shop vac SH14-C450 12 Gallon Stainless Steel Wet Dry Vacuum Cleaner User Manual

10 U.S. GALLONS
37.8 LITERS
SERIES SH
HOUSEHOLD USE
User Manual

FOR YOUR SAFETY, READ ALL INSTRUCTIONS CAREFULLY BEFORE USE. SAVE THIS MANUAL FOR FUTURE REFERENCE.
*Tank capacity refers to actual tank volume, and does not reflect capacity available during operation.

CATALOG / MODEL NUMBERS

Catalog No. 5761011
Model No. SH14-C450
Date of Purchase:
For your records, please record your Date of Purchase and store this owner’s manual in a safe location for future reference.

CARTON CONTENTS

WARNING: REVIEW IMPORTANT SAFETY INSTRUCTIONS BEFORE USE.
Check to make sure you have the following:

1. Vacuum
2. Cartridge filter
3. Filter Retainer
4. Filter bag
5. Nozzle
6. Hose
7. Extension wands (2)| 8. Caster feet (4)
9. Casters (4)
10. Screws (4)
11. Foam sleeve
12. Hose holder (2)
13. Tool holder
---|---

TOOLS REQUIRED

Questions?
Visit www.shopvac.com 24 hours a day.

ATTENTION!
Read all safety rules carefully before attempting to operate. Retain for future reference.
DANGER!

Never operate this unit when flammable materials or vapors are present because electrical devices produce arcs or sparks that can cause a fire or explosion.
NEVER OPERATE UNATTENDED!

WARNING!
ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING THE TANK COVER.

WARNING!
ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT IN SERIOUS INJURY.

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

1. Do not leave the appliance when plugged in. Unplug from outlet when not in use and before servicing.
2. Do not expose to rain – store indoors.
3. Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
4. Use only as described in this manual. Use only the Manufacturer’s recommended attachments.
5. Do not use a damaged cord or plug. If the appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, contact Shop-Vac for assistance.
6. Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not unplug by pulling on the cord. To unplug, grasp the plug; not the cord.
8. Do not handle the plug or appliance with wet hands.
9. Do not put any object into openings. Do not use with any openings blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
10. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
11. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
12. Do not use without a dust bag and/or filters in place.
13. Turn off all controls before unplugging.
14. Use extra care when cleaning on stairs.
15. Do not use it to pick up flammable or combustible liquids such as gasoline or use it in areas where they may be present.
16. Do not use your cleaner as a sprayer of flammable liquids such as oil base paints, lacquers, household cleaners, etc.
17. Do not vacuum toxic, carcinogenic, combustible, or other hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides, or other health-endangering materials. Specially designed units are available for these purposes.
18. Do not pick up soot, cement, plaster, or drywall dust without a cartridge filter and collection filter bag in place. These are very fine particles that may pass through the foam and affect the performance of the motor or be exhausted back into the air. Additional collection filter bags are available.
19. Do not leave the cord lying on the floor once you have finished the cleaning job. It can become a tripping hazard.
20. Use special care when emptying heavily loaded tanks.
21. To avoid spontaneous combustion, empty the tank after each use.
22. The operation of a utility vac can result in foreign objects being blown into the eyes, which can result in eye damage. Always wear safety goggles when operating a vacuum.
23. STAY ALERT. Watch what you are doing and use common sense. Do not use a vacuum cleaner when you are tired, distracted, or under the influence of drugs, alcohol, or medication causing diminished control.
24. WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this may disperse fine lead particles into the air. This vacuum cleaner is not intended for use under EPA Regulation 40 CFR Part 745 for lead paint material cleanup.

SAVE THESE INSTRUCTIONS

WARNING!
DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING. UNPLUG THE UNIT WHEN NOT IN USE.

DOUBLE INSULATED APPLIANCE

This appliance is provided with double insulation. Use only identical replacement parts.
Servicing for Double Insulated Appliances A double insulated appliance is marked with one or more of the following: the words
“Double Insulation” or “Double Insulated” or the Double Insulation symbol. In a double insulated appliance, two systems of insulation are provided instead of grounding.
No grounding means is provided on a double insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel.
Replacement parts for a double insulated appliance must be identical to the parts they replace.

POLARIZATION INSTRUCTIONS

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

EXTENSION CORDS
When using the appliance at a distance where an extension cord becomes necessary, a 2-conductor cord of adequate size must be used for safety, and to prevent loss of power and overheating. Use TABLE A to determine the A.W.G. wire size required. To determine the ampere rating of your vacuum, refer to the nameplate located on the motor housing.
Before using the appliance, inspect the power cord for loose or exposed wires and damaged insulation. Make any needed repairs or replacements before using your appliance. Use only two-wire outdoor extension cords, which have two- prong non-grounding-type plugs and receptacles which accept the extension cord’s plug.
When vacuuming liquids, be sure the extension cord connection does not come in contact with the liquid.
NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS LOW. THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE FREQUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR WITH A CONSOLE OR INSTALLED HUMIDIFIER.

0 – 6 – – 10
6
10 12| 18
18
18| 16
16
16| 16
14
14| 141212

TABLE A

UNPACKING
Pull lid latches in an outward motion and remove the tank cover. Remove any accessories and literature that may have been packed in the vacuum tank.

ASSEMBLY CASTER SYSTEM ASSEMBLY

1. You will find four caster feet FIGURE 1, four casters FIGURE 2, and four screws with your wet/dry vacuum. Assemble as follows:

2. With the cord disconnected from the receptacle and the tank cover removed, turn the tank upside down so that the bottom is facing up.

3. With the tank drain facing you, take caster feet marked with the letter A, FIGURE 3, and place them in the slots on the left front and right rear of the tank also marked with the letter A.
   FIGURE 3

4. Secure with screws provided.
   FIGURE 4.

5. Take caster feet marked with the letter B and place on the right front and left rear of tank also marked with the letter B.
   FIGURE 5.

6. Secure with screws provided
   FIGURE 6.

7. Insert casters into feet by placing the stem of the caster into the holes provided. Apply pressure and twisting motion until casters snap into place.
   FIGURE 7.

8. With tank drain facing you, attach hose holder A to caster foot A, and hose holder B to caster foot B.
   FIGURE 8.

9. Apply pressure to the front of the hose holder to snap into place.
   FIGURE 9.

10. Return the tank to an upright position.
    TOOL HOLDER ASSEMBLY

11. With the rear of the unit facing you, take the tool holder and position it with tabs facing the rear of the unit.
    FIGURE 10.

12. Place “J” shaped tabs into the slots on cord wrap FIGURE 11. Press down until tabs snap into place.

13. Press down on the center of the tool holder until the tab latches on the bottom of the lid.
    FIGURE 12. GENERAL SET UP

14.  Before replacing the tank cover, refer to Dry Pick Up or Pick-Up Operation in the user manual to ensure you have the proper filters installed for your cleaning operation.

15. Replace the tank cover, and apply pressure with the thumb to each latch until it snaps tightly into place. Make certain all lid latches are clamped securely.

16. Insert machine hose end with locking-nut into the inlet of the tank. Turn to lock nut to tighten. Do not over-tighten.

17. Attach the extension wands to the accessory end of the hose. Twist slightly to tighten the connection.
    FIGURE 13.

18. Attach one of the cleaning accessories (depending on your cleaning requirements) to the extension wands.
    Twist slightly to tighten the connection.
    FIGURE 13.

19. Plug the cord into the wall outlet. Your cleaner is ready for use I = ON, O = OFF.
    NOTE: Many more useful tools are available at your local dealer or the Shop-Vac® website.
    Questions?
    Visit www.shopvac.com 24 hours a day.

FILTER INSTALLATION AND CLEANING

DRY PICK UP
NOTE: Never use the vacuum for dry pick up without a dry use filter installed on the lid cage. Using the vacuum without a filter will cause dust to discharge from the blower port and cause damage to the motor.
INSTALLING AND CLEANING THE CARTRIDGE FILTER:
WARNING!
ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING THE TANK COVER.
NOTE: If a foam sleeve (not standard with all models) is installed on the lid cage, remove it before installing the cartridge filter.

20. The cartridge filter can be used for dry pick up and small quantities of wet pick up. Installation is the same for both. When picking up large quantities of water we recommend using a foam sleeve (not standard with all models) instead of the cartridge filter. When picking up fine dust or powders a high-efficiency filter bag (not standard with all models) must be used with the cartridge filter.
    NOTE: If a cartridge filter has been used for wet pick up, it must be cleaned and dried before using it for dry pick up.

21. With the tank cover in an upside-down position, slide the cartridge filter down over the lid cage, pushing until the filter seals against the cover.
    FIGURE 14.

22. Place filter retainer on top of the cartridge filter.
    FIGURE 15.

23. Hold the tank cover with one hand, and turn the handle on the filter retainer clockwise to tighten, locking the filter into place.
    FIGURE 16.

24. To remove the filter for cleaning, again hold the tank cover and turn the filter retainer counter-clockwise to loosen and remove.
    FIGURE 17.

25. Slide the cartridge filter off the lid cage.
    FIGURE 18.

26. To clean the cartridge filter shake or brush off excess dirt.
    FIGURE 19.

27. Or rinse (from the inside of the filter) with water.
    FIGURE 20. Dry completely (approximately 24 hours).

28. Check the filter for tears or small holes. If none are found, reinstall the filter. To prevent damage to your vacuum, do not use a filter with a hole or a tear.
    WARNING!
    KEEP FILTERS CLEAN. THE EFFICIENCY OF THE VACUUM IS LARGELY DEPENDENT ON THE FILTER. A CLOGGED FILTER CAN CAUSE OVERHEATING AND POSSIBLY DAMAGE THE CLEANER. CHECK THE FILTER PERIODICALLY AND REPLACE IT AS REQUIRED.
    INSTALLING THE DISPOSABLE FILTER BAG:
    WARNING!
    ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING THE TANK COVER.

29. Use the disposable filter bag in conjunction with the cartridge filter for easy disposal of the debris. The bag is not required for normal dry pick-up. When picking up fine dust or powders a high-efficiency filter bag (not standard with all models) must be used.
    NOTE: Use for dry pick up only.

30. With the cord disconnected from the receptacle, pull latches in an outward motion and remove the tank cover.

31. Unscrew the hose locking nut and remove the hose from the inlet.
    FIGURE 21.

32. Remove the inlet defector from the deflector guide.
    NOTE: Hose must be removed before the inlet deflector can be taken out.
    FIGURE 22.

33. Position the inlet deflector with the opening facing the left or the right side of the filter bag. Slide the filter bag collar over the inlet deflector, matching the notches of the bag collar to the tabs on the inlet deflector. The bag will only fit properly one way.
    FIGURE 23.

34. Slide the inlet deflector with the filter bag attached to the deflector guide. FIGURE 24

35. Reinsert the hose into the inlet and tighten the locking nut.
    FIGURE 25.

36. When secured in place, expand the filter bag and position it around the inside of the tank. Replace tank cover.
    NOTE: When removing the filter bag from the tank, remove the inlet deflector from the filter bag collar. Reinstall the inlet deflector into the deflector guide. The inlet deflector must be in place for any type of cleaning.
    WARNING!
    FOR FINE DUST POWDERS
    When vacuuming fine dust, or powders of any kind (plaster, drywall dust, cold ashes, concrete dust, etc.) a high-efficiency drywall filter bag must be used. When vacuuming
    normal household dust and debris, standard household disposable filter bags may be used.

WET PICK-UP OPERATION

37.  Your vacuum can be used for wet pick-up. Remove ALL dirt and debris found in the tank. Remove all dry-use-only filters, including the filter bag, from the vacuum.

38. A clean cartridge filter may be used to pick up small quantities of liquid. To use the cartridge filter; follow the cleaning and installation instructions under dry pick up.

39. For vacuuming large quantities of liquid use a foam sleeve (not standard with all models). A foam sleeve may be purchased at your local Shop-Vac® distributor, on the Shop-Vac® website, or by contacting Shop-Vac® customer service. To use the foam sleeve; follow the installation instructions in this section.

40.  Misting in the exhaust air or dripping of liquid around the tank cover may occur if the filter becomes saturated during wet pick-up. If this occurs, remove the filter and allow to dry, or replace it with another dry filter.

41. Turn the unit off immediately upon completing a wet pick-up job or when the tank is full and ready to be emptied. When the tank is full, suction will drastically reduce. Refer to “automatic suction shut off” in this manual. Raise the hose to drain any excess liquid into the tank. Follow the “emptying liquid waste” section in this manual.

42.  Before storing the vacuum cleaner or using it for dry pick-up, clean and dry the interior of the tank and the underside of the tank cover. Clean and allow the filters to dry completely.
    NOTE: WET PICK-UP ACCESSORIES SHOULD BE WASHED PERIODICALLY; ESPECIALLY AFTER PICKING UP WET, STICKY KITCHEN ACCIDENTS. THIS CAN BE ACCOMPLISHED WITH A WARM SOLUTION OF SOAP AND WATER.
    FOAM SLEEVE INSTALLATION AND CLEANING:

43. With tank cover in an upside down position, slide foam sleeve down over lid cage pulling until foam sleeve completely covers lid cage.
    FIGURE 26.

44. To clean the foam sleeve, disconnect the plug from the wall outlet. Remove the tank cover and place the cover in an upside-down position. Remove the foam sleeve by sliding it up and off the lid cage.

45. Shake excess debris off of the foam sleeve with a rapid up and down movement.

46. Hold the foam sleeve under running water for a minute or two, rinsing from the inside of the filer. A water wash is not always required, depending on the condition of the foam sleeve.

47. Check the filter for tears. If any are found, replace them with a new filter.
    BLOWER FEATURE

48. Your vacuum can be used as a powerful blower. To use your unit as a blower, clear the hose of any obstructions. Insert hose end with locking nut into blower port and tighten the locking nut.
    FIGURE 27. Do not over-tighten. Caution should be used when using as a blower due to the powerful force of air when using certain attachments.
    NOTE: For best results, when vacuuming, remove the blower port cover.
    WARNING!
    ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT IN SERIOUS INJURY.

EMPTYING LIQUID WASTE FROM THE TANK

49. Your wet/dry vacuum can be emptied of liquid waste by removing the drain cap. To empty, turn the unit off and remove the plug from the wall receptacle. Remove the drain cap and deposit the liquid waste contents in a suitable drain. After the tank is empty, return the drain cap to its original position. To continue use, plug the cord into the wall receptacle and turn the unit on. Use side carry handles for lifting vac when draining tank into drains that are located above floor level.
    AUTOMATIC SUCTION SHUT OFF

50. The vacuum is equipped with an automatic suction shut-off that operates when picking up liquids. As the level of the liquid rises in the tank, an internal float rises until it seats itself against a seal at the intake of the motor, shutting off suction. When this happens, the motor will develop a higher than normal pitch noise, and the suction is drastically reduced. If this occurs, turn the unit off immediately. Failure to turn the unit off after float rises and shuts off suction will result in extensive damage to the motor. To continue use, empty the liquid waste from the tank as outlined in the previous section.
    NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION. IF THIS OCCURS, TURN THE UNIT OFF AND PLACE VAC IN AN UPRIGHT POSITION. THIS WILL ALLOW THE FLOAT TO RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE OPERATION.
    NOTE: FOR BEST RESULTS, WHEN VACUUMING, REMOVE THE BLOWER PORT COVER.

LUBRICATION

51. No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.

STORAGE

52. Before storing your vacuum cleaner the tank should be emptied and cleaned. The power cord can be wrapped around the cord wraps provided on the tank cover on the rear of the unit.
    FIGURE 28.

53. Accessories may be stored in the tool holder.
    FIGURE 29. The vacuum should be stored indoors.

TROUBLESHOOTING

BEFORE DOING ANY WORK ON YOUR VACUUM, TURN THE UNIT OFF AND DISCONNECT THE PLUG FROM THE WALL OUTLET.

filter. If the condition continues, change
filter.
Air leak| Check all fittings for a tight fit (nozzles, hose, etc.)
Check that the tank cover is sealed properly.
Obstruction in hose or nozzle| Check nozzle, hose, etc. for obstructions, and remove if present.
Misting in the exhaust air| Saturated filter| Replace the saturated filter with a dry filter.

LIMITED LIFETIME WARRANTY
This product has a Limited Lifetime Warranty. For Warranty Policy and Vacuum, Registration details go to:

|
---|---
https://www.shopvac.com/warranty| https://shopvac.com/register

Visit www.shopvac.com for your vacuum’s parts list schematic.
Shop-Vac Customer Service: www.shopvac.com/support
Contact Shop-Vac® Customer Service if any parts are missing or damaged.
SHOP-VAC
2323 Reach Road
Williamsport, PA 17701
www.shopvac.com
U.S. Patents Issued and Pending.
© 2022 Shop-Vac
USA, LLC.
All Rights Reserved.

References

• Shop-Vac Store - Genuine Shop-Vac Products
• Customer Service | Shop-Vac Store
• Register Your Shop-Vac® Product | Shop-Vac Store
• The Shop-Vac® Home Use Warranty | Shop-Vac Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>