NOYAFA NF-168V Anti-Interference Wire Tracker User Manual

: June 4, 2024
: NOYAFA

Table of Contents

Brief introduction
Product Interface and Keypad Introduction
Operation methods
Other functions
Specification
Packing list
Diagram of series products
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Your excellent helper in measuring instruments.
ANTI-INTERFERENCE WIRE TRACKER
USER MANUAL

Find target wire required from numerous telephone wires and LAN cables

ExampleⅠ

Trace cable in telephone exchanger

Connect launcher and telephone wire port to be traced in right way| Trace cable at the other end with receiver

ExampleⅡ

Trace cable in the distribution frame

Connect launcher and LAN cable port to be traced in right way| Trace cable at the other end with receiver

**** Please read and learn safety instructions before using or maintaining the equipment

Never expose the equipment directly to the sun.
Never put the equipment in a place with much dust, humidity, and high temperature (over 40℃)
Please use the battery according to the specification; otherwise, it may result in damage to equipment.
Please never dismount the equipment arbitrarily. The maintenance and care shall be conducted by professional personnel.
Please take out the battery in the launcher and receiver if the equipment is not used for a long time so as to prevent the battery liquid is leaked in the future.
Never use the equipment to detect a power cord with electricity (such as a power supply circuit of 220V), otherwise, it may result in damage to equipment and personal injury.
Never conduct related operations of the communication line in thunderstorm weather so as to prevent lightning stroke and impact on personal safety.

Brief introduction

NF-168V/NF-168S is an updated item with multifunction of cable tracing, mapping, and Visual fault locator (this function is only for NF-168V) according to sales requirements. It follows the shells of NF-168 emitter and receiver. But compared to series products, its highlights is three tracing modes, three mapping mods, and a Visual fault locator. Tracing modes–Anti- interference, PoE switch; Cable mapping–Fast mode Slow mode Ordinary tracing, fault locator-Continuous mode, Pulse mode. Manual mode; Visual

Product Interface and Keypad Introduction

Operation methods

Cable tracing
1)Basic tracing Emitter Push the key to SCAN” to enter the basic tracing mode, then blue indication flashes “ , which means the emitter works well. Connect one end of network cable/telephone cable(BNC cable only for NF-168S) to the RJ45/RJ11 (BNC cable only for NF-168S) port of the launcher. Receiver Push the key to “Basic” the brightness of the indicator and the sound of the speaker is, dynamically changed according to the signal strength. (note that in this mode, even if there is no signal, the indicator and the speaker will have a weak change) which, means the receiver works well and then holds the receiver to find the target line. ,

2) AC filter tracing Emitter:
In the basic mode, short press the “SET” button to enter the AC filter mode, then the blue indicator flashes, which means the emitter works well. Connect one end of network cable/telephone cable (BNC cable only for NF-168S) to the RJ45/RJ11(BNC cable only for NF-168S)port of the launcher. Receiver: Push the key to “AC Filter”, the brightness of the indicator and the sound of the speaker is dynamically changed according to the signal strength, which means the receiver works well, then hold the receiver to find the target line.

3)PoE switch Emitter:
In AC filter mode, short press the “SET” key to enter POE scan mode, then the indicator flashes red and blue, which means the emitter works well. Connect one end of the network cable to the RJ45 port of the launcher. Receiver: Push the key to “AC Filter” to enter PoE switch mode, the brightness of the indicator and the sound of the speaker is dynamically changed according to the signal strength, which means the receiver works well, then hold the receiver to find the target line.

NOTICE
When the battery of the emitter is low, the red light below will flash , otherwise, it will not light. When the battery of the receiver is low, the red light above flashes, otherwise it is always on; the user can adjust the sensitivity on the right to achieve the best scanning effect according to the usage scenario.

2. Tracing mapping ( RJ45 as an example)

Connect two ends of the network cable to the RJ45 port of the launcher and receiver separately.
And push the key to “test”, the wire sort indicators will flash, which means the transmitter works well.
If the wire is normal, and the GND is not connected, then the 8 indicators will flash one by one. And if GND is connected, then the 1 to 8 and G indicators will flash one
by one.
If there is miswires as below. If the line“2” is open, then the 2 indicators of emitter and receiver will not flash. If there is several lines are open, the corresponding indicators
will not flash. And if less than 2 lines are connected, none of the lights is on. When the line is cross, for example, line“2” and line“3” disorder, the indicators
flash as follows,
Transmitter : 1-2-3-4-5-6-7-8-G
Receiver: 1-3-2-4-5-6-7-8-G
When there is a short circuit of lines “2” and “3”, the 2 and 3 indicators of the receiver will not flash while the other lights still do.
The wire tracker has three mapping modes as below:

1) Fast mode(0.5 second)
Emitter: Push the key to “test” to enter Fast mode, the wire sort indicator flashes, then the LED indicator will flash by one bye one per 0.5 second.

2) Slow mode(1 second) second
Emitter: In the fast mode, short press the “SET” button to enter the slow mode, the wire sort indicator flashes, then the LED indicator will flash by one bye one per 1.

3) Manual mode
Emitter: In fast/slow mode, long press “SET” button to enter manual mode, a user needs to short press “SET” button, the wire sort indicator flashes, then the LED indicator will flash stage by stage.

NOTICE
When the battery of the emitter is low, the red light above will flash, otherwise, it will not light. When mapping, Only connect the cable to be tested to the Rj45 port of emitter and receiver, at this time the LED light status will show the cable continuity.

3. Visual fault loactor (this function is only for NF-168V)
This function can inspect fiber failure when they connect with the optical interface. It’s light has two modes as below.
1)Continuous mode
In any cable tracing mode, long press the “SET” button enter the continuous mode, this mode defaults. You will see the red laser emitting from the optical interface. At this time, the upper red light also will flash. (Please don’t stare at the beam, for fear of damaging your eyes).

2)Pulse mode
In the continuous mode, short press the “SET” button to enter the pulse mode, and the LED synchronizes with light-emitting (pulse frequency will be controlled at 1-2 Hz). At this time the upper red light also will flash.

NOTICE
When they battery of emitter is low, the indicator below will flash, otherwise, it will not light.

Other functions

Low-voltage hint function
When the battery is low (≤6V), push the function button to “scan” or “test” , at this time, both the scan indicator and wire sorting indicator will flash, which means the battery should be replaced.
Earphone function
The earphone can be worn in a noisy environment for operation so as to avoid external interference.
Sensitivity adjustment function
Turn the sensitivity adjustment knob on the receiver when tracing the cable to adjust the value to be the appropriate degree.
Floodlight function
The side floodlight can be started at night or in dark. The floodlight turns on so as to facilitate your normal operation.
Wire sorting directly with switch
Connect the line to be tested with the transmitter and switch, then get the result from flashlights.

Specification

Emitter	Tracing	Compatible cable	R.145, R.111, BNC cable
Max. signal voltage	8±1.0Vp-p
Max volume	105dB
Tone frequency	455Hz
Tone mode	1 Tone
Ordinary tracing	YES
Anti-interference	YES
Distance of transmission	R145 300M non-load/load

Packing list

Emitter	I PC	User manual	I P(
Receiver	I PC	Battery	2PCS
Testing line	I PC	Kit	I PC

Earphone
.| I PC| Color box| I PC

Diagram of series products

Your excellent helper in measuring instruments.

VER: V1

Documents / Resources

| NOYAFA NF-168V Anti-Interference Wire Tracker [pdf] User Manual
NF-168V, NF-168S, Anti-Interference Wire Tracker, Interference Wire Tracker, Wire Tracker, NF-168V, Tracker
---|---