AIVO ANCP3005Q Professional Wi-Fi CPE Network Bridge User Guide
- June 14, 2024
- AIVO
Table of Contents
Professional Wi-Fi CPE Network Bridge
Quick Start Guide Wi-Fi CPE Network Bridge
Model ANCP3005Q
Device Setting
1.1 AIVO Network’s ANCP30050 is a professional Wi-Fi communication device,
which enables connection from existing LAN to remote location using the latest
wireless technology. We strongly recommend professional installation.
1.2 Installation Diagrams
Quick Setup
2.1 Connect the computer using an Ethernet cable to LAN port of the CPE
device. Make sure computer is set to the same IP range as the CPE device.
{i.e. 192.168.10.x) Open the internet browser and type default IP address
192.168.10.1 to access management interfece.Default password should be “admin”
2.2 AIVO ANCP30050 can
operate as bridge, AP, Repeater and Router mode. In order to use AIVO
ANCP30050 as wireless bridge for IP cameras or to connect networks together,
we recommend to use two ANCP300SQ devices for the maximum transfer distance
and speed.
AP Mode
3.1 AIVO ANCP30050 can be used as a outdoor AP. For AP mode, select Wizard >
AP Mode in the menu on the left side. Type the IP address to preference. IP
address must be within the same network as Router/Gateway’s LAN IP range and
must not conflict with any other devices. Click Next after done.
3.2 Type the desired SSID
name and password to for wireless network. (For some dual band device, it may
requires 2 SSID names. We recommend to use different names for those 2
networks. ie. AMO_2.4G and AIVO_SG)
Bridge Mode
4.1 For bridge mode, Wizard > AP Mode in the menu on the left side. Choose
Access Point for transmitting mode or Station for receiving mode. For the
maximum performance, WDS feature on the router must be enabled.
4.2 For Access Point mode,
select Access Point option and type in preferred IP address for the CPE unit.
4.3 Type the desired SSID
name and password, then adjust transmitting distance to your preferred range.
Please note, longer distance in range will narrow down the beam pattern thus
less side to side coverage.
4.4 For setting up CPE as
receiver, select Station mode at the first menu. Under station mode there are
two options. Client Site and Secondary Site. For most IP camera settings, use
Client Site mode. For bridging two networks together, use Secondary Site mode.
Repeater Mode
5.1 AIVO ANCP3005Q can operate as WiFi repeater/extender. For repeater mode,
choose Wizard > Repeater Mode in the menu on the left side. Type in preferred
IP address for the CPE unit. Make sure IP address for the CPE is in the same
network IP range with the router/gateway.
5.2 Click Sean to find all
the available WiFi networks. Select the desired wireless network from the
list, then click 4 . Type password for the selected wireless network and click
next to continue.
5.3 Type the desired SSID
name and password to for repeater/ extender’s wireless network.
Router Mode
6.1 For Router mode, Wizard > Router Mode in the menu on the left side. Choose
the proper setting for your Internet Service Provider. (PPPOE, Static, or
DHCP)
6.2 Type the desired SSID
name and password to for wireless network. (For some dual band device, it may
requires 2 SSID names.
We recommend to use different names for those 2 networks. i.e, AIVO_2.4G and
AIVO_5G)
Copyright Information
Statement
Big Cart Corporation Company all rights reserved.
Without our official written permission, no unit or individual shall be
copied, reproduced, transcribed or translated in part or whole book.
In any form or by any means (electronic, mechanical, printing, recording or
other possible means) or for the propagation of goods any commercial,
profitable purposes.
AIVO” is the registed trademark of Big Cart Corporation Company in California,
United States. All other trademarks or registed trademarks mentioned in this
document, by respective owners.
Product specifications and information mentioned in this manual are for
reference on subject to updates without notice. Unless there are other special
agreed, this manual is used only as a user guide. All statements, information,
etc. are not consitute any form of guarantee.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interferenceto radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>