Pro-Ject AUDIO SYSTEMS T2 Audiophile Turntable Instruction Manual

July 16, 2024
Pro Ject AUDIO SYSTEMS

INSTRUCTIONS FOR USE
Pro-Ject T2

T2 Audiophile Turntable

Dear Music Lover,
Congratulations and thank you for choosing Pro-Ject Audio Systems record player.
Your T2 turntable has been handcrafted and rigorously tested by skilled technicians to give you years of enjoyable, trouble-free service.
If you require additional assistance, please contact your dealer.
Important:
Your turntable was shipped partially disassembled to avoid damage to sensitive parts. Please check immediately to ensure that neither the packaging nor the device was damaged in transit. If you are missing parts or if the unit is damaged, please do not operate it and contact your dealer.
Please do your part to help protect the environment:
Disposal of packaging material:
Pro-Ject packaging is carefully designed to protect your component from damage during transit, and you are strongly urged to keep the original packaging to safely ship or otherwise transport your turntable in the future. However, the packaging materials were chosen to be environmentally friendly, so if you must discard the packaging, please recycle it.

GENERAL INFORMATION

Controls, features and connections

  1. PLATTER & FELT MAT
  2. CHASSIS
  3. SPEED CONTROL BUTTON
  4. MOTOR WITH PULLEY
  5. DRIVE BELT
  6. SUB-PLATTER
  7. TONEARM COUNTERWEIGHT
  8. ANTI-SKATING ADJUSTMENT SCREW WITH SCALE
  9. TONEARM REST / REMOVABLE TRANSPORT LOCK
  10. TONEARM LIFT LEVER
  11. TONEARM TUBE
  12. HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED CARTRIDGE
  13. LID
  14. LID HINGES
  15. HINGE FASTENERS
  16. POWER SUPPLY SOCKET
  17. RCA OUTPUT BOX

Accessories

  1. SINGLE ADAPTOR
  2. ALLEN KEY 1,5mm
  3. COUNTERWEIGHT no. 105 (FOR CARTRIDGE WEIGHT 5 – 11.5g)
  4. TWO-POINT CARTRIDGE ALIGNMENT PROTRACTOR
  5. CONNECTION CABLE (CONNECT IT E RCA)
  6. SETUP GUIDE
  7. UNIVERSAL POWER SUPPLY

Pro Ject AUDIO SYSTEMS T2 Audiophile Turntable -
Accessories

SETUP

  1. Platter and drive belt installation
    Please remove drive belt from accessories box and install it as shown in the following illustration. Put the felt mat on the top of the platter.Pro Ject
AUDIO SYSTEMS T2 Audiophile Turntable - platter

  2. Cartridge installation, stylus exchange

  • If you purchased this turntable in a package that included the cartridge, this has already been done for you.
    Install the cartridge into the aluminium headshell, using the appropriate hardware included with your cartridge. All cartridges with half inch mounting holes can be fitted.
    Connect the cartridge as indicated below:• White| left channel L+
    ---|---
    • Red| right channel R+
    • Green| right channel R-
    • Blue| left channel L-

For correct cartridge alignment, use the two-point cartridge alignment protractor provided with your T2 ccessories. If unfamiliar with two-point setup, please refer to your dealer.
A damaged or worn stylus may harm your record collection and should be replaced.
Please remove stylus protection before pulling the stylus from the cartridge and replace for a new one.
Stylus type is exchange for pre-mounted cartridge Sumiko Rainier: Stylus Sumiko Rainier. If in doubt, consult your local dealer or distributor.

  1. Vertical Tracking Force setting (VTF)
    The T2 Super Phono comes with the counterweight already assembled on the tonearm, and the tracking force is factory pre-adjusted.
    To adjust or fine tune the tracking force manually, loosen the hexagonal screw on top of the counterweight (7) using the allen key provided. Remove the stylus protection cover and place the stylus pressure gauge onto the platter. To set the required VTF, lower the tonearm lift lever (10) as indicated in the illustration and place the tip of the stylus on one of the points on the scale. For example, the Sumiko Rainier requires 20mN of tracking force, so place the stylus on the 20mN point.
    If the stylus gauge becomes level when the tonearm is lowered down onto the desired point, then the correct pressure has been achieved. However, if there is insufficient or excessive pressure, the gauge will either not move or tilt down. To adjust the amount of pressure, carefully move the counterweight (7) along the support rod, until the stylus pressure is sufficient to raise the pressure gauge to the level position. Moving the counterweight (7) away from the cartridge will reduce pressure and towards will increase pressure. Finally secure the counterweight (7) using hexagonal key provided.Pro Ject AUDIO
SYSTEMS T2 Audiophile Turntable - level

  2. Maintenance and cleaning
    Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.
    If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.

  3. Switching on and off, changing replay speed
    The turntable is equipped with a three-position switch for ON/OFF and electronic speed change. To play records at 33 rpm. press this switch (3) to the rear side. To play records at 45 rpm. press this switch (3) to the front side as shown on illustration below.Pro Ject AUDIO SYSTEMS T2 Audiophile
Turntable - speed

  4. Anti-skating
    The anti-skating force is pre-adjusted from the factory corresponding to the tracking force.
    Sumiko Rainier recommended tracking force 20mN = anti-skating set to 2 (middle position).
    You can adjust the anti-skating by rotating the anti-skating setting screw to the left or right.Pro Ject AUDIO SYSTEMS T2 Audiophile Turntable - Anti-
skating

  5. Connection to the amplifier
    Connect the tonearm cables to the Phono input (sometimes labelled gram, disc, or RIAA) on your amplifier.
    Ensure that the phono input offers the correct matching and amplification for the type of cartridge used. Line inputs (such as CD, Tuner, Tape, or Video) are not suitable. Be sure to connect the left and right channels correctly. The right channel is usually marked red, and the left channel is black or white. Check the manual supplied with your amplifier for relevant information. An earthing wire may be connected to the screw terminal on your amplifier if you encounter hum problems when using the record player. If your amplifier does not have an input suitable for phono cartridges, you will require a separate phono amplifier stage for MM or MC cartridges, which is then connected between the record player and a free line level input on the amplifier.
    For detailed product information regarding Pro-Ject Audio interconnect cables and phono amplifiers, please refer to the Pro-Ject website at www.project- audio.com.

The recommended load impedance for the factory fitted cartridge is: 47kohms /MM-input

Technical specifications Pro-Ject T2 / Pro-Ject 9’’

Nominal speeds 33/45 r.p.m.
Speed variance 33: ±0.60% 45: ±0.50%
Wow and flutter 33: ±0.19% 45: ±0.17%
Signal to noise -67dB
Effective tonearm mass 9.5g
Effective tonearm length 9″ (230mm)
Overhang 22 mm
Power consumption 4.5W
Power input 15V/ 0.8 A DC, universal power supply
Dimensions (W x H x D) 457 x 134 x 335mm
Weight 5.5kg
Dimensions packaging (W x H x D) 542 x 300 x 412mm
Weight incl. packaging 8.5kg

Technical specifications MM-Cartridge Sumiko Rainier

Frequency range 15-25.000Hz
Channel separation 25dB/1kHz
Output voltage 5mV
Recommended load impedance 47kohms/amplifier connection – MM-input
Compliance/stylus type 10×10-6cm/dyn @ 100Hz– elliptical
Recommended tracking force 20mN
Capacitance 100pF – 200pF
Weight 6.5g

Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore, the following list of common fault symptoms is included.
The platter doesn’t turn although the unit is switched on:
The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
Correct input not selected at amplifier.
Amplifier is not switched on.
Amplifier or speakers are defective or muted.
No connection to the loudspeakers.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier.
Needle or cantilever damaged.
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason, we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt.
Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.
Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems Copyright © 2024. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
Declaration of Conformity
We, SEV Litovel, s r.o.
Palackého 1160/34
78401 Litovel
Czech Republic
(manufacturer) and
Pro-Ject Audio Systems a division of Audio Tuning GmbH
Margaretenstrasse 98
1050 Vienna,
Austria
(distributor)
declare under our responsibility that the product is in conformity with the provisions of Directives:
2014/35/EU including amendments
2014/30/EU including amendments
2014/53/EU including amendments
The following harmonised standards were applied:
Health: EN62479:2010
Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, EN62368-1:2014/A11:2017,
EN61558-1:2005/A1:2009, EN61558-2-16:2009/A1:2013
EMC: EN301489-1 V2.2.0: 2017-03, EN301489-17 V3.2.0:2017-03, EN55032:2015, EN55035:2017,
EN61000-3-2:2014, EN61000-3-3:2013
Radio Spectrum: EN300328 V2.1.1 (2016-11)
Pro-Ject Audio Systems a division of Audio Tuning GmbH
1050 Vienna, Austria, Margaretenstrasse 98
info@project-audio.com Pro Ject AUDIO
SYSTEMS T2 Audiophile Turntable - LID

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals