wet sounds a link plus Hybrid Receiver Owner’s Manual

: June 9, 2024
: wet sounds

Table of Contents

wet sounds a link plus Hybrid Receiver
controls / indicators
essential functions
LED indicators
installation
other features
a link plus user’s guide
Documents / Resources

wet sounds a link plus Hybrid Receiver

controls / indicators

Congratulations!
Thank You for purchasing the Wet Sounds a link plus kit!
Wet Sounds products represent the ultimate in high performance, element-proof audio.
Wet Sounds products are specifically designed and engineered to withstand the rigorous marine and outdoor environments.
The Wet Sounds a link plus is a wireless audio link that allows broadcasting from one audio system to another. Each a link plus can be set to either send or receive audio as needed.
Up fo four (4) a link plus units can be bonded to receive the same audio from one (1) broadcasting a link plus, allowing for a shared expenence through mulfiple auadio systems.
Please take a moment to look over this owners manual before enjoying the product.

essential functions

powering on and off

To power on a link plus, simply press and hold the Power Button for about one (1) Second.
To power off a link plus, press and hold the Power Button until LEDs turn off.

bonding your a link plus
Each a link plus will be set to Receive when initially powered on. To use a link plus, one (1) of the units must first be set for Transmit.

The set one (1) a link plus for Ironsmith, simply fap the Power Button after the unit is powered on. The Status LED will change from green to red. Your a link plus units will automatically Bond, and are now ready to broadcast audio.”

Tapping the Power Button one (1) time will switch a link plus between Transmit and Receive at any fame.

If your a link plus units do not automatically Bond the Transmitting a link plus is already a Favorite on your Receiver’s Favorites List. In this case, switch the Receiving unit to Favorites Mode (] 1 click), and it should automatically find the Favorite Transmitter and Bond to it.

favorites list and explore mode
While Receiving, a link plus uses a Favorites List for storing Transmitters you have Bonded to before. a link plus will automatically add any Transmitter to your Favorites List if Bonded for it tor 30 minutes.

To access your Favorites List, switch the Receiving unit to Favorites Mode at any time by clicking the button one (1) time.

To manually add or delete the Transmitter you’re currently Bonded with to/from your Favorites List, simply hold the button for a few seconds.

To rotate through your Favorites List, click the button one (1) time to go to your next Favorite.

a link plus can also be set to Explore Mode, to search for new, unknown Transmitters. To enter Explore, click the button two (2) times.

LED indicators

installation

In order to ensure optimal performance and range, a link plus should be mounted with the top half of the housing placed above all body panels, windows. roll bars etc.

a link plus comes with two (2) suction cups for each unit that can be installed in the cradle for easy mounting to glass or other smooth, glossy surfaces.
To install, insert suction cup head into larger, fop hole of cradle and slide up. SUction cup will lock into place when seated properly. repeat for lower suction cup, sliding down to lock.
(verify both the mounting surface and SUction cups are clean before mounting to ensure proper adhesion).

For permanent mounting or mounting to rough surfaces, the cradle can be hard- mounted using M6 or #10 screws (not included) in thee indicated locations. lightly hand tighten hardware, so as not to crack the cradle.

other features

a link plus features an integrated cradle, which is attached with a slide-lock feature.

The SKAA Compatible Badge as well as the graphics- only version of it, the SKAA lion, both found on the Product itself, certify that this Product has been tested and is fully compliant with all of the requirements of the SKAA Standard and has been granted SKAA Certification. This Product will work seamlessly with other products in the SKAA ecosystem of audio transmitting and receiving devices. For more information on the SKAA Standard, please visit www.SKAA.com. The SKAA® name as well as its associated marks, logos and icons are trademarks or registered trademarks of Eleven Engineering Incorporated.

a link plus user’s guide

Each alink plus Receiver has a Favorites LisŤ which remembers your Favorife a link plus Transmitters. A green Bond LED on your a link plus Receiver means you’re listening to a Favorite, or searching for one. Your a link plus Receiver can also Explore to find new a link plus Transmitters – an amber Bond LED means you are searching for Transmitters which are not on your Favorites List. A Cluster is a group of two or more a link plus units that behave as one, similar to a left and right speaker pair. The Bond Button g) allows you to select which a link plus you’re listening to.

QUESTIONS AND ANSWERS