FLAMMA FV04 Harmony Vocal Processor Owner’s Manual

: June 8, 2024
: FLAMMA

Table of Contents

FLAMMA FV04 Harmony Vocal Processor
Precautions
Important Safety Instructions
FCC certification
Main Feature
Layout
Instructions
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLAMMA FV04 Harmony Vocal Processor

Precautions

Please read carefully before proceeding

Power Supply

Please use power supply with ９V and at least 150mA current value for the unit. Incorrect power suuply may cause short-circuit and damage.
Please turn off the power supply if the device is not used for long period.

Important Safety Instructions

Read these instructions
Keep these instructions
Heed all warnings
Follow all instructions
Do not use this apparatus near water
Clean only with a dry cloth
Do not install near any ventilation openings. Install in accordance with the manufacturer’s instructions
Do not install near any heat sources such as radiators, heat registers, stoves or other apparati (including amplifiers)that produce heat
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade of the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point

FCC certification

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation

Main Feature

12 pitches with 11 different harmony mode
Dedicated reverb designed for vocal
Support Guitar in with individual guitar reverb effect
Support 48V phantom power
Can be used as a microphone amplifier or a traditional stompbox
Two different output modes for mixed signal or individual signal from guitar and microphone

Layout

$FLAMMA-FV04-Harmony-Vocal-Processor-FIG- $1$$

MODE ：11 different harmony mode
KEY：Scale section
LEVEL：Harmony volume control/vocal or guitar reverb volume control
SHARP LED button：Semitone/vocal tone mode
FOOTSWITCH : On/off of the pedal
GUITAR IN：: Guitar signal input
GUITAR OUT：Guitar signal out put
MIC：Microphone input
GAIN ： Microphone gain level adjustment
LINEIN : Linesignal on/off
48V : On/off of 48V phantom power
XLROUT : Balanced output
LIFT /GND: : Grounding switch
DCIN:Connect to power supply

Instructions

Select different keynote
Select a correct keynote can help to get accuracy harmony effect. FV04 provide 12 different keynotes.

Rotate the KEY to select between C, D, E, F, G, A, B scale
Press the SHARP to get higher semitone for Db, Eb, F#, Ab, Bb

$FLAMMA-FV04-Harmony-Vocal-Processor-FIG- $2$$

Select major/minor scale

FV04 provides major and minor scale selection. Press the SHARP twice quickly to select minor scale of current keynote, the SHARP button will keep blinking; Then press the SHARP twice again quickly to be back to major scale, the SHARP button will stop blinking.

Select harmony mode

FV04 provide 11 different harmony mode

For example, when it is in C keynot

Reverb effect

FV04 has individual reverb effect for vocal and guitar.
Vocal reverb:Press and hold the SHARP button while rotating the LEVEL knob to adjust the reverb effect
Guitar reverb:Press and hold the footswitch to enter hidden mode, footswitch LED will turn yellow, rotate the LEVEL knob to adjust the reverb effect.

TONE mode of vocal

Press and hold the footswitch to enter hidden mode. Press the SHARP to switch between three different vocal tone mode, The LED of SHARP will show currently selected mode
Normal (LED off); Warm (Red LED); Bright (Blue LED)
Press and hold the footswitch again to quit hidden mode. SHARP LED will show as before.

Footswitch mode

When the FV04 is off, press the footswitch to turn on both harmony and reverb effects the footswitch LED will stay green.
When the FV04 is on, press the footswitch twice quickly to turn off both harmony and reverb effects, the footswitch LED will turn off.
Press footswitch once to turn on/off harmony effect. Red footswitch LED for harmony off;

Green footswitch LED for harmony on.

Press and hold the footswitch to enter hidden mode, the footswitch LED will turn yellow; Press and hold the footswitch

Line in mode

Toggle the LINE IN switch to turn on the line in mode. When it is on, user can connect microphone amplifier to the MIC IN jack, or connect other different FV series pedals.

Output mode

Press and hold the footswitch while power on FV04 to switch between individual output mode and mixed output mode, the TONE button and footswitch LED will blink a while then turn off. The color of TONE button and footswitch LED will indicate the current mode. Blue for individual mode; red for mixed mode.

Individual mode

Guitar signal will only go out from GUITAR OUT; microphone signal will only go out from XLR OUT.

Mixed mode

Guitar and microphone signal will go out from both GUITAR OUT and XLR OUT.