MOULTRIE MFA-15065 Ranch Series Dual Chute Instruction Manual

: June 1, 2024
: MOULTRIE

Table of Contents

MFA-15065 Ranch Series Dual Chute
Product Specifications
Product Usage Instructions
Assemble the Dual Chute
Maintenance
- Frequently Asked Questions (FAQ)
Q: How often should I clean the Dual Chute?
Q: Can I adjust the length of the feed tubes?

MFA-15065 Ranch Series Dual Chute

“`html

Product Specifications

Model: Moultrie Ranch Series Dual Chute
Warranty: 1-year warranty
Manufacturer: Moultrie

Product Usage Instructions

Assemble the Dual Chute

Remove all parts and hardware from packaging.
Align one pre-assembled feed tube with a diverter outlet and
slide it upward until the holes align.
Secure the Feed Tube to the Diverter using a Wing Bolt.
Repeat the process for the other Feed Tube and diverter
outlet.
Slide the diverter over the auger kit outlet with the beveled
side facing away from the auger kit.
Secure the diverter to the auger kit using a Hex Bolt, Flat
Washers, and a Hex Nut.
Adjust the length of the tubes by loosening the lower Wing
Bolt, sliding the tube to the desired length, and tightening the
Wing Bolt.

Important: Disconnect the battery or power
source before working around the feeder outlet.

Maintenance

The Dual Chute may need periodic cleaning to ensure proper
operation and cleanliness. Follow these steps:

Remove the tubes.
Rotate or replace them as needed for cleaning.
Reinstall the tubes onto the feeder.

Tip: Remember to reconnect the battery or power
source after maintenance for normal operation.

Frequently Asked Questions (FAQ)

Q: How often should I clean the Dual Chute?

A: It is recommended to clean the Dual Chute periodically
depending on your feed type and environment to ensure proper
operation.

Q: Can I adjust the length of the feed tubes?

A: Yes, you can adjust the length of the feed tubes by following
the instructions provided. Loosen the lower Wing Bolt, slide the
tube to the desired length, and then tighten the Wing Bolt
securely.

If you have any further questions or need assistance, please
contact our Service Department at
www.moultriefeeders.com/support.

“`

Instructions for Ranch Series Dual Chute
Thank you for your purchase of a Moultrie Ranch Series Dual Chute. Please read this sheet before operating the unit. If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet. Allow us to better serve you by activating your 1-year warranty online at http://www.moultriefeeders.com/warranty .

Wing Bolt M6 x 1 x 16mm QTY: 4*

Flat Washer M6 QTY: 4*

Hex Nut M6 x 1 QTY: 1

2 flat washers and 2 wing bolts are pre-installed in the feed tubes
A ASSEMBLE THE DUAL CHUTE

Hex Bolt M6 x 1 x 120mm QTY: 1

Remove all parts and hardware from packaging.
Align one of the pre-assembled feed tubes with one of the diverter outlets and slide the tube upward until the holes align. The tube should be oriented like the pictures below so that the first hole in the tube is aligned with the threaded hole in the diverter.

Diverter Feed Tube

Holes aligned

Secure the Feed Tube to the Diverter using a Wing Bolt in the holes you aligned in the last step. Wing Bolt

Repeat previous to install the other Feed Tube to the remaining diverter outlet.

WARNING: make sure battery/power source is disconnected before working around the feeder outlet.
With the beveled side of the diverter facing away from the auger kit, slide the diverter over the auger kit outlet until the holes are aligned and then secure the diverter to the auger kit using a Hex Bolt, (2) Flat Washers and a Hex Nut.

Bevel facing away from kit

Hex Nut Flat Washer

Hex Bolt Flat Washer

Now that the Chute is installed onto the feeder, the pre-assembled tubes can be adjusted to fit your feeding setup.
a. Remove the top Wing Bolt on the tube you want to adjust, this will allow you to rotate it around the diverter to point in the desired direction (adjustable in increments of 45°). When the tube is pointed correctly, reinstall the Wing Bolt and tighten until secure.

Remove

Rotate

Replace

b. To adjust the length of the tube, loosen (don’t remove) the lower Wing Bolt until the extension tube is moveable. Slide the extension tube until it is at the desired length then tighten the lower Wing Bolt until the tube is secure.

Loosen

Tighten

Extend
The Dual Chute is now customized to your feeding setup and fully installed to your Auger feeder kit. Depending on your feed type and environment, the Dual Chute may need to be cleaned periodically to ensure proper operation and cleanliness.
TIP: Remember to reconnect battery or power source to resume normal operation.

Our Service Department will gladly answer any questions you have. www.moultriefeeders.com/support
08072023 / MFG-15065