iHome iBT245 Dual Alarm Clock with Bluetooth Speaker and USB Charging Instruction Manual
- June 8, 2024
- iHome
Table of Contents
iHome iBT245 Dual Alarm Clock with Bluetooth Speaker and USB Charging
IMPORTANT SAFETY INSTRUCTIONS
- Please heed all warnings, read and follow all instructions and keep these instructions handy for future reference.
- Do not use this product near water.
- Unplug unit and clean only with damp cloth. Stronger cleaning agents, such as Benzene, thinner or similar materials can damage the surface of the unit.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Heat – This product should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this product during lightning storms or when unused for long periods of time.
- Damage Requiring Service – This product should be serviced by qualified service personnel when:
- Plug has been damaged.
- Objects have fallen into or liquid has been spilled into the enclosure.
- The unit has been exposed to rain. The unit has been dropped or the enclosure damaged.
- The unit exhibits a marked change in performance or does not operate normally.
- No naked flame sources, such as lighted candles, should be placed on this product.
- Attention should be drawn to the environmental aspects of battery disposal. Many electronics retailers now recycle batteries and other electronic components at no charge.
- To find a drop-of location near you, visit www.call2recycle.com
- This product is suitable for use in tropical and/or moderate climates
WARNING:
- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- Do not dispose of batteries in the household trash or fire.
- The mains plug of power adaptor is used as the disconnect device, it shall remain readily operable.
- Do not ingest the battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Dual Alarm Clock
(Bluetooth Speaker and USB Charging)
- POWER
- Press to turn ON/OFF
- TIME SET
- Press & Hold to Set Clock
- Use +/- to select 12/24 hour display and press Time Set to confirm
- Use +/- to set hour and press
- Time Set to confirm
- Use +/- to set minute and press Time Set to confirm
- Continue steps to set year, month, and date, and press
- ALARMS 1 & 2
- Press & Hold to Set Alarm
- Use +/- to select hour and press
- Alarm Set to confirm
- Use +/- to select minute and press Alarm Set to confirm
- Use +/- to select schedule (7 days, weekdays, or weekends only) and press Alarm Set to confirm
- Press and release to arm/disarm alarm
- When alarm is sounding, press Alarm Set to disarm and reset for next day
- SET
- Press to decrease/increase settings
- PLAY/PAUSE
- Press to Play/Pause Bluetooth audio
- SNOOZE/DIMMER
- Press to Snooze Alarm
- Press & Hold to Adjust Snooze
- Duration (adjust with +/- and press Snooze to confirm)
- Press to Adjust Display Brightness (cycle through Hi, 3, 2, Low, and OFF)
- BLUETOOTH MODE
- Press & Hold to Enter Pairing Mode. ‘PAIR’ will appear on the display.
- Select ‘iHome iBT245’ on your Bluetooth device to connect.
- The Bluetooth indicator will appear on the display when connected.
- SLEEP MODE
- Press & Hold to Set Timer
- Press repeatedly to cycle through schedule: 120 min, 90 min, 60 min, 30 min, 15 min, or OFF
- The Sleep Mode indicator will appear on the display when active.
REAR PANEL
BACKUP BATTERY COMPARTMENT
- Make sure the AC adapter is connected, or you will lose your clock settings during battery replacement.
- Use a Phillips screwdriver to unscrew the battery compartment door.
- Remove the exhausted battery and insert a new CR2032 battery. Replace the compartment door. Do not overtighten the screw.
DISPLAY ICONS
ISED Information
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The device comply with ISED RF exposure requirement, users can obtain Canadian information on RF exposure and compliance. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment of and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.