valera 542.06/044.04 Action Protect 1600 black Instruction Manual

: June 9, 2024
: Valera

Table of Contents

DIMENSIONS
OVERVIEW
ASSEMBLY AND OPERATING INSTRUCTIONS – Original instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

valera 542.06044.04 Action Protect 1600 black

valera 542.06/044.04 Action Protect 1600 black

DIMENSIONS

Dimensions

OVERVIEW

Overview

ASSEMBLY AND OPERATING INSTRUCTIONS – Original instructions

Read these instructions thoroughly. Available also on www.valera.com

CAUTION

For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.
Make sure the electrical system is fitted with a device which guarantees omni polar disconnection from the electricity mains under category III overvoltage conditions.
Make sure the unit is perfectly dry before using it.
WARNING: Do not use this appliance near bathtubs, showers, basins or other vessels containing water.
This hairdryer must be fixed so that a person taking a bath or shower cannot reach the handle, considering the cord at maximum extension.
This appliance can be used by children from 8 years of age and over, and by persons with limited physical, sensory or mental abilities or who lack the relevant experience and knowledge, if they are suitably supervised or have been educated to use the appliance safely and made aware of the associated risks.
Do not allow children to play with the appliance.
Children must not perform cleaning and maintenance procedures unless supervised.
Do not use your unit if it is not working properly. Do not try to repair this electrical unit yourself, rather contact an authorized technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
Plug the hairdryer into an alternating current outlet only, and make sure that the voltage of your electricity supply is the same as that indicated on the rating plate of the appliance.
Do not immerse in water or other liquids.
ever put the appliance in a place where it could fall into water or in other liquids.
Do not try to salvage an electrical appliance which has fallen into water.
Turn the unit off when you put it down.
Unplug the appliance when not in use, but never do it by pulling the cord.
Remember to check regularly that the air inlet and outlet grills are clean.
Allow your appliance to cool before storing away and do not wrap the supply cord around the hairdryer in storage.
The A-weighted sound pressure level of the hairdryers for commercial use is below 70 dB(A).

INSTALLATION INSTRUCTIONS

Wall holder model 044.01 – 044.02 –
044.03 – 044.04 – 044.05 – 044.06

Model 044.01 (Fig. 1)

Basic model with ON-OFF switch.
Model 044.02 (Fig. 2)

Model with 16 A European standard socket and ON-OFF switch.
Model 044.03 (Fig. 3)

Model with 10 mA () differential switch, 16 A European standard socket and ON-OFF switch.
Model 044.04 (Fig. 4)

Model with 10 mA () differential switch and ON-OFF switch.
Model 044.05 (Fig. 5)

Model with universal shaver socket () and ON-OFF switch.
Model 044.06 (Fig. 6)

Model with 10 mA (*) differential switch, universal shaver socket () and ON-OFF switch.
*() The appliance is equipped with a 10 mA differential switch.
() A safety transformer isolates the shaver socket from the mains electricity and a protective device prohibits the use of appliances with a power greater than 20 VA.

Installation of wall holder

This work should only be carried out by a suitably qualified electrical engineer, in order to comply with the existing national safety regulations. When the spiral cord is extended to its maximum length, the hairdryer shall not be reached by a person using the bath or the shower. There are two possible methods of installation

A = for fixed connection lead
B = for mobile connection lead

Attention: before installing the hairdryer always switch off the general switch of your mains electricity.
Method A (for fixed connection lead) for wall holder model 044.01 – 044.04 044.05 – 044.06

The connection wiring from the mains for wall holder models 044.01 – 044.04 – 044.05 – 044.06 must be type 2×1,5 mm2

Separate the cover (1) of the wall holder from the back plate by loosening the screw (14).
Remove the knockout (2) provided in the back plate of the wall holder.
Feed the mains supply cable (3) coming out of the wall into the hole in the back plate left after removing the knockout (2).
Secure the back plate of the wall holder to the wall using the plugs and screws provided.
Remove the terminal connector (4), connect the mains supply cable (3) to the terminal connector (4), as shown in the picture, and then secure again the terminal connector (4).
Model 044.01 – 044.04 – 044.05 – 044.06 are double insulated and no earth connection is provided.
Fit the front cover of the wall holder, taking care to locate the cable sleeve (6) properly. Secure the front cover with the screw (14).
Switch on the general switch of your mains electricity. The hairdryer is ready for use

Method B: (for mobile connection lead) only for wall holder model 044.01 – 044.04 044.05 – 044.06

The connection wiring from the mains for wall holder models 044.01 044.04 – 044.05 – 044.06 must be type H05VV-F 2×1,5 mm2 .

Separate the cover (1) of the wall holder from the back plate by loosening the screw (14).
Remove the knockout (8) provided in the base of the back plate of the wall holder for feeding the cable sleeve (11).
Secure the back plate of the wall holder to the wall using the plugs and screws provided.
Strip the power supply connection cable (13), insert the cable bushing (11), remove the terminal (9), connect the cable (13) to the terminal (9) and reposition the terminal (9). Position the stripped part of the cable carefully, as indicated in the picture. Secure the cable bushing (10) using the corresponding screws. Caution: this appliance has double insulation and is not fitted with an earthing system.
Locate the cable sleeves (6) and (11) in the slot provided in the base of the back plate.
Fit the front cover of the wall holder, taking care to locate the cable sleeves (6) and (11) properly.
Secure the front cover with the screw (14).
Switch on the general switch of your mains electricity. The hairdryer is ready for use.

Method C (with mobile connection) for models 044.02 – 044.03

See Method B: only variant:

The power cable for mounts 044.02 – 044.03 must be type H05VV-F 3G x 2.5 mm2 and must be connected to the tripolar terminal (7)

OPERATING INSTRUCTIONS

Switching

Wall mount switch (Fig. 7, 1) appliance placed in the mount = off appliance out of the mount = on

Differential switch (Mod. 044.03, 044.04, 044.06 only)

The differential switch (Fig. 9 and 10), in the event of a fault in the electrical circuit to which it is connected, is triggered and cuts off the power supply to the mount and the hair dryer. (Fig. 9)

After checking and resolving the fault, simply set the switch (1) back to the “I” position (Fig. 10, 1) to restore the power.
CAUTION: If you cannot reset the switch, contact an authorised technician to check the appliance.

Hairdryer Mod. 533.03 – 533.03/I – 533.05 533.05/I – 542.05 – 542.06 – 542.07 – 542.10 542.14

Blue pushbutton| ON = On/Off (pressure must be maintained to operate the hairdryer)
---|---
Slide Switch| Cool = (low power)
1 = (medium power)
2 = (maximum power)

Hairdryer Mod. 533.04 – 533.06

Grey pushbutton| = On / Off (pressure must be maintained to operate the hairdryer)
---|---

Hairdryer Mod. 561.02 – 561.17 – 561.20 561.22 – 561.23

Pushbutton	ON = On/off (pressure must be maintained to operate the hairdryer)
Left switch	0 = Off

1 = Low air speed
2 = High air speed
Right switch| Cool = Low air temperature
1 = Medium air temperature
2 = High air temperature

Hairdryers Mod. 586.09 – 586.09/I – 586.10 586.10/I -586.11 – 586.14 – 586.14/I

Hairdryer button ON = on/off (press and hold to run the appliance)

Airflow| 0 = Off
1 = Light airflow
2 = Strong airflow
---|---
Temperature| 1 = Warm air
2 = Hot air
3 = Very hot air

PRODUCT CARE

The hairdryer requires no special care or attention. You can clean your appliance with a cloth dampened with water. The cleaning of hairdryers with detergents, solvents, alcohol and other chemical products is strictly prohibited. When necessary, the air inlet grill should be cleaned with a soft brush or by vacuum cleaner.

Important

This hairdryer conforms to the safety regulations regarding electrical appliances. This hairdryer has a safety cut-out which will operate in case of overheating. The dryer will re-set itself after being left to cool for a few minutes, but please check air inlet and outlet grills are clear before continuing to use the dryer.

IMPORTANT

The hairdryers listed in these instructions for use, except for mod. 586.10, 586.10/I, are NOT suitable for installation or use in public areas, gyms, wellness/fitness centres, clubs, spas, etc. with high or low frequency of users. They are only suitable for installation and use in private rooms/bathrooms in hotels, guesthouses, homes and ship’s cabins.

This appliance conforms to European Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, 2015/863/EU, 2009/125/EC, 2012/19/EU and Regulation (EU) No. 1275/2008.

GUARANTEE

VALERA guarantees the appliance you have bought at following conditions:

The guarantee conditions for this appliance are as defined by our dealer in the country of sale. In Switzerland and the countries of the European Union, the warranty period is 24 months if the final purchaser is a private person (domestic use) and 12 months if the final purchaser is a company or business or professional (professional use). The guarantee period starts from the date of purchase as stated on the present guarantee card regularly filled out and stamped by the dealer or on the sale’s invoice.
The guarantee is applicable only against submission of the present guarantee card or the sale’s invoice.
The guarantee covers the elimination of all defects arisen during the guarantee period resulting from proven faults in material or workmanship. The elimination of the defects will be made either by repairing the appliance or exchanging it. The guarantee does not cover any damage arising from incorrect connection to the power supply, improper use, breakage, normal wear and noncompliance with the Instructions for Use.
All other claims of any nature, including those for eventual damages outside of the appliance, are excluded, unless our liability is legally mandatory.
The guarantee service is carried out free of charge; it does not affect the expiry date of the guarantee.
The guarantee becomes void if repairs are under-taken by unauthorized persons.

For UK only: this guarantee in no way affects your rights under statutory law.
In case of defect, please return the appliance well packed and together with the guarantee card regularly dated and stamped to one of our Valera Service Centres or to the dealer who will send it to the official importer for the guarantee service.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product indisposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

VALERA is a registered trade mark of LIGO PATENTS SA – Switzerland