn the whole cutter housing in the direction of the arrow. Remove the pusher and the tray.(fig.13)
3. Unscrew the screw ring and remove all parts of the cutter housing. Do not clean the parts in the dishwasher!
4. Wash all parts that have come into contact with meat in hot soapy water. Clean them immediately after use.
5. Rinse them with clear hot water and dry them immediately.
6. We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

TECHNICAL DATA

• Max Power: 1600W
• Voltage: 220-240V, 50-60Hz

Environment friendly disposal

You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working electrical equipment’s to an appropriate waste disposal center.

HEINNER is a registered trademark of Network One Distribution SRL. Other brands and product names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any der ivative such as translation, transformation, or adaptation without permission from NETWORK ON E DISTRIBUTION. Copyright © 2013 Network One Distibution. All rights reserved.
www.heinner.com, http://www.nod.ro
http://www.heinner.com, http://www.nod.ro
This product is in conformity with norms and standards of European Community
Importer: Network One Distribution
Marcel Iancu Street, no. 3-5, Bucharest, Romania
Tel: +40 21 211 18 56, www.heinner.com , www.nod.ro

References

• Heinner – large appliances, small appliances, housekeeping, DIY
• Heinner – large appliances, small appliances, housekeeping, DIY
• NOD - Network One Distribution
• NOD - Network One Distribution

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>