pdp gaming 500-180 Controller Mount Nintendo Switch Grey User Guide
- June 9, 2024
- pdp gaming
Table of Contents
**pdp gaming 500-180 Controller Mount Nintendo Switch Grey User Guide
**
Items Included with the Joy-Con Charging Grip Plu
- Lighting Feature
- Getting Started
- Installation
- Charging
- Removal
- 2-Year Limited Manufacturer’s Warranty Information
A: Charging Grip
B: USB Type C Charging Cable
C: Quick Start Guide
Once you connect the Joy-Con Charging Grip Plus to a power source, the LED
indicators on the bottom of the grip will turn on and begin flashing. The
individual charging indicators let you know the charge status of each Joy-Con
controller. Once fully charged, the lights will remain solid.
Installation
Follow the steps below to install your Joy-Con controllers into the Joy-Con Charging Grip Plus:
- Take the empty grip out of the box and locate the latch on the top.
- Slide it to the right to release the hatch.
- Take a Joy-Con controller and align the rail on the side with the groove on the inside of the grip.
- Slide down until the bottom of the controller is flush with the bottom of the charging grip.
- Repeat these steps with the other Joy-Con controller.
- Once both controllers are in the grip, lift the hatch up towards you and then press the hatch down until you hear a small click. The Joy-Con controllers will then be secured in the grip and ready to use.
Charging
To charge your Joy-Con controllers using the Joy-Con Charging Grip Plus,
ensure both controllers are secured in the grip and simply connect the
included USB Type C cable into the charging port (located on top of the grip).
Then, plug the other end of the USB Type C cable into a USB port. The LED
Charging indicators will begin blinking and show the respective charge status
of each Joy-Con controller
Removal
Follow the steps below to remove your Joy-Con controllers from the Joy-Con Charging Grip Plus:
- Slide the latch, on top of the charging grip, to the right and then push the hatch down.
- Push the controllers halfway up from the bottom, then pull the rest of the way out from the top.
- Repeat these steps to remove the other Joy-Con controller.
CLASS B EQUIPMENT
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is Connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
LIMITED WARRANTY
Coverage and Term PDP warrants that this product will be free from
manufacturing defects for two years from the original date of purchase.
Manufacturing defects are those defects in materials and/or workmanship,
subject to final determination by PDP’s customer service department. This
warranty applies only to original purchasers with a valid proof of purchase
from an authorized PDP retailer that clearly shows the date of purchase.
Exclusive Remedy and Exclusions The exclusive remedy for valid claims
will be the replacement, or refund of the product. This warranty does not
cover defects caused by accidents, improper or abusive use of the product,
unauthorized or improper modifications, repairs, or handling
How to Get Service Purchasers with product issues should not return the
product to the store, but instead contact PDP’s customer service department
first. You can contact PDP customer service by phone at
1-800-331-3844 (US and Canada only),
Monday to Friday from 8 AM to 6 PM PST. International customers can contact us
by phone at +442036957905. You can always reach us, 24/7, by visiting
support.pdp.com and clicking the “Submit a Request” button top right of the
page to open a support ticket. Inquiries are typically answered within 24
business hours.
Your Rights Under Applicable Law This warranty does not affect the legal
rights of customers under applicable state, provincial, or national laws
governing the sale of consumer goods.
Additional Information for Australian Consumers PDP products come with
guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure. The benefits given to you
under our express warranty are in addition to other rights and remedies you
have under the Australian Consumer Law and other laws.
2-Year Manufacturer’s Warranty: For product issues and guidance contact us instead of returning to the store.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>