Hilti HIT-HY 100 Injectable Adhesive Anchors

INTRODUCTIONS

Adhesive anchoring system for rebar and anchor fastenings in concrete.
Read the safety precautions, safety data sheet, and the product information before use.
Read the safety precautions and the product information of the accessories before use.

HAS, HIT-V

HIT-V

Ø d [inch]

| Ø d0 [inch]| hef [inch]| Ø df [inch]| hs [inch]| Tinst [ft-lb]| Tinst [Nm]
---|---|---|---|---|---|---
3⁄8| 11⁄16| 4 3⁄8| 7⁄16| 3⁄8…15⁄16| 15| 20
1⁄2| 7⁄8| 5| 9⁄16| 1⁄2…1 3⁄16| 30| 41
5⁄8| 1 1⁄8| 6 3⁄4| 11⁄16| 5⁄8…1 1⁄2| 60| 81
3⁄4| 1 1⁄4| 8 1⁄8| 13⁄16| 3⁄4…1 7⁄8| 100| 136

HIS-N

Ø d [inch]| Ø d0 [inch]| hef [inch]| Ø df [inch]| hs [inch]| Tinst [ft- lb]| Tinst [Nm]
---|---|---|---|---|---|---
3⁄8| 11⁄16| 4 3⁄8| 7⁄16| 3⁄8…15⁄16| 15| 20
1⁄2| 7⁄8| 5| 9⁄16| 1⁄2…1 3⁄16| 30| 41
5⁄8| 1 1⁄8| 6 3⁄4| 11⁄16| 5⁄8…1 1⁄2| 60| 81
3⁄4| 1 1⁄4| 8 1⁄8| 13⁄16| 3⁄4…1 7⁄8| 100| 136
Ø d [mm]| Ø d0 [mm]| hef [mm]| Ø d f [mm]| hs [mm]| Tinst [Nm]
---|---|---|---|---|---
M8| 14| 90| 9| 8…20| 10
M10| 18| 110| 12| 10…25| 20
M12| 22| 125| 14| 12…30| 40
M16| 28| 170| 18| 16…40| 80
M20| 32| 205| 22| 20…50| 150

Rebar

US Rebar

d| Ø d0 [inch]| hef [inch]
---|---|---

3| 1⁄2| 2 3⁄8…7 1⁄2

4| 5⁄8| 2 3⁄4…10

5| 3⁄4| 3 1⁄8…12 1⁄2

6| 7⁄8| 3 1⁄2…15

7| 1| 3 1⁄2…17 1⁄2

8| 1 1⁄8| 4…20

9| 1 3⁄8| 4 1⁄2…22 1⁄2

10| 1 1⁄2| 5…25

CA Rebar

d| Ø d0 [inch]| hef [mm]
---|---|---
10 M| 9⁄16| 70…226
15 M| 3⁄4| 80…320
20 M| 1| 90…390
25 M| 1 1⁄4| 101…504
30 M| 1 1⁄2| 120…598

Rebar

EU Rebar

Ø d [mm]| Ø d0 [mm]| hef [mm]
---|---|---
8| 12| 60…160
10| 14| 60…200
12| 16| 70…240
14| 18| 75…280
16| 20| 80…320
18| 22| 85…360
20| 25| 90…400
22| 28| 95…440
24| 32| 96…480
25| 32| 100…500
26| 35| 104…520
28| 35| 112…560
30| 37| 120…600
32| 40| 128…640

• Manual hand pump option only valid under ETA approvals (ETA 14/0001 and ETA 14/0009)

Adhesive anchoring system for rebar and anchor fastenings in concrete.

Safety instructions

Contains: Hydroxypropyl methacrylate(A), boric acid (A), dibenzoyl peroxide(B)

Danger

• H317 May cause an allergic skin reaction. (A,B)
• H319 Causes serious eye irritation (A)
• H360 May damage fertility or the unborn child. (A)
• H400 Very toxic to aquatic life. (B)
• P262 Do not get in eyes, on skin, or on clothing.
• P280 Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352 IF ON SKIN: Wash with plenty of soap and water.
• P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
• P337+P313 If eye irritation persists: Get medical advice/attention.

Disposal considerations

Empty packs:

• Leave the mixer attached and dispose of via the local Green Dot recovery system
• or EAK waste material code: 150102 plastic packaging

Full or partially emptied packs

• Must be disposed of as special waste in accordance with official regulations.
  • EAK waste material code: 08 04 09* waste adhesives and sealants containing organic solvents or other dangerous substances.
  • or EAK waste material code: 20 01 27* paint, inks, adhesives and resins containing dangerous substances.

Content: 330 ml / 11.1 fl.oz. 500 ml / 16.9 fl. oz
Weight: 575g / 20,3oz 880g / 31,0oz

Warranty

Refer to standard Hilti terms and conditions of sale for warranty information.

Failure to observe these installation instructions, use of non-Hilti anchors, poor or questionable base material conditions, or unique applications may affect the reliability or performance of the fastenings.

Product Information

• Always keep these instructions together with the product even when given to other persons.
• Review the MSDS before use.
• Check expiration date: See imprint on foil pack manifold (month/year). Do not use expired product.
• Foil pack temperature during usage: 0 °C to 40 °C / 32 °F to 104 °F.
• Base material temperature at time of installation: between -10 °C and 40 °C / 14 °F and 104 °F.
• Conditions for transport and storage: Keep in a cool, dry and dark place between 5 °C and 25 °C / 41 °F and 77 °F.
• For any application not covered by this document / beyond values specified, please contact Hilti.
• Partly used foil packs must remain in the cassette and has to be used within 4 weeks. Leave the mixer attached on the foil pack manifold and store within the cassette under the recommended storage conditions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive.

NOTICE
Improper handling may cause mortar splashes.

• Always wear eye protection, gloves and protective clothes during installation.
• Never start dispensing without a mixer properly screwed on.
• Attach a new mixer prior to dispensing a new foil pack (ensure snug fit).
• Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not modify the mixer in any way.
• Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes).

Poor load values / potential failure of fastening points due to inadequate borehole cleaning.

• Hilti hollow drill bits TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity (volumetric flow rate) as specified in the accessory table.
• Holes should be drilled with a rotary hammer drill, using drill bits that comply with ANSI B212.15-1984.
• The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection.
• For blowing out the borehole – blow out with oil free air until return air stream is free of noticeable dust.
• For brushing the borehole – only use specified wire brush. The brush must resist insertion into the borehole – if not the brush is too small and must be replaced.
• Before inserting anchor/rebar into borehole, mark and set anchor/rebar to the required embedment depth.
• Anchor rods/rebar shall be free of dirt, grease, oil, and other contaminants.

Ensure that boreholes are filled from the back of the borehole without forming air voids.

• The annular gap between the anchor/rebar and the borehole shall be filled completely with no gaps.
• If necessary use the accessories / extensions to reach the back of the borehole.
• For overhead applications use the overhead accessories HIT-SZ and take special care when inserting the fastening element. Excess adhesive may be forced out of the borehole. Make sure that no mortar drips onto the installer.

Not adhering to these setting instructions can result in failure of fastening points!

Hilti Argentina S.R.L.
Profesor Manuel García 4760
B1605 BIB – Munro
AR-Buenos Aires
Tel +54 11 4721 4400

Hilti (Aust.) Pty. Ltd.
Level 5, 1G Homebush Bay Drive
Rhodes N.S.W. 2138
Tel +61 2 8748 1000

Hilti do Brasil Comercial Ltda.
Av. Ceci, 426-Centro Empresarial
Tamboré
06460-120 Barueri, SP
Tel +55 11 4134 9000

Hilti (Canada) Corp.
2360 Meadowpine Boulevard
Mississauga, Ontario L5N 6S2
Tel +1 905 813 9200

Hilti Chile Ltda.
Av. Apoquindo 4501, piso 13
Las Condes 7550000
Santiago
Tel +562 655 3000

Superba S.A.
200 Mts. Oeste de Matra la Uruca
CR-San José
Tel +506 2255 1044

Hilti Mexicana, S.A. de C.V.
Jaime Balmes 8, Oficina 102, 1er Piso
Col. Los Morales Polanco
Del. Miguel Hidalgo
MEX-Mexico City 11510
Tel +5255 5387-1600

Hilti Distribution Ltd.
Business park ZAO „Greenwood“
MKAD 69 km, bldg. 3
Krasnogorsky rajon, p/o Putilkovo
RU-143441 Moskau region
CS: • +7 495 792 52 52

Hilti, Inc.
7250 Dallas Parkway, Suite 1000
US-Plano, TX 75024
Tel +1 918 872 3000

0756
Hilti AG
FL-9494 Schaan
Hilti Werke
14
0756-CPR-0612
ETA-14/0001
ETAG001-1, -5
TR 23

0756
Hilti AG
FL-9494 Schaan
Hilti Werke
14
0756-CPR-0613
ETA-14/0009
ETAG001-1, -5
Option 1

www.hilti.group Made in Germany
Hilti = registered trademark of Hilti Corporation, Schaan, Liechtenstein
© 2018
Right of technical changes reserved S.E. & O,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>