Pando GRV 520-780 Hood Instruction Manual
- June 4, 2024
- PANDO
Table of Contents
GRV
520-780
User and Installation Manual.
The symbol on the product or its packaging indicates that this product cannot be disposed of like a normal domestic waste. The product must be handed over at a collection point for recycling electrical and electronic equipment. If you ensure that this product is correctly disposed of, you will help to avoid the possible negative environmental and public health effects that could arise from incorrect disposal. For more detailed information about recycling this product, please contact your city authorities, the domestic waste service, or the establishment where you purchased it. This electrical appliance is marked in compliance with European Directive 2002/96/EC on electrical and electronic appliance waste (WEEE).
INTRODUCTION
Firstly, we would like to thank you for your confidence in our firm when you
chose a Pando extractor hood.
This manual and its annexes are a guide for the correct installation, usage,
and maintenance of your new Extractor Hood.
To learn everything about your hood, we recommend you read these instructions
carefully from beginning to end and keep them for future reference.
Before starting the installation process read with care this installation
manual and the attached user’s manual, There are also instructions for the
correct installation of the product.
Installation should only be carried out by qualified professionals,
professional installers, or the official technical service. The manual or
installation guide must be read with care before starting the installation
process.
When opening the packaging, check that all the components are in a perfect
state and all the accessories are present. If this is not the case, contact
the dealer and do not install. Once installed, any damage to the exterior such
as scratches, dents, stains, etc. will not be covered by the guarantee.
The manufacturer will not be held liable for any possible inaccuracies due to
printing or transcription errors in this manual The manufacturer reserves the
right to incorporate modifications considered useful or necessary into the
products, which will not alter their essential functions and safety
characteristics.
RECOMMENDATIONS TO BEAR IN MIND BEFORE INSTALLATION.
VERY IMPORTANT!
DO NOT REMOVE THE PROTECTIVE PLASTIC FROM THE HOOD UNTIL IT IS COMPLETELY
INSTALLED, IF THIS PLASTIC IS NOT PRESENT IN AREAS THAT COULD HAVE A RISK OF
DAMAGE DURING INSTALLATION, IT IS RECOMMENDED TO APPLY PROTECTIVE MATERIALS
AGAINST IMPACT, SCRATCHES, AND CONTACT WITH CORROSIVE AGENTS.
TAKE SPECIAL CARE DURING THE INSTALLATION IF OTHER WORK IS ALSO IN PROGRESS
BECAUSE PAINT, SILICON, PLASTER, AND OTHER MATERIALS COULD CONTAIN CORROSIVE
CHEMICALS THAT MAY DAMAGE THE PRODUCT, IN THESE CASES IT IS RECOMMENDED TO
ADEQUATELY PROTECT THE HOOD, BY, FOR EXAMPLE, HERMETICALLY COVERING AREAS THAT
COULD BE AFFECTED WITH PLASTIC.
THIS WILL AVOID DAMAGE TO THE OUTSIDE OF THE APPLIANCE, SOMETHING THAT WILL
NOT BE COVERED BY THE GUARANTEE.
SAFETY INSTRUCTIONS
-
If the hood is to be used at the same time as gas-fuelled or other fuelled appliances (not applicable to appliances exclusively designed to blow air into the room) the room
must be properly ventilated. -
The exhausted air must not be led through a conduit that is used for exhausting fumes from other appliances using gas or other fuels (not applicable to devices destined exclusively to discharge the air inside the room).
-
The minimum distance between the surface of the cooktop and the lower edge of the hood must be 65 cm if the extractor hood is fitted over the gas cooker. If the installation
instructions of the gas cooker indicate a greater distance, this must be followed. -
Regulations regarding air evacuation must be respected.
-
If the hood does not have a power cable with a plug, or other means for disconnection from the mains, with a separation of all poles to ensure total disconnection under category III conditions of overvoltage, means for disconnection of the fixed installation must be incorporated in accordance with installation regulations.
-
Once the appliance has been delivered, within 24h, remove the packaging and check that it is in a good state, visually inspecting the general state of the outside. If any anomaly or damage is observed, do not install and immediately inform the dealer or installer within 24h of reception.
-
This hood has been designed for normal domestic use. It must not be used for industrial, professional , or any other use different from what it has been designed for.
-
Pando will not be held liable for consequences or damages resulting from incorrect installation or misuse of the appliance.
-
Do not try to alter any of the characteristics of this appliance, this could be dangerous and will automatically render the guarantee void.
-
It must be possible and accessible for the user to disconnect the appliance from the mains after installation. The power plug should be easily accessible, if this is not the case, a switch for electrical disconnection, compliant with electrical installation regulations, must be fitted.
-
Take special care when perforating walls or ceilings and ensure that there are no hidden electrical cables, pipes, metal beams, etc., as perforating them could cause great damage, short circuits, or the transmission of noise and vibrations.
-
IMPORTANT: Before connecting the appliance to the mains, make sure the current is first turned off (differential or circuit breaker on the general electrical panel of the house).
-
Hood and conduit installation must comply with regulations on ventilation of closed spaces. More specifically, the exhausted air must not be led through a conduit that is used for exhausting fumes from other appliances using gas or other fuels (central heating installations, etc.).
-
Negative pressure in the premises must not exceed 0.04 bar. This will allow the hood to operate in optimum conditions. To achieve this, it is necessary to have a permanent entry of fresh air to avoid air stagnation, it is recommended to have a ventilation grille for this purpose. Doors and windows are not enough.
-
Attention! When the hood is in operation “in suction” at the same time as a heating system that depends on ambient air (gas, oil, coal boiler, chimney, etc.), take special care to avoid the hood absorbing air needed for combustion, this could cause dangerous accumulations of carbon monoxide in the premises or home, which could be deadly. If the extractor hood is installed together with a combustion appliance such as a boiler, chimney, or local heating, the manufacturers of these appliances must be contacted to ensure optimum and risk-free operation.
-
The electrical power supply must be stable and meet the electrical requirements of the appliance (see the nameplate of the appliance). If the power supply is unstable, with variations in voltage, current, surges, cuts, electrical storms, etc., the hood could malfunction and even be damaged, in which case repairs will not be covered by the guarantee. If any of these things happen, disconnect the hood and contact an electrician or your electrical company to solve the problem.
-
To avoid hazards, it is forbidden to manipulate the appliance. If the power cable is damaged it must be replaced by the manufacturer through an authorized technical service. Any repairs that involve manipulating the appliance or its components must only be done by an authorized technical service.
-
Improper and unauthorized handling of the hood, as well as modifying, cutting, or perforating the body, structure, motor, or wiring of the hood are expressly forbidden. In case of any of the above, the guarantee will be automatically void and the manufacturer will not be held liable for any possible harm or damages.
-
The hood is an electrical appliance for fume extraction and must not be used as a support for objects or utensils.
-
The LED lamps can not be manipulated by the user as there are risks of electric shock, handling, maintenance or replacement is a task reserved exclusively for official technical assistance service or authorized specialist installer.
-
With the aim of constantly improving our products, we reserve the right to modify their functional characteristics or their appearance.
It must be taken into account and provided that the hood and peripherals must
have easy and safe access for possible maintenance or repair tasks of the
official Pando technical service (SAT). The guarantee will NOT cover the
costs and means necessary for access to a product that does not meet these
conditions. In the event that the product is not easily accessible or safe, a
criterion that will be issued by SAT in its initial inspection, it will be the
responsibility of the client to place the means and assume the necessary costs
so that the SAT can perform the intervention adequately.
TOOLS NEEDLE
DIMENSIONS
CHANGE ENGINE POSITION
INSTALLATION
| 
---|---
| 
---|---
| 
---|---
| 
---|---
CONTROL PANEL
A: Light switch On/Off
B: Reduce speed / OFF motor
C: Luminous telltale
D: ON motor/ increase speed
E: 10-minute timer
If the electrical power supply to the product is cut, 15 seconds are needed
for self-diagnostics after the functions are restored. In the meanwhile, its
operation may be incorrect.
The products are endowed with an electronic device that allows the automatic
switching off after 4hours of working from the last operation
MAINTENANCE
After 30 hours of work, the push button control panel will signal the
saturation of the grease filter by lighting all the buttons. Press the timer
button to reset.
The grease filter needs cleaning by regular hand-washing or in dishwashers
every two months at least or depending on its use.
ACTIVATED CARBON FILTER (FCLR), WASHABLE AND RE-TRIGGERABLE. (OPTIONAL)
**LED LIGHTING AND FEATURES
**
ATTENTION!
LED type lights involve a complex manipulation in addition to an air
connection involving an internal connector risk of electric shock, therefore
this type of handling must be done by the Pando official technical service or
a qualified and authorized professional. The manufacturer will not be liable
for any damage caused by the mishandling of the LED lights by unauthorized
personnel.
MANTENIMIENTO
ILUMINACION Y CARACTERISTICAS LED
INOXPAN S.L.
NOTES: ___
EXCLUSIVE PRODUCT CLEANER, POLISH AND STAINLESS PROTECTOR
INOX PAN DO, Reference 1059.
PROPERTIES: Degreaser is especially recommended for polishing stainless
steel surfaces. with its complex formula based on paraffin, it leaves an
invisible film that acts as a protector and makes it shine.
APPLICATIONS: Cleans, polishes, and evens out stainless steel surfaces of
extractor hoods and stainless steel kitchen furniture.
INOXPAN S.L.
Pol. Ind. El Cros
Av. El Molí de les Mateves,11
Apdo. Correos nº 21
08310 ARGENTONA
(Barcelona – Spain)
Tel. +34 93 757 94 11
Fax +34 93 757 96 53
www.pando.es
com.pando@pando.es
Export: export@pando.es
Tel. 902 41 55 11 
http://www.pando.es
Calidad UNE-EN ISO 9001:2015
The International Certification Network Quality Management System ISO
9001:2015
660066400184. V21.1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>