ninebot WF-200 Smart Dashboard User Manual
- June 9, 2024
- Ninebot
Table of Contents
ninebot WF-200 Smart Dashboard
Product Overview
Product Introduction
This product is installed in the dashboard as part of the electric assisted
kick scooter, See the above picture.
When the user is actually using the kick scooter, this product can be used for
swiping the card and charging the mobile phone, and when using time, the user
will not touch the product and should keep a certain distance, at least 20cm.
More introduction
This product offers a configurable charging mode that supports 15W.15W power supply meets WPC QI standard RX. Supports foreign body detection, if there is a foreign body, as a metal conductive material, between the transmitter and the receiver, the transmitter is off. Place the mobile phone in the wireless charging tray, charge the mobile phone, and stop charging after removing the mobile phone. Magnetic card into the NFC induction area when the card operation!
**Product parameters
**
- Name: Ninebot Smart Dashboard
- Model: WF-200
- Color: black
- Input voltage: DC 18V
- Input current: 1.5A(Max)
- Operating Temperature: 0–40°C
- Storage Temperature: -20–70°C
Characteristics
- Meet the WPC QI standard
- Support foreign body detection
- RoHS compliance
FUNCTION SPECIFICATIONS
Wireless Charging
Rated power| 15W
Frequency band(kHz)| 115~145
Modulation| ASK
Antenna type| Coil Antenna
NFC
Frequency band(MHz)| 13.56MHz
Modulation| ASK
Antenna type| Coil Antenna
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING
When using this product, basic precautions should always be followed,
including the following:
- Read all the instructions before using the product.
- To reduce the risk of injury, close supervision is necessary when the product is used near children.
- DO NOT put fingers or hands into the product.
- DO NOT use this product if the flexible power cord or output cable is frayed, has broken insulation, or any other signs of damage.
Meaning of Symbols and Marks
This product conforms to the applicable EC Directives.
WARNING-It is not permitted to dispose of this product as normal
household waste. Ensure that the product is recycled in
accordance with local legal requirements.
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
This equipment complies with relevant RF radiation exposure limits set forth
for a public/uncontrolled environment. This equipment should be installed
and/or operated with a minimum distance 20cm between the radiator and your
body.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Any changes or modifications not expressly approved by Ninebot (Changzhou) Tech Co., Ltd. for compliance could void the user’s authority to operate this equipment.
IC Statement
This device complies with CAN ICES-003(B) / NMB-003(B).
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
ISED Warning
This equipment complies with relevant RF radiation exposure limits set forth
for a public/uncontrolled environment. This equipment should be installed
and/or operated with a minimum distance 10cm between the radiator and your
body.
Installation
As shown in the figure above, fix the Onboard 15W Wireless Charging on the top
of the scooter with screws and connect the corresponding wiring harness.
Power on the Kick Scooter and check the battery level and other display shown
on the equipment.