Knightsbridge FLPA150 230V IP65 150W LED Floodlight Instruction Manual
- June 9, 2024
- Knightsbridge
Table of Contents
Knightsbridge FLPA150 230V IP65 150W LED Floodlight
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end user for future reference and maintenance.
These instructions should be used to aid installation of the following
products:
FLPA100 / FLPA100D / FLPA150 / FLPA150D / FLPA200 / FLPA200D
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
- Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
- This product is Class I and must be earthed
- This product is IP65 rated
INSTALLATION
Note – If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
- Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP rated junction boxes should be used where required
- Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the fitting
- Using the bracket as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any gas/water pipes or electrical cables
- Remove the four screws on the access plate at the rear of the fitting to expose the terminal block (see Fig. 1)
- Feed the cable through the compression gland on the rear of the access plate. A drip loop should be left on the incoming mains cable (see Fig. 2)
- Connect the luminaire to the mains supply ensuring the correct polarity is observed: L – Live (brown), E – Earth (green/yellow), N – Neutral (blue) (see Fig. 3)
- Replace the access plate and screws ensuring gasket is in place then tighten the compression gland ensuring a tight seal to maintain the IP rating
- Fix the bracket to the surface using suitable screws
- Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high
voltage or insulation resistance testing. Irreparable damage will occur if
this instruction is not followed. This product is not suitable for
installation in or near a coastal or marine environment.
GENERAL
This product contains a light source of energy efficiency class E to Regulation
(EU) No. 2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and a non-replaceable
control gear.
Clean the external surfaces with a damp cloth using a mild solution of
detergent and warm water only, do not use aggressive cleaning products or
solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this
luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its
life.
Please see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end
of its life. Check local authorities for where facilities exist
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice.
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road,
Dunstable LU5 4LT, www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasseler Lohweg 18, 40547
Düsseldorf, Germany
Email: eprel@nnuks.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>