PHILIPS WT120C G2 MDU CoreLine Waterproof Light User Manual

: June 9, 2024
: Philips

Table of Contents

PHILIPS WT120C G2 MDU CoreLine Waterproof Light
Instruction
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILIPS WT120C G2 MDU CoreLine Waterproof Light

Instruction

Microwave Motion Sensor

Daylight sensor (default disabled)
The sensor can be set to only allow the luminaire to switch on when the ambient lux-level is less than approximately 300[lux]. When set to DISABLE mode, the daylight sensor will switch on the luminaire when motion is detected, regardless of ambient light level
The sensor is designed to connect one load only. Connecting more than one load may damage the sensor.

Detection area (default 100%)
Detection area can be reduced by selecting the combination on the DIP switches to fit precisely each application. Detection radius: 4 – 9 [m] Mounting height up to 4m (*)

Hold time (default 5 min.)
Refers to the time period the lamp remains on no motion detected.

1| 2| | | 3| 4| | | 5| 6| |
---|---|---|---|---|---|---|---|---|---|---|---
ON| ON| <300Lux| | ON| ON| 40%| | ON| ON| 10 n
| | D SABLE| | ON| | 60%| | ON| | 5 n
| (*) Recomended maximum mounting| ON| 80%| | ON| 1 n
9a| height for optimal sensor performance| | 100%| | | 10

The sensor is designed to reliably detect walking people.
Microwave sensors can detect movement behind walls (brick, dry wood, acrylic board, glass, etc.). The detection behind walls can be reduced by choosing a lower sensitivity setting (use Dip switches 3 and 4 to choose a sensitivity lower than 100%).
Other undesired detections can be caused by: Strong electromagnetic fields; heavy vibrations; water running in pipes. Detection area (sensitivity) can be reduced caused by big metal surfaces nearby or water on the ground.

Initialization:
After power on, the sensor will warm up and calibrate the environment for about 120 seconds. In the first 30 seconds, the light will stay on, then it will be off for 90 seconds. After the light has flashed 3 times it operates normally. If there is movement during the calibration period, the off-time will be extended. If the off-time is extended (no flashing occurred) without movement, this indicates that there is too much disturbance in the environment.

SERVICE
Light source (LED) is non-user replaceable. The light source contained in this luminaire shall only be replaced by the manufacturer or his agent or a similar qualified person. Do not touch electronic components! Electronic components maybe under high voltage. Caution, risk of electric shock

A T T E N T I O N
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES

Luminaire has basic insulation between Low Voltage supply and control conductors.
The light source and/or control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Storage, installation, use, operation and maintenance of the products needs to be performed exactly according the instructions in this manual and/or other instructions as may be provided by us to guarantee safe use of the product over its entire lifetime. Failure to adhere to these instructions will invalidate your entitlement to warranty. Bolts with indication of torque strength on the drawing need to be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened again to the required torque specification to assure maximum strength over lifetime.
This product contains a light source of energy efficiency class: see table or label.

All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use.
Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Signify Holding
The Netherlands