ikan PT4900-PTZ Professional 19 Inch High Bright PTZ Compatible Teleprompter User Guide
- June 9, 2024
- ikan
Table of Contents
- PT4900-PTZ Professional 19 Inch High Bright PTZ Compatible Teleprompter
- OVERVIEW
- What’s Included
- Teleprompter Assmebly Setup
- Monitor Menu Settings
- TELEPROMPTER SPECS
- MONITOR SPECS
- Optional Accessories
- Assembly Steps
- Attaching the Talent Monitor
- Specifications
- Optional Accessories
- CONDITIONS OF WARRANTY SERVICE
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
PT4900-PTZ Professional 19 Inch High Bright PTZ Compatible Teleprompter
User Guide 
Quick Start Guide
PT4900-PTZ Professional 19 Inch High Bright PTZ Compatible Teleprompter
PToH900-PTZ
Profesional 19” High-Bright PTZ-Compatible Teleprompter
OVERVIEW
The 19” PTZ Teleprompter from Ikan is a professional solution for
teleprompting with PTZ cameras. The package provides an extra-wide hood
assembly to allow considerable movement of the camera within the wide beam
splitter glass. The PTZ Teleprompter features a 19” 1000 cd/ mz? monitor,
70/30 20”-wide beamsplitter glass, and a 25’ reading range. The teleprompter
is designed for use with a wide range of PTZ cameras, a s the wide
beamsplitter provides for a wide amount of left-right panning. The
teleprompter includes a base system that can be easily shifted forward and
backwards, which enables mounting the camera to the prompter without requiring
counterweights.
Please note that the PTZ4900-PTZ includes parts to build two types of
teleprompter systems, a standard 19” Teleprompter that is compatible with
various types of mirrorless and broadcast cameras, and a 19” PTZ teleprompter
that is compatible with a wide range of PTZ cameras. This Quick Start Guide
will show you how to set up the 19” Teleprompter for PTZ cameras. For
instructions on how to set up the PT4900 for broadcast o r mirrorless cameras,
please refer to the PT4900 Quick Start Guide on our website.
What’s Included
Teleprompter Assmebly Setup
Step 1
Place the Hood Attachment Frame over the Glass Holder. Then place the glass
against the Glass Holder. Make sure the screws pass through the holes on the
both the Hood Attachment Frame and the Glass Holder.
Step 2
Secure the Glass Holder b y fastening the knurled nuts to the screws as
pictured below. 
Step 3
Remove the monitor mounts from the teleprompter base using the included larger
4mm hex key to loosen from the 15mm rods.
 Step
4
Put the washers on before tightening the screws. The washers and 4 additional screws are inside a bag on the bottom foam.
Step 5
After the monitor mounts are attached, adjust the 15mm rods to accommodate the
monitor. Leave about 1 inch of room for the teleprompter bracket. Make sure
the 15mm rods go through both set of monitor mounts. Please ensure that all
screws are properly tightened after inserting the monitor. SAFETY NOTE Make
sure to leave at least 2 inches of the rods inside the teleprompter base.
Step
6
While sliding the teleprompter bracket into the slot of the Glass Frame Holder Bracket, pull on the red knob to allow the bracket to fully slide in. Step 7
Once the bracket is in place, tighten the side screw to lock i n place. Double check and make sure all the screws are tightened with the included hex keys.
 Step
8
Fold the flaps of the Hood alongside the edges of the Hood Attachment Frame. The flaps of the Hood are magnetic so they will automatically attach. Connect the bottom part of the hood by attaching the magnetic flap to glass frame holder. Connect the velcro straps to the sides of the hood.
Step 9-A: Connecting the PTZ Riser to the Ikan OTTICA
To connect the PTZ Camera Riser to the Ikan OTTICA camera, fasten the %4-20
screw on the PTZ Riser Plate to the thread on the bottom of the OTTICA camera.
Step 9-B: Connecting the PTZ Riser to other PTZ Cameras
To connect the PTZ Camera Riser to the other PTZ cameras, Remove the plate on
top of the PTZ Riser by unfastening the f o u r screws on the surface of the
plate. Once the plate has been removed, fasten the 4-20 screw on the PTZ Riser
Plate to the thread on the bottom of the PTZ camera. 
Step 10
Set the PTZ camera inside the hood b y aligning the screws on the riserplate
to the slot on the Base. O n c e the screws are aligned, S l i d e the r i s e
r plate
into the Base.
Step 11
To prevent light from leaking through the hood, seal both zippers down, attach
the velcro straps along the back and sides of the hood. Connect the cables to
the back of your PTZ camera by putting the m through the slot on the back of
the PTZ Hood. Once your cables are connected, tighten the draw string on the
back of the PTZ Hood.
Step 12
Mount your own tripod plate to the bottom plate by aligning the 1/4-20 and/or
3/8-16 screws and fastening them to the Bottom Plate . It is recommended that
you connect your tripod plate to front of the Bottom Plateso that you can
balance your teleprompter easier. Once your tripod plate is connected to the
Bottom Plate , mount the tripod plate to your tripod head.
Step 13
In order to properly balance the teleprompter , loosen the 4 screws on the bottom plate and slide the entire teleprompter system back or forward until the center of gravity has been determined. Once the center of gravity has been determined, tighten the thumb screws to keep the base from sliding.
Step
14
To secure your teleprompter system, insert the included headless screws into the threads behind and in front of the Base.
Step 15
The headless screws should be inserted to the threads as pictured below.
Monitor Ports
BNC — AV Composite Input
VGA — Video Graphics Array D E 1 5 Connection
HDMI — High-Definition Multimedia Interface Input Connection
Power Port — 12-24v Input
HDMI — Switch HDMI input
VGA — Switch to VGA input
AV — Switch to composite BNC input
Flip — Toggle image flip( Can be set to horizontal , vertical, o r both via
menu)
Up Arrow — Toggle u p to adjust setting
Menu — Access to monitor settings
Down Arrow — Toggle down to adjust setting
Monitor Menu Settings
Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup — Manually configure RGB Return
System Contig
Menu Duration — Set duration of how long menu stays on screen
Video Ratio — Set screen aspect ratio 16:9 o r 4:3 (4:3 is native resolution,
16:9 will create black bars)
Flip-H — Assign toggle button to flip image horizontally
Flip-V — Assign toggle button to flip image vertically
Reset — Factory reset Return
PC Set up (Only available for VGA)
H-Position — Adjust horizontal position
V-Position — Adjust vertical position
Auto — Monitor automatically adjust position Return Exit
How to set-up FLIP button feature:
- Press MENU button
- Navigate to SYSTEM CONFIG.
- Navigate to FLIP-V or FLIP-H
- Change FLIP-V and/or FLIP-H to “ON”
- Exit MENU
- The FLIP button should now be activated and can be pressed t o mirror the image Horizontally or Vertically
- When FLIP-H is ON, the image will flip Horizontally
- When FLIP-V is ON, the image will flip Vertically
- If both are ON, the FLIP button will toggle both Horizontal and Vertical flip
Watch our VIDEO TUTORIAL o n how to assemble Ikan Professional Telepromopters:
https://youtube.com/playlist?list=PLcjaK5n9Y8ctrbYS3t2g4nyx2uADOXjuF
Specifications for PT4900-PTZ
TELEPROMPTER SPECS
Riser Plate Height| Low: 2.06 in./52.5mm
Medium: 3.74 in./95mml High: 5.31 in./135mm
DSLR: 6.29 in./160mm
---|---
Length of Rods| 15mm x 400mm
Build Material| Chassis: Anodized Aluminum
Rods: Carbon Fiber
Reading Range| 25 ft. / 7.62 m
Beamsplitter Ratio| 70/30
Beamsplitter Shape| Rectangular
Beamsplitter Material| Glass
Tripod Mounts| 11 x 1/4 in. -20 Female I 9 x 3/8 in. -16 Female
Product Weight w/ Low Plate| 22.70 lbs.
Product Weight w/ Medium Plate| 23.10 lbs.
Product Weight w/ High Plate| 23.23 lbs.
Product Weight w/ DSLR Plate| 22.60 lbs.
Height of Teleprompter| 16 in./ 406mm
Angle of Glass Frame Holder| 50°
Material of Hood| Polyester Canvas
Material of Riser Plates| Aluminum
Material of Glass Frame Holder| Aluminum
MONITOR SPECS
| Aspect Ratio | 4:03 |
|---|---|
| Maximum Brightness | 1000 cdlm2 |
| Screen Size (Diagonal) | 18.5 in. |
| Mount | VESA 100mm |
| Video Inputs | AV COMPOSITE, HDMI, VGA |
| Input Voltage | DC 12v / 4A |
| Power Consumption | 21W |
| Product Weight | 6 lbs. |
| Product Dimensions | 17 in. x 15 in. x 1 in. |
| Native Resolution | 1280 x 1024 |
| Viewing Angle | 160° (H) / 170° (V) |
| Build Material | Aluminum Chassis |
| Image Flip | Horizontal: Yes I Vertical: Yes |
Optional Accessories
PT4900-GM- Replacement Glass for PT4900
PT19W-TALLY – 19” Widescreen Talent Monitor w/ Tally Add-on Kit for
PT4900
PT-PEDAL -Teleprompter Foot Control Pedal
PT-CASE-V2 – Rolling Hard Case for PT4900 Teleprompter
Foam Case
To make your teleprompter m o r e portable, we packed it in are usable, high-
quality foam.
The shape and size of the foam was designed to fit into Ikan’s PT-CASE-V2.
Talent Monitor Add On Kit for PT4900
What’s Included
- 1 x Teleprompter Monitor w/ Aluminum Chassis
- 1 x Power Adapter with Cable
- 1 x VESA Monitor Mount
- 1x 15mm Rod Adapter
- 1x Mounting Knob
- 4x 10mm Screws
- 4x 15mm Screws
- 2x Large Screws
- 4x Riser Washers
- 1 x Adjustable Plate
Assembly Steps
Setting Up the Talent Monitor
Using the shorter 4 x 10mm Screws, attach the VESA Monitor Mount. Make sure
that the long end of the VESA Monitor Mount is pointing i n the direction of
the power button like the image above. Use the Mounting Knob to tighten the
15mm Rod Adapter to the VESA Monitor Mount.
Setting Up the Teleprompter Monitor (Monitor from the PT4900)
If the mounting brackets where previously installed on the teleprompter
monitor, r e m o v e those screws. Using the longer 4 x 15mm Screws and 4x
Riser ashers attach the mounting brackets with the washers between the
bracket and monitor like the image below.
Attaching the Talent Monitor
After both the talent monitor and teleprompter monitor are set up, slide the
talent monitor on to the PT4900.
WARNING We recommend at least1 inch of rod should be left inside the
teleprompter base. 
Specifications
PT19-TM
19” High-Bright Teleprompter Monitor
| Aspect Ratio | 4:03 |
|---|---|
| Brightness | 1000 cd/m2 |
| Screen Size | 19″ |
| Video Inputs | Composite BNC, VGA, HDMI |
| Input Voltage | DC 12v / 4A |
| Power Consumption | 10 w |
| Product Weight | 12 lbs |
| Product Dimensions | 17″ x 15″ x 1″ |
| Native Resolution | 1280 x 1024 |
| Shipping Weight | 14 lbs |
| Shipping Dimensions | 24″ x 20″ x 4″ |
| Viewing Angle | 160° (1-1) /170° (V) |
| UPC | 847983033201 |
| Build Material | Aluminum Chassis |
Supported Video Signals
HDMI
720x480i & 720x480p @ 59.94, 6 0 Hz
720x576i & 720x576p @ 50 Hz
1280x720p @ 50, 59.94, 6 0 Hz
1 9 2 0 x 1 0 8 0 i @ 50, 59.94, 6 0 H z
1920x1080psf @ 24, 25, 29.97, 30 Hz
1920x1080p @ 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 Hz
Optional Accessories
Some other products that work well with this item a vailable from Ikaninclude:
PT4900 19” High Bright Beam Splitter Teleprompter
Learn More
More dynamic information at official website:
www.ikancorp.com
Support
Contact email: support@ikancorp.com
CONDITIONS OF WARRANTY SERVICE
- Free service for one year from the day of purchase if the problem is caused b y manufacturing errors.
- The components and maintenance service fee will be charged if the warranty period is expired.
*Free Service will not be Provided in the Following Situations:(Even i f the product is still within the warranty period.)**
- Damage caused b y abuse o r misuse, dismantling, or changes to the product not made by the company.
- Damage caused b y natural disaster, abnormal voltage, and environmental factors, etc.
©2022 Ikan International. All rights reserved.
www.ikancorp.com
11.713.272.88221
sales@ikancorp.com
because we’re filmmakers too
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>