FLYSKY FS-iBA01 Altitude Sensor User Manual

: June 9, 2024
: Flysky

Table of Contents

Introduction
Overview
Specifications
- Diagram:
Certification
- FCC Compliance Statement
Customer Support
Documents / Resources

FLYSKY FS-iBA01 Altitude Sensor

FS-iBA01 Altitude Sensor

Introduction

FS-iBA01 is a altitude sensor that adapts to Flysky AFHDS 3 enhanced receiver in compliance with i-BUS2 protocol. It features compact design, easy installation, real time altitude data return, and adaption to a variety of car and airplane models.

Overview

Signal pin
+ (Power anode)
– (Power cathode)
LED

Specifications

Product Type: FS-iBA01
Compatible Devices: Supports receivers that comply with i-BUS2 protocol series (such as FTr8B, FTr12B, INr6-HS and other Flysky AFHDS 3 enhanced receivers).
Compatible Models: Cars or airplanes, etc.
Protocol: i-BUS2
Measurement Accuracy: 1m
Measurement Range : -1000 ~ 8000m
Vario meter: -150m/s ~ +150m/s
Input Power: 3.5 ～ 9V/DC
Working Current: 10mA/5 V
Online Update: No
Dimensions: 160mm（Length ）
Weight: 3.5g
Temperature Range: -20℃ ~ + 85℃
Humidity Range: 20% ~ 95%
Certifications: CE, FCC

Do not put the sensor in a sealed location.
Do not install in a location where the wind/air flow can hit the sensor.
The sensor calculates the altitude from atmospheric pressure. Atmospheric pressure will get lower as you go up in altitude. Using this the sensor will estimate the altitude. In addition, atmospheric pressure may changes due to weather conditions, such as temperature, humidity and other factors, the altitude display may vary slightly at the same position.

Follow the steps below for installing the altitude sensor.

Use 3M stickers to fix the temperature sensor at the appropriate location of the model. It should be noted that the fixed surface should be flat. You can also use a cable tie to tie it to the model. In this case, you should control the force.
Connect the servo interface to the Newport interface of the receiver. Set the protocol of the corresponding Newport interface of the receiver to i-BUS2 at the transmitter side which is bound to this receiver. As a result, you can view the relevant information at the transmitter side.

Diagram:

Installation

Notes:

The cable length may vary to different applications. If you need to add an extension cable, please note that the FS-iBT01 interface is a servo interface, and for the pin definition, refer to the description in the previous Overview section.
The compatible transmitters which support i-BUS2 protocol: Noble (firmware
version V2.0.93 or later), Noble Lite (firmware version V1.0.10 or later), Noble pro, PL18 (firmware version 1.0.55 or later) and PL18 Lite (firmware version 1.0.65 or later).
If the altitude sensor is working properly, the LED is solid on at this time.
If the sensor is connected to power supply but no i-BUS2 signal is detected, the LED flashes slowly at this time.

Attentions:

Ensure that the sensor is connected properly to the receiver, failure to do so may result in damage to the sensor.
Ensure that the sensor is connected properly to i-BUS2 interface of the receiver before use.
To ensure that the sensor is functioning as desired, please test accordingly

Certification

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

EU DoC Declaration

Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FS iBA01] is in compliance with RED 2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.flysky-cn.com.

RF Exposure Compliance

The distance between user and products should be no less than 20cm.

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

| Bili Bili| Website|

Facebook

---|---|---|---

Customer Support

Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Product design and specifications may be changed without notice.
Manufacturer: ShenZhen FLYSKY Technology Co., Ltd Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China
http://www.flysky-cn.com
Copyright ©2022 Flysky Technology co., ltd