Hunter Gatz Glamour Vanity Light Instruction Manual
- October 27, 2023
- Hunter
Table of Contents
Hunter Gatz Glamour Vanity Light Instruction Manual
Product Overview
Specifications
1 Light Wall Sconce
Fixture weight ±2 lbs:
Peso ±2 lb:
Poids fixe ±2 lbs:
2.4 lbs (1.09 kg)
Hardware Service Kit
| Part # | Model | Finish |
|---|---|---|
| KE18101L24 | 19680 | Palm Gold |
| KE18101214 | 19681 | Brushed Nickel |
Glass
| Part # | Model | Type |
|---|---|---|
| KE29301147 | 19680 19681 | Clear Fluted Glass |
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning installation of the lighting fixture.
Here are the tools you’ll need to complete your installation:
PREPARING FOR INSTALLATION CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the wall, including
the old mounting bracket. Remove the new mounting bracket assembly from the
bag.
Remove cap nuts (G) from mounting screws (D). Place the mounting plate (A)
over the junction box so that mounting screws (D) and nuts (C) extend out away
from the wall. Adjust the position of mounting screws (D) so that mounting
screws (D) can be exposed 5-6 mm after passing through the back plate (F) to
properly fit the cap nuts. Mounting screws (D) can be adjusted by loosening
nuts (C) and loosening or tightening mounting screws (D). Once the ideal
position of mounting screws (D) has been confirmed, tighten nuts (C) on
mounting screws (D) on the front of the mounting plate to ensure that mounting
screws (D) are secure. Pull the house wires through the center of mounting
plate (A). Secure mounting plate (A) to the junction box by tightening the
screws (B).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Place the fixture’s back plate (F) over the mounting screws (D) so the threads protrude through the holes on the front of the back plate. Tightly screw the cap nuts (G) onto the mounting screws (D) until the back plate (F) of the fixture is snugly against the wall. Lift the glass (I) and align the notches in the glass with the tabs in the lamp cup (H). Attach the glass by lifting and turning clockwise one third of a full turn of the glass until it stops. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
WARNING
GLASS FALL HAZARD
To prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>