geemarc Voyager 2 Travel Alarm and Shake User Guide

geemarc Voyager 2 Travel Alarm and Shake

“Please refer to our website: www.geemarc.com for an up-to-date user guide, as there may be important updates and changes you need to be aware of ”

DESCRIPTION OF THE PRODUCT

BATTERY INSTALLATION

Your clock requires 1 x AAA and 2 x AA alkaline batteries (included) to operate.

1. Place your unit face down on a flat surface.
2. Press the latch and remove the battery cover at the back of your unit.
3. Insert 1 x AAA and 2 x AA new alkaline batteries into the battery compartment by observing the correct “+” and “- “polarity.
4. Replace the battery cover.

TO SET TIME AND THE SNOOZE DURATION

1. Press and hold SET and the hour digits “0” flash. Press TEST/ or  to set the time in hours (hold TEST/ or to advance rapidly).
2. Press SET again, and the minute digits “00” flash. Press TEST/ or to set the time in minutes. (hold TEST/ or to advance rapidly).
3. Press SET again, the display shows “24Hr” and flashes. Press TEST/ or to select “12Hr” or “24Hr” time format. There has AM icon to indicate the morning time and a PM icon to indicate the afternoon time.
4. Press SET again, the display shows “05” and flashes. Press TEST/ or to select your snooze time from 5 to 60 minutes.
5. Press SET again or if no key is pressed for approx. 10 seconds to exit the setting mode.

TO SET THE ALARM

(default at 6:00 AM)

1. Press and hold AL SET / SELECT , the AL appears and the alarm’s hour digits flash. Press TEST/ or to set the alarm in hours. (hold TEST/ or to advance rapidly).
2. Press AL SET / SELECT once again, and the alarm’s minute digits flash. Press TEST/ or to set the alarm in minutes. (hold TEST/ or to advance rapidly).
3. Press AL SET / SELECT again , and “HI” flash (vibration at HI level), press TEST/ or select “LO” (vibration at Low level) if needed.
4. Press AL SET / SELECT again , and “HI” flash (Sound at a HIGH level), press TEST/ or select “LO” (Sound at Low level) if needed.
5. Press AL SET/SELECT once again or no button for around 10 seconds to exit the alarm setting mode. Amidst alarm setting, press SET once to exit and return to normal time display mode.

TO SELECT THE ALARM MODE

At normal time display mode, press AL SET / SELECT one at a time to activate the alarm(s), the corresponding alarm indicator(s) on the right side of the time display will be on:

| | | |
---|---|---|---|---
the only sound alarm is activated| only the shaker alarm is activated| only strobe light alarm is activated| both sound and vibration alarms are activated| both strobe light and sound alarm are activated

Press AL SET / SELECT once more to turn off all the alarms, all alarm indicators disappear.
Remark: frequent use of the vibration and flashlight will quickly shorten the battery life.

TO STOP AND RESET THE ALARM TO COME ON THE NEXT DAY
When an alarm is sounding, the corresponding alarm indicator flashes. Press AL STOP once to stop the alarm and reset it to come on the following day. After that, the corresponding alarm indicator stays on the display.
TO USE SNOOZE
When an alarm is sounding, presses once, and the alarm will be stopped temporarily and the corresponding alarm indicator keeps flashing. The alarm will come on again after the set snooze duration is over.
TO USE BACKLIGHT
Press once to activate the backlight for 5 seconds.
TO USE FLASHLIGHT
Press and hold to an active flashlight. Press and hold to de-active the flashlight.
TEST MODE
Press and hold TEST/ Button, strobe light flashing, shaker vibrating, and buzzer sounding for 5 seconds and then stops.

LOW BATTERY ALERT

When the battery level becomes low, a low battery icon will appear on the upper middle of the LCD. Replace batteries with new alkaline batteries.
Remark: frequent use of the vibration alarm will quickly shorten the battery life.

TROUBLESHOOTING

If your clock displays an irrelevant time or does not function properly, which may be caused by electrostatic discharge or other interference, open the battery cover, take out the batteries and reinstall them by observing the correct +/- polarity. Your clock will be reset to default settings and you need to set it again. A low battery level will decrease the vibration and the alarm sound. Once this happens, replace batteries with new ones.

CARE OF YOUR PRODUCT

1. Place your clock on a stable surface, away from sources of direct sunlight or excessive heat or moisture.
2. Protect your furniture when placing your units on natural wood and lacquered finish by using a cloth or protective material between it and the furniture.
3. Clean your unit with a soft cloth moistened only with mild soap and water. Stronger agents such as Benzene, thinner or similar materials can damage the surface of the unit. Make sure the unit is unplugged before cleaning.
4. If the unit is not to be used for a prolonged period, such as a month or longer, remove the batteries to prevent possible corrosion. Should the battery compartment become corroded or dirty, clean the compartment thoroughly and replace the batteries.

SPECIFICATIONS

Default settings

| Time format| 24 hour
Time| 0:00
Alarm| 6:00
Shaker alarm level| Hi
Snooze duration| 05 (5 minutes)
Audible alarm| : up to 75 dB at 1m

GUARANTEE

From the moment your Geemarc product is purchased, Geemarc guarantees it for a period of two years. During this time, all repairs or replacements (at our discretion) are free of charge. Should you experience a problem then contact our helpline or visit our website at www.geemarc.com. The guarantee does not cover accidents, negligence, or breakages to any parts. The product must not be tampered with or taken apart by anyone who is not an authorized Geemarc representative. The Geemarc guarantee in no way limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE RETAINED AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM.
Please note: The guarantee applies to the United Kingdom only.

DECLARATIONS

UKCA Directives: Geemarc Telecom SA hereby declares that this Wake ’n’ shake Voyager is in compliance with the UKCA Directive requirements. The UKCA declaration of conformity may be consulted at www.geemarc.com
Recycling Directives: The WEEE (Waste Electrical and Electronic Equipment) has been put in place for the products at the end of their useful life are recycled in the best way. When this product is finished with, please do not put it in your domestic waste bin. Please use one of the following disposal options:

• Remove the batteries and deposit them in an appropriate WEEE skip. Deposit the product in an appropriate WEEE skip.
• Or, hand the old product to the retailer. If you purchase a new one, they should accept it. Thus if you respect these instructions you ensure human health and environmental protection.

Support

For product support and help visit our website at www.geemarc.com
E-mail: help@geemarc.com
telephone 01707 387602 lines are open 09h00 to 16h00 Mon to Fri 2 rue Galilée, Parc de l’Etoile, 59791 Grande-Synthe Cedex, France

References

• Home - Geemarc UK
• STARTSEITE - Geemarc Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>