ergotron 45-496-224 MXV Desk Dual Monitor Arm Instruction Manual
- June 9, 2024
- ERGOTRON
Table of Contents
ergotron 45-496-224 MXV Desk Dual Monitor Arm
For the latest User Installation Guide please visit: www.ergotron.com
Safety
Hazard Symbols Review
These symbols alert users of a safety condition that demands ention. All
users should be able to recognize and understand the signifi cance of the
following Safety Hazards
if encountered on the product or within the documentation. Children who are
not able to recognize and respond appropriately to Safety Alerts should not
use this product without adult supervision!
NOTE
A NOTE indicates important information that helps you make before use of this
product.
CAUTION
A CAUTION indicates either potential damage to hardware or loss of data and
tells you how to avoid the problem.
WARNING
A WARNING indicates either potential for property damage, personal injury, or
death.
ELECTRICAL
An Electrical indicates an impending electrical hazard which, if not avoided,
may result in personal injury, fi re and/or death.
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the toll range of motion and stay where you set it. f movements are too easy or detect or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Warning:
Because mounting surface materials can vary widely, it is imperative that you
make sure mounting surface is strong enough to handle mounted product and
equipment.
Attention:
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury
CAUIION: DO NOT rotate monitor past rear edge of desk. Doing so will ereate an unstable situation and may cause equipment damage or personal injury.
Features & Specifications
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
Components
Tools needed
Optional locking feature (customer supplied lock)
How to replace rotation stop screws (Arms must be straight up)
ATTACH DISPLAY
NOTE: VESA plate will only accept 75mm or 100mm VESA pattern
WARNING! Stored Energy Hazard: The Riser mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the Riser has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
NOTE Leave enough slack in cable to allow full range of motion.
Caution
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury.
Adjustment Step
Important! You will need to adjust this product atter installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Lift – Up and down
Tilt – Forward and Backward
Liȋ – Up and down
Increase Lift Strength If the mounted weight is too heavy or this product does not stay up when raised, then you’ll need to Lincrease Lift Strength:
Decrease Lift Strength If the mounted weight is too light or this product does not stay down when lowered, then you’ll need to decrease Lift Strength:
CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.
Tilt – Forward and Backward
Increase Friction
If this product moves too easily, then you’ll need to increase friction
Decrease Friction
If this product is too diffi cult to move, then you’ll need to decrease
friction: 
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit:
htto:/lcontact.eraotron.com
NOTE: When contacting customer service, reference the serial number
www.ergotron.com|USA: 1-800-688-8458| Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: japansupport@ergotron.com
© 2016 Ergotron, Inc. All rights reserved.
While made Ergotron, process makes of translation every from provide accurate
to another language), information incidental, installation consequential
damages of any not nature resulting for from furnishing errors instruction
omissions and performance of connection. Ergo iron, eves conges in product
Design and product Deonta to users For transmitted in any form or by any
means, electronic, mechanical, photocopying, recording or otherwise without
the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan, Minnesota,
55121, USA Patents Pending and Patented US.& Foreign is a registered trademark
of Ergotron.Inc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>