MOULTRIE MFG-15050 Ranch Series Gravity Feeder Kit Instructions

**MOULTRIE MFG-15050 Ranch Series Gravity Feeder Kit Instructions

**

TOOLS

• Bolt  M6 x 1 x 18 Qty.

• Hex Nut M6 x 1 Qty. 9

• Flat Washer M6 Qty. 6

ASSEMBLE FEEDER KIT

1. Remove all hardware from packaging.
   

2. From the inside of your feeder hopper, install (3) M6 bolts, fitted with washers, through the mounting bolt holes on the bottom. Do not thread anything onto the bolts at this time, this will be the mounting hardware for the gravity kit.
   

3. Fit the Extension Tube to the top of the gravity head, aligning the 3 bolt holes.
   

4. From the outside of the extension tube, Insert the (3) M6 bolts through the holes from Step 3. Secure with the supplied hex nuts on the inside of the tube. Once all three bolts are in place and hex nuts are finger tight, fully tighten with 10mm wrench.
   ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench)
   

5. Following the same procedure from Step 4, attach the Mounting Plate (ribs facing downward) to the top of the Extension Tube.
   ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench)
   

6. The kit is now ready to be installed to your hopper. Align the pre-installed mounting studs from Step 2 with the (3) holes in the mounting plate, then secure the kit using (3) Flat Washers and (3) Hex Nuts.
   ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench)
   
   

TOOLS

• Short M6 Bolt M6 x 1 x 14 Qty. 20

• M6 Lock Nut M6 x 1 Qty. 20

• Short M8 Bolt M8 x 1.25 x 14 Qty. 8

• M8 Lock Nut M8 x 1.25 Qty. 16

• Long M8 Bolt M8 x 1.25 x 60 Qty. 8

ASSEMBLE THE HOPPER

1. Remove all hardware from packaging.
   

2. Gather all 4 hopper panels and the hopper cone.
   

Place the cone on its side, with the front arrow pointing upwards. Attach both side panels to the cone using (6) Short M6 Bolts and (6) M6 Lock Nuts. Hand tighten only.

Place a face panel on top of the cone and overlapping the side panels. Align the bolt holes in the cone with the (3) lower holes in the face panel. Secure using (3) Short M6 Bolts and (3) M6 Lock Nuts. Hand tighten only.

Flip the hopper over and install the remaining face panel following the same procedure above.

OPTIONAL

Stand the hopper upright with the cone flat on the floor. Align the bolt holes in the top (4) corners. Secure with (4) Short M6 Bolts and (4) M6 Lock Nuts. Hand tighten only

Place the (4) leg brackets against the corner bracket mounting holes as shown, align the holes and insert (2) short M8 bolts from the outside of each leg bracket into the hopper. Secure with a hand-tight M8 lock nut on each bolt (8).

Go back and tighten all previously installed bolts. M6 bolts will require a 10mm wrench, M8 bolts (leg bracket) will require a 13mm wrench.
Note: Do not overtighten.

Install the Face Panel Tabs (2) to both the face panels, using a short M6 bolt and a lock nut. Tighten with a 10mm wrench. The “lip” should point upwards to create a hanger for the lidhandle while filling feeder.

ASSEMBLE & INSTALL THE LEGS

1. Collect all 4 Top-Leg sections. Insert each section into a leg bracket. Set the leg angle to eithe
   

2. Insert the remaining leg sections into the (4) top-leg sections. Tap firmly on the end of the legs when joining leg sections; this will help to keep them locked together.
   

INSTALL FEEDER KIT ONTO HOPPER

See additional feeder kit instructions for installation.

INSTALL INTERNAL FUNNEL

After installing your feeder kit onto your hopper, insert the internal funnel into the hopper, letting the self-alignment ring lock it into place at the bottom of the hopper cone.

NOTE: Make sure internal funnel is fully seated at hopper exit, and placed at the very bottom of the hopper. Funnel alignment is critical to proper feeder operation.

ASSEMBLE & INSTALL THE LID

1. Install the Lid Tabs (2) to the mounting holes on the lid by inserting a short M6 bolt from the INSIDE of the lid and securing with a lock nut tightened with a 10mm wrench. These will enable you to lock your feeder lid using most standard locks.
   

2. Place the lid assembly on top of the feeder with the tabs aligned. The handles should be on the sides of the feeder
   

Our Service Department will gladly answer any questions you have. www.moultriefeeders.com/support

References

• New Item Warranty | Moultrie Warranty Policy | Learn More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>