COSTCO ARK14100 9 Piece Woven High Dining Fire Set User Guide

COSTCO ARK14100 9 Piece Woven High Dining Fire Set

Safety Instructions

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS?
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the gas supplier equipment.

WARNING: It is UNSAFE to use this product for cooking!

Questions, Problems, Missing Parts? Before returning to your retailer, call our customer service department in the US and Canada at 1-888-383-1932, Monday-Friday, 9 a.m. – 5 p.m Eastern Time. English and French, or you may Email customerservice @agio-usa.com International Regions: Please visit
http://www.agio-usa.com/service-center/costco-international

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

WARNING: Before placing the burner cover on, make sure the firepit has been shut off and the burner has completely cooled down.
Conditions for use of the product: This product is for outdoor use only. Not for commercial use.
WARNING: A parasol shall not be placed on or shall be used with a separate base.
WARNING: For Outdoor Use Only
WARNING: Do Not Burn Wood or any other materials in this firepit.

FOR USE WITH 5KG PATIO GAS PROPANE CYLINDER (NOT SUPPLIED) WITH CLIP-ON CONNECTION OR USE WITH NATURAL GAS AFTER CONVERSION KIT (SUPPLIED) IS INSTALLED.

WARNING: Improper installation, adjustment alteration, service, or maintenance can cause injury or property damage. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment. This appliance must be installed and the gas cylinder stored in accordance with the regulations in force.
WARNING:
USE FACTORY-APPROVED REPLACEMENT PARTS AND ACCESSORIES ONLY. USE OF UNAPPROVED PARTS OR ACCESSORIES CAN VOID THE WARRANTY ON THIS PRODUCT AND RESULT IN A HAZARDOUS CONDITION. PLEASE CONTACT US FOR INFORMATION REGARDING REPLACEMENT HOSES, THERMOCOUPLES, ELECTRODES, IGNITION MODULES, LAVA ROCKS, LOGS, ETC.

IMPORTANT SAFETY INFORMATION

• The appliance area must be kept clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

• Children and adults should be alerted to the hazards of high surface temperatures and kept at a safe distance to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are anywhere near the appliance.

• Clothing or other flammable material should not be hung from the appliance, or placed on or near the appliance.

• Any screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

• Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required as necessary. It is imperative that the control compartments, burners and circulating air passageways of the appliance be kept clean.

• Do NOT burn solid fuels in this gas fireplace.

• Do NOT ignite the burner before pouring all of the burner media (fire glass) into the burner pan. The media must be evenly distributed over the burner.

• During initial firing of firepit, please stay away from the firepit for 20 minutes as fire media (fire ice) may pop and hit someone on the face or eyes.

• Do NOT ignite or use the firepit if the burner media (fire glass) are wet. Ensure the burner media are completely dry before igniting as intense heat could cause the media to crack and pop.

• It is UNSAFE to use this product for cooking!
  CAUTION: The propane gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 37 mbar.

• This outdoor gas appliance is not intended to be installed in or on recreational vehicles and/or boats.

• Before each use of this gas appliance, open the LP (Liquid Propane) Tank Drawer and inspect the LP Hose. If there is evidence of excessive abrasion or wear, or the hose is cut, it must be replaced prior to the gas appliance being put into operation. Use only the replacement hose assembly specified in this manual. Inspect the burner before each use of the appliance. The burner must be replaced prior to the appliance being put into operation if it is evident that the burner is damaged. Use only the burner listed in these instructions.

• Keep the fuel supply hose away from any heated surfaces. Check the tubing or the flexible hose (at least once per month and each time the cylinder is changed). If it shows signs of cracking, splitting or other deterioration it shall be exchanged for new hose of the same length and of the equivalent quality; The tubing or the flexible hose must be changed within the prescribed intervals

• Shut off the valve at the gas cylinder or the regulator before moving the appliance Be careful, accessible parts may be very hot. Keep away from young children

• Do Not move the appliance during use.

IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS

• The cylinder supply system must be arranged for vapor withdrawal.

• This appliance shall be used only outdoors in a well-ventilated space and shall not be used in a building, garage, or any other enclosed space.

• When this appliance is not in use, the gas must be turned off at the supply cylinder.

• Storage of this appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance.

• Cylinders must be stored outdoors in a well-ventilated area out of the reach of children .Disconnected cylinders must have protective caps installed and must not be stored in a building, garage, or any other enclosed areas.

• Change the gas cylinder in an amply ventilated area, away from any ignition source
  (candle, cigarettes, other flame producing appliances).

• Check that the regulator seal is correctly fitted and able to fulfill its function.

• Do not obstruct the ventilation holes of the cylinder housing.

• Use only the type of gas and the type of cylinder specified by the manufacturer.

• In case of violent wind particular attention must be taken against tilting of the appliance.

This appliance is for use only with a 5KG Patio Gas Cylinder unless converted for use with Natural Gas with the provided gas conversion kit. The cylinder must be equipped for a clip-on regulator. See Figure 1.

SPECIFICATIONS

Clearances to combustible

surfaces

| Sides    24 in / 60.96 cm| Top: 72 in / 182.88 cm

PARTS IDENTIFICATION LIST

INSTALLATION

1. Carefully unpack all items from the box. Place the base in the final position. There must be a minimum of 60.96 cm / 24 inches of clearance from the side of the table top to any combustible walls.
2. Attach a leg connector bracket to a table leg by using two 1/4″x20 mm bolts and Ø6.5×1.0 mm washers as shown in Figure 2. Guide the bolts through the holes in the leg connector bracket, into the pre-drilled holes in the table leg. Hand tighten only 2-3 turns. Repeat for the other leg and leg connector bracket.
3. Place the tabletop onto the assembled firepit base. Secure the tabletop to the firepit base by using four 1/4″x20mm bolts and Ø20xØ6.5×2.0mm washers as shown in Figure 3. Hand tighten only.
4. Attach a complete leg to the firepit table top by using two 1/4″x35 mm bolts and Ø20xØ6.5×2.0mm washers as shown in Figure 4a. Repeat for the other complete leg. Attach a complete leg to the firepit base by using two 1/4″x30 mm bolts and Ø6.5×1.0mm washers as shown in Figure 4b. Repeat for the other complete leg.
5. After making any necessary adjustments to the alignment of the firepit, use the hex bolt driver to tighten all bolts. Repeat until all bolts are tight. Do not over tighten. Over tightening may strip bolts. With the help of another person, turn the table in the upright position.
6. Place the burner pan protective ring into the firepan/burner assembly as shown in Figure 5. Align the holes in the burner pan protective ring with the pre-drilled holes on the firepan/burner assembly. Secure the burner pan protective ring to the firepan/burner assembly by using the M4 screws as shown in Figure 5.
7. Pour ALL of the provided media (fire ice) into the burner pan. Burner MUST be completely covered to ensure the appliance functions properly and safely. Remove any fire ice on top of the ignition well. See Figure 6.
8. Slide the tank drawer out, place the LP tank (not provided) in the drawer and secure it with the chain as shown in Figure 7. With the BLACK lever in the “down/off” position as shown in Figure 8, firmly push the regulator onto the tank valve. To open the valve, lift the BLACK lever and turn the handle 90° clockwise to the “ON” position. See Figure 9. Apply a solution of soapy water to the tank-regulator connection and to the valve-hose connection to check for leaks. If soap bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve and tighten all connections. NEVER USE A FLAME TO CHECK FOR LEAKS. In case of gas leakage; for instance, in the event of gas leakage, the appliance shall not be used or if alight, the gas supply shall be shut off and the appliance shall be investigated and rectified before it is used again. To remove the regulator, turn the Black Lever counterclockwise and press straight in. See Figure 10.

Natural Gas Conversion

Natural gas conversion must be performed only by your natural gas provider or service company.

1. SHUT OFF THE GAS SUPPLY TO THE UNIT AND ANY NEARBY ELECTRICAL SOURCE OR APPLICANCES

2. Below the burner, carefully disconnect flex connector attached to the orifice holder (see step1).

3. Carefully unscrew the orifice holder from the burner pipe (see step2).

4. Remove the propane orifice from the holder and replace with the natural gas orifice (see step2).

5. Install the air shutter over the burner pipe to cover the air holes. Then reattach the orifice holder to the burner pipe (see step3). Special attention should be payed to the leakage between the holder and natural gas orifice. Do the leakage test with the valve opening.

6. Reattach the flex connector to the orifice holder. (see step 4).

7. To convert the regulator from propane to natural gas, the appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve. Ensure any pressure testing of the gas supply piping system is at test pressure equal to or less than 1/2 psi(3.5KPA)

8. Remove the propane rubber hose from valve and replace with 5/8” natural gas pipe (see step5, natural gas pipe package is not provided).

9. Restore your gas supply and check ALL of the connections for leaks using a solution of soapy water. If a leak is discovered and any bubbles are seen, close the main gas valve and re-tighten
   ALL the connections. NEVER USE A FLAME TO CHECK FOR GAS LEAKS!

10. Stick the conversion label on the rating plate as shown in Figure 11.

BATTERIES

Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignition module located on the control panel to access the battery compartment. The ignition module requires one Alkaline AA size battery. The negative (-) end goes in first. See Figure 12. Dispose of the battery safely as it may explode or leak if charged or disposed of in a fire. Make sure of the polarity. Mercury and cadmium free.
CAUTIONS: BATTERY INSTRUCTIONS

• Always purchase the correct size and grade of battery most suitable for the intended use.
• Always replace the whole set of batteries at one time, taking care not to mix old and new ones, or batteries of different types.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries are installed correctly with regard to polarity (+ and -).
• Remove batteries from equipment which is not to be used for an extended period of time.
• Remove used batteries promptly.
  For recycling and disposal of batteries to protect the environment, please check the internet or your local phone directory for local recycling centers and / or follow local government regulations.

MAINTENANCE

The flames should look like those in Figure 13. To clean the burner, use a soft brush after the burner has cooled completely. Never use a vacuum cleaner on the burner. It is recommended to store the fire pit indoors during winter if it will be subjected to freezing temperatures. The LP cylinder must be disconnected and removed from the appliance before the appliance can be stored indoors.

LIGHTING INSTRUCTIONS

Warning: If these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

1. Read instructions before lighting.
2. Push and turn the knob to ON.
3. Hold ignitor to light the burner, release control knob after 15 seconds; if burner does not light , wait 5 minutes ,repeat.
4. Adjust flame to desired flame with the control knob. See Figure 14.

BURNER COVER ASSEMBLY

Place the burner cover on the table top as shown in Figure15.
WARNING: BEFORE PLACING THE BURNER COVER ON, MAKE SURE THE FIREPIT HAS BEEN SHUT OFF AND THE BURNER HAS COMPLETELY COOLED DOWN.

TROUBLESHOOTING GUIDE

Burner Won’t Light

| ****

No propane gas at burner

| Check that the gas tank valve is open. Turn the control knob to “ON” and push the control knob in. Make sure the tank

has propane gas.

No spark at electrode

| Check that the AA battery is installed with the negative (-) end first and has a charge. Check that the wire is connected to the ignition module.

Check that the electrode is not cracked or broken.

Lack of oxygen| Remove excess fire ice from around

the ignition well.

Burner won’t stay lit after lighting

| ****

Thermocouple not in Flame

| Check that the tip of the thermocouple is even with the top of the ignition well. Remove any fire ice from the ignition well.

Thermocouple connection at the main control valve is loose.

| ****

Tighten the thermocouple nut at the back of the valve.

No fire ice on burner| Cover the burner with fire ice per the instructions.

1. For use outdoors or in amply ventilated areas.
2. An amply ventilated area must have a minimum of 25% of the surface area open.
3. The surface area is the sum of the walls surface.

The hose should comply with the standard EN16436;
The regulator should comply with the standard EN16129;
Close the gas supply at the valve of the gas cylinder or the regulator after use; Do not connect the gas cylinder directly to the appliance without the regulator; The recommended cylinder size is-max diameter: 310mm, max height: 400mm.

Manufacturer: Agio International Corporation
900 E Hamilton Ave, Suite 100, Campbell, CA 95008, USA

Importer : Costco Wholesale UK Ltd / Costco Online UK Ltd
Hartspring Lane Watford, Hert WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk

CARE AND MAINTENANCE

FRAMES

Cleaning – Use mild soap and warm water. Do not use abrasive materials, cleansers or bleach products. Rinse with clean water and dry thoroughly.
Maintenance – Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to remove all water. This is critical. Water allowed to accumulate inside the frames and then exposed to sub-freezing temperatures can cause damage to the frame tubing. Such damage is not covered under warranty. Always clean, drain and dry thoroughly before storing for the winter. For best results, always store or cover your furniture when not in use.
** When cleaning or moving large or heavy items, always have two people work together. Never drag furniture.

SPECIAL WARNINGS
THIS ITEM IS INTENDED FOR OUTDOOR DOMESTIC USE ONLY, NOT FOR COMMERCIAL USE.
Furniture covers are a great way to protect your set from harsh elements of weather and UV light. However, it is important to ensure furniture and covers are free of moisture and debris before covering. It is also necessary to promptly uncover furniture after rain and during periods of high humidity to prevent moisture build up. Failure to do so can lead to permanent surface and finish damage.

IMPORTANT INFORMATION ABOUT CLAY AND PORCELAIN TILE

About Clay / Porcelain Tile
Clay / Porcelain Tile is a material that is compressed and heated at high temperatures. Though the material is stain resistant, the grout is porous and could stain. Your tabletop has been sealed and protected with a specially formulated, high-quality sealer to minimize staining.
The tabletop can retain heat depending on the outside temperature. In sunny hot weather conditions, care should be exercised when touching the tabletop.

Care and Maintenance
Your tabletop is protected with our specially formulated factory sealer that offers a high level of protection from all stains and acidic liquids and should not break down over time or with normal outdoor use.
The tabletop should not require frequent reapplication of sealer to maintain its durability and the sealer can be easily repaired if it becomes scratched or damaged. However, should you choose to seal your tabletop, you should use only the sealer that was applied to your tabletop during its factory production.
Chemical formulations of sealer products vary and could be incompatible with the sealer that was originally used on your tabletop. Using any sealer other than our factory sealer might produce undesirable results and will void any applicable warranty. Before you reseal your tabletop or to obtain our factory sealer, please visit our website at www.agio-usa.com/claycare or www.agio- usa.com/porcelaincare or call our Customer Service Center in the US and Canada at 1-888-383-1932.

Cleaning
Clay and porcelain are virtually maintenance-free. Just keep the table clean with mild soap and water to keep mold & mildew from forming. Simply use clean water and mild dish soap. Clean the tabletop with a soft, clean, white cloth or sponge.
Never use scouring creams, abrasive cleaners, acids, or petroleum-based products. Rinse with plenty of clean water to remove soap residue. Dry thoroughly after cleaning to prevent buildup of any residue from minerals that might be present in your water, even with softened water.

Spills
Accidental spills should be cleaned immediately even though your tabletop is sealed. Wipe spills with a clean, soft white cloth. Rinse with clean, warm water and dry thoroughly. The special factory sealer forms a protective barrier that will minimize potential damage to the tabletop by allowing more clean-up time for accidental spills.

Recommendations
To help protect the sealer, use coasters and placemats when dining. Coasters will help absorb sweating by beverage containers and prevent hot containers such as mugs from leaving rings. Placemats will catch spills and prevent dishes from scratching the sealer if dragged across the tabletop. Use trivets or hot pads between dishes and the tabletop to minimize rapid heat transfer. The tabletop can rapidly draw heat from a hot dish and potentially crack the dish. Cover your dining set with an outdoor furniture cover when not in use.
For additional and more detailed information on clay/porcelain tabletop care, sealing the tabletop or repairing damages, visit our website at www.agio- usa.com/claycare or
www.agio-usa.com/porcelaincare or call our Customer Service Center in the US and Canada at 1-888-383-1932.

Do not attempt to assemble the chair if any parts are missing or damaged.

CAUTION: Failure to place metal plates (G) and above the “U” bar exactly as shown in the diagram will cause the bolt heads and nuts to damage the structure of the “U” bar. Damage due to over tightening of bolts or improper assembly could cause injury and may void your warranty.

Installation

Costco Wholesale UK Ltd /Costco Online UK Ltd Hartspring Lane
Watford, Herts
WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk

References

• USA Location information - USA.com
• USA Location information - USA.com
• agio-usa.com/service-center/costco
• Costco International - Agio International
• Maintenance - Agio International
• Inicio | Costco México

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>