PROJECT SOURCE JQY8113A 3-Light Chandelier Instruction Manual
- June 9, 2024
- PROJECT SOURCE
Table of Contents
PROJECT SOURCE JQY8113A 3-Light Chandelier
Project Source and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Thank you for purchasing this Project Source product. We’ve created these easy-to-follow instructions to ensure you spend your time enjoying the product instead of putting it together. But, if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.
TROUBLESHOOTING|
---|---
|
PROBLEM| POSSIBLE CAUSE| CORRECTIVE ACTION|
Bulb will not light.|
- Bulb is burned out
- Faulty wire connection.
|
- Replace light bulb.
- Check wiring.
|
CARE AND MAINTENANCE|
- Shut off main power before cleaning light with damp cloth or window cleaner. Do not use abrasive cleansers.
WARRANTY
- The manufacturer warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year limited from the date of purchase.
|
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20-30 minutes.
TOOLS REQUIRED (NOT INCLUDED)
FEELING CONFIDENT? START YOUR NEXT PROJECT
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
- Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.
- Account for small parts and destroy packing material, as these may be hazardous to children.
- Use flashlight or alternate light source to light work area during installation.
- Assistance may be required to support fixture during installation.
CAUTION
- Connect fixture to supply wires rated for at least 167˚F.
- Workable for dimming circuits when using appropriate light bulbs with dimmable function.
PACKAGE CONTENTS
HARDWARE CONTENTS
Note: Hardware shown actual size.
INSTALLATION OVERVIEW
Adjust arms of fixture body (I) evenly.
Screw center column (H) onto fixture body (I). 
Unscrew nut (D) from screw collar
loop (C). Unscrew the threaded tube (B) almost out of mounting strip (A) to
get enough length to attach the screw
collar loop (C) and nut (D) on it to hold canopy (E) in place. Note: Do
not install canopy (E) yet.
Attach mounting strip (A) to outlet box (not included) using outlet box screws
(AA).
Unscrew the K/D rings (F) from chain (G).
Adjust chain (G) to desired length. Spread the chain link using standard
pliers (not included) and screw driver (not included) and twist chain link in
opposite direction and remove the extra chain lengths.
Note: Wrap soft cloth (not included) around pliers and screw driver to
protect the chain’s finish.
Weave electrical wires and ground wire up
chain (G), through nut (D), through canopy (E), through the screw collar loop
(C), through threaded tube (B), and into outlet box.
Strip 3/4 in. of insulation from wire end. Twist stripped ends of the white,
ribbed or tinned wire without writing from the fixture evenly against the
white wire from the outlet box. Connect the black, smooth or un-tinned wire
with writing from the fixture to the black wire from the outlet box in the
same manner. Snip ends. Attach copper wire to ground wire. Helpful hint: If
the outlet box doesn’t have a ground wire, you can attach the ground wire from
the fixture directly to the green screw preassembled on the mounting strip
(A).
Attach wire connectors (BB) to ends. Tape wire connectors (BB) and wires
together with electrical tape (not included). Tighten the nut (D) onto screw
collar loop (C) to secure canopy (E) in place. Unscrew socket rings (L),
remove the metal rings (K) from sockets on fixture body (I).
Attach glass shades (J) over the sockets. Place the metal rings (K).
Tighten socket rings (L) with socket ring fastener (CC) as needed. Note: Do
not overtighten. Install light bulb (not included).
Use 60-watt max. standard-base incandescent bulb or CFL/LED equivalent.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>