Hunter 19847 Hepburn Painted Modern Brass Glam Opal Glass Globe LED Mini Pendant Light Instruction Manual
- June 9, 2024
- Hunter
Table of Contents
Hunter 19847 Hepburn Painted Modern Brass Glam Opal Glass Globe LED Mini
Pendant Light
TOOLS NEEDED
PRODUCT DESCRIPTION
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
Hardware Service Kit
Glass
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap nuts (D) from mounting screws (C). Place the mounting plate (A) over the junction box so that mounting screws (C) and nuts (F) extend out away from the ceiling. Depending on the placement of your junction box the position of mounting screws (C) may need to be adjusted to allow the canopy to be flush with the ceiling. Adjust the position of mounting screws (C) so that mounting screws (C) can be exposed 5-6 mm after passing through the canopy (H) to properly fit the cap nuts. Mounting screws (C) can be adjusted by loosening nuts (F) and loosening or tightening mounting screws (C). Once the ideal position of mounting screws (C) has been confirmed, tighten nuts (F) on mounting screws (C) under the mounting plate to ensure that mounting screws (C) are in place. Pull the house wires through the center of mounting plate (A). Secure mounting plate (A) to the junction box by tightening the screws (G).
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (K), and 1 6-inch rod (L) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the downrods may be required). Screw rod onto threaded post (O) on the fixture. Pull the fixture wires through the top of the canopy (H). Screw the top rod to hang straight (J) of canopy (H).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Secure
the screw collar loop (S) into mounting plate (A). Attach the fixture’s wires
to the power supply wires from the junction box. Connect black to black
(live); white to white (neutral); grounding to grounding (green or copper).
Twist the ends of the wire pairs together. Then, twist on a wire connector.
Make sure all twists are in the same direction. Loop fixture’s ground wire
around grounding screw (B) and tighten. If there is no ground wire (green or
copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (H) to mounting plate (A) and position mounting screws (C) so that they protrude through the openings of canopy (H). Secure canopy (H) in place with cap nuts (D). Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Unscrew ring (M) from threads (P) and slide the hood (N) up the rod to expose metal bracket (Q). Angle glass (R) over metal bracket (Q) one side at a time making sure glass (R) is level and resting on the lower notches of metal bracket (Q). Then slide hood (N) back down over the glass and tighten the ring (M) onto threads (P) to secure the hood (N) and glass (R). Remove the glass before maintenance. Turn on the power and test the fixture. Your installation is now complete.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.