Pro-Ject VT-E BT Wireless Plug and Play Turntable User Manual

Pro-Ject VT-E BT Wireless Plug and Play Turntable

OVERVIEW

Mounting kit for wall mount

Controls, features and connections

1. Power switch
2. Motor with motor pulley
3. Platter
4. Drive belt
5. Chassis
6. Screwable record clamp
7. Tonearm counterweight
8. Tonearm lift
9. Tonearm rest and removable transport lock
10. Tonearm tube
11. Headshell with finger lift
12. Ortofon OM 5E cartridge
13. Feet
14. Line Output
15. Phono Output
16. Grounding screw
17. BT switch
18. Rear support
19. Power supply socket Universal power supply (not shown) Single adapter (not shown) Allen key (not shown) *

Mounting kit for wall mount

1. The main wall holder
2. Bottom support 2x
3. M6 nut 2x
4. M6 washer 2x
5. M6 x 35 screw for rear support or main wall holder
6. Pro-Ject DAMP IT

Packaging overview

Dear music lover,

• Thank you for purchasing a Pro-Ject Audio Systems record player.
• In order to achieve maximum performance and reliability, please study these instructions carefully.
• Warning of a hazard for the user, the unit or possible misuse
• Important notice
• During assembling and adjustment small parts could be lost if they are not carefully placed in a suitable receptacle. Before starting assembly make yourself acquainted with the parts listed above which are correspondingly numbered in the technical drawings above. Separately packed items are marked with an asterisk *.

Safety instructions

• The power supply is used to connect and disconnect the unit from the mains. Make sure that the plug is easily accessible at all times. Hold the plug when unplugging the power cord. Never handle the power cord while your hands are wet or damp.
• Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase, on or near the device. Never spill any liquid on the device. Never place any naked flame sources, like lighted candles, on or near the device. The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
• Keep plastic bags away from children to prevent any risk of suffocation.
• The turntable was shipped partially disassembled in order to avoid damage to sensitive parts. Please check immediately to make sure that neither the packaging nor the device was damaged in transit.

SETUP AND INSTALLATION

PART 1 – DESKTOP USE
ASSEMBLING THE REAR SUPPORT
Remove the rear support panel (18) from the packaging and prepare two M6x35 screws for mounting. Using the screwdriver, carefully tighten the screws to fix the rear support panel on the turntable’s chassis (5) as shown in the following illustration. MOUNTING THE PLATTER, DRIVE BELT AND RECORD CLAMP
With the rear support (18) mounted and the turntable in vertical position, install the platter (3) and the drive belt (4) as shown in following illustration.

After placing the record on the platter, it is necessary to tighten the screw- able record clamp (6) onto the platter spindle.

PART 2 – WALL MOUNT
DISASSEMBLING THE REAR SUPPORT
Remove two M6 screws which hold the rear support (18) in the back of the turntable.

ASSEMBLING THE MAIN WALL HOLDER
For wall mount, it is necessary to mount the main wall holder (1 – mounting kit) instead of the rear support (18). For correct mounting, follow instructions from next illustration.

ASSEMBLING THE BOTTOM SUPPORT

With the main wall holder mounted on the turntable, unscrew both feet (13) from the bottom and instead of the feet screw the bottom support (2 – mounting kit) as shown in the following illustration.
Now the VT-E is ready for mounting on the wall.

MOUNTING ON THE WALL
Mount the turntable on the wall through supplied damping pad Pro-Ject Damp IT.

We recommend using the appropriate type of mounting screw for given type of the wall.

MOUNTING THE PLATTER, DRIVE BELT AND RECORD CLAMP
With the turntable mounted on the wall, install the platter (3) and the drive belt (4) as shown in following illustration.

After the placing the record on the platter, it is necessary to tighten the screw-able record clamp (6) onto the platter spindle.
CARTRIDGE, VERTICAL TRACKING FORCE (VTF)
The turntable is supplied with fitted cartridge Ortofon OM 5E. The counterweight (7) supplied is suitable only for Ortofon OM cartridges. Cartridge downforce is pre-adjusted from the factory.

• Please note: It is not recommended to change the cartridge or vertical tracking force without prior consultation with your dealer.

CONNECTION TO THE AMPLIFIER

• The record player has two possible outputs – Line OUT (14) with integrated preamplifier and Phono OUT (15) for connection to the preamplifier. If you choose Phono OUT (15), than use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used. If you choose Line OUT (14), than use the Line inputs (like CD, Tuner, Tape or Video).
• Take care about connecting the left and right channel correctly. The RIGHT CHANNEL is usually marked RED, the LEFT CHANNEL BLACK or WHITE. Check the manual of your amplifier for relevant information. An earthing wire may be connected to the screw terminal between the sockets if you encounter humming problems.
• For detailed product information regarding Pro-Ject Audio Systems interconnect cables, phono amplifiers and stereo power amplifiers, please visit our website:
• www.project-audio.com

BT PAIRING

The record player has BT output and transmits the signal automatically when is turned ON by using BT switch (17). It is paired automatically with any device with BT receiver (such as Pro-Ject MaiA, MaiA DS, BT Box s and BT Box E).
For pairing with other devices and portable speakers use the manual of the given product.
For restart of the BT transmitter, please turn OFF and ON the BT module by using the switch. Restart is needed only when there is a change of the BT receiver.
For detailed product information regarding Pro-Ject Audio Systems BT audio receivers, please visit our website: www.project-audio.com
MAINS POWER CONNECTION
The turntable is supplied with a power supply suitable for your country’s mains supply. Check the label before connecting to ensure compliance with the mains rating in your house.

• Connect the low voltage plug from the power supply to the socket (19) on the rear of the record player before connecting the power supply to the mains.

SWITCHING ON AND OFF

• Pressing the power switch (1) alternately starts or stops the motor.

CHANGING REPLAY SPEED

• To play records at 45 r.p.m., put the drive belt (4) over the larger diameter part of the motor pulley (2). To revert to 33 r.p.m. repeat the proceedings using the smaller step on the pulley.

MAINTENANCE AND CLEANING

• Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attracts even more dust! Antistatic cleaning fluids are available at specialized stores but must be applied sparingly to avoid damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance to avoid damage.
• If the player is not used over a long period of time, the drive belt should be removed to prevent unequal stretching.
• Always disconnect the record player from the mains power supply as a precaution before maintenance!

Technical specifications

Pro-Ject VT-E R / Pro-Ject 8,6’’ EV tonearm

• Nominal speeds 33/45 r.p.m.
• Speed variance 33: ±0,80 % 45: ±0,70 %
• Wow and flutter 33: ±0,29 % 45: ±0,27 %
• Signal to noise 65Db
• Effective tonearm mass 8g
• Effective tonearm length 8,6 ” (218,5mm)
• Overhang 22mm
• Power consumption 4,5W (5W max)/ < 0,3W standby mode
• Outboard power supply 15V/ 0,8 A DC, universal power supply
• Dimensions (W x H x D) 430 x 345 x 245mm
• Weight 2,8 kg

Technical specifications MM-Cartridge Ortofon OM 5E

• Frequency range 20-25.000Hz
• Channel separation 22dB/1kHz
• Output voltage 4mV
• Recommended load impedance 47kohms/amplifier connection – MM-input
• Compliance/stylus type 20μm/mN – elliptical
• Recommended tracking force 17,5mN
• Weight 5g

FCC ID

Federal Communication Commission (FCC) Interference Statement FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC´s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
  Contains FCC ID: 2ARV2-EP3056T

Potential incorrect use and fault conditions

• Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included.

The platter doesn’t turn although the unit is switched on:

• The unit is not connected to the mains power supply.
• No mains at the socket.
• Drive belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

• No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
• Phono input not selected at amplifier.
• Amplifier not switched on.
• Amplifier or speakers defective or muted.
• No connection to the loudspeakers.
• Strong hum on phono input:
• No earth connection from cartridge / or arm / or arm cable to amplifier, or earth loop.
• Distorted or inconsistent sound from one or both channels:
• Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set. Needle or cantilever damaged.
• Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

Service

• Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
  Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
  Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.

Warranty

• The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.
• Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
• This guide was produced by: Pro-Ject Audio Systems Copyright © 2022. All rights reserved.
• The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
• © Pro-Ject Audio Systems · Pro-Ject VT-E BT R · Revision 22.06.2022 13

Documents / Resources

| Pro- Ject VT-E BT Wireless Plug and Play Turntable [pdf] User Manual
VT-E BT Wireless Plug and Play Turntable, VT-E BT, Wireless Plug and Play Turntable, Plug and Play Turntable, Play Turntable
---|---

References

• Pro-Ject Audio Systems – Turntables and hifi stereo components since 1991 | Handmade in Europe

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>