Pro-Ject AUDIO SYSTEMS Power Box S3 Phono Instructions
- June 9, 2024
- Pro Ject AUDIO SYSTEMS
Table of Contents
Pro-Ject AUDIO SYSTEMS Power Box S3 Phono
INSTRUCTIONS FOR USE
Dear music lover,
Thank you for purchasing a Pro-Ject Audio Systems Power Box S3 Phono.
In order to achieve maximum performance and reliability you should study these
instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
Safety Instructions
AC outlet voltages vary from country to country. Before connecting to the
mains, make sure that the voltage in your area meets the voltage requirements
printed on the power supply.
Never handle the device while your hands are wet or damp.
Avoid letting liquids enter the device. Never place any item containing
liquid, such as a flower vase on or near the device. Never spill any liquid on
the device. Never place any naked flame sources, such as lighted candles on or
near the device. The product shall not be used in damp or wet locations, next
to a bathtub, sink, swimming pool or any other similar conditions.
Using the product
Power Box S3 Phono is designed to power a wide range of DC-powered Pro-Ject turntables with 15V and phono preamplifiers with 18V.
Make all connections whilst the Power Box S3 Phono is switched off or disconnected from the mains.
Interconnection cables are included in the packaging. Original power supplies are no longer required. Ensure that you use the correct cable for your device: The cables are marked on both ends. In case of any doubts, consult user manuals of all connected products or ask your dealer.
Main power switch
The toggle switch on the front panel turns the unit on or off. The blue LED above the switch shows that the unit is switched on.
Led indicators
The LEDs Turntable and Phono Stage on the front indicate that a device is connected.
All Pro-Ject Phono Boxes with 18V can be powered with the Phono Stage
Output.
All Pro-Ject Turntables with 15V DC input can be powered with the Turntable
Output, except RPM5 and higher, X2 and higher, Signature 10 & 12.
Technical specifications Pro-Ject Power Box S3 Phono
Input Power supply: 115V/230V AC
Output voltage/ripple 1 x 15V ±0,5%
Output voltage/ripple 1 x 18V ± 0,5%
Output current: both outputs combined max. 1000 mA
Dimension ( W x D x H ): 103 x 37 x 106 mm
Weight: 370 g
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.
Copyright, trademarks
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems Copyright © 2022. All
rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
Declaration of Conformity
We, Canor spol. s r. o. Družstevná 13925/39 08006 Prešov
Slovakia (manufacturer) and Pro-Ject Audio Systems a division of Audio Tuning
GmbH Margaretenstrasse 981050 Vienna, Austria (distributor) declare under our
responsibility that the product is in conformity with the provisions of
Directives:
2014/35/EU including amendments
2014/30/EU including amendments
STN EN 62368-1:2015 – Safety
STN EN 55035:2018 – Electromagnetic compatibility of multimedia equipment
– Immunity requirements
STN EN 55032:2015 – Electromagnetic compatibility of multimedia equipment
– Emission requirements
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>