FLAMMA FV03 Voice Changing Sounds Owner’s Manual

June 5, 2024
FLAMMA

FLAMMA FV03 Voice Changing

 **Sounds Owner's Manual**

www.flammainnovation.com

Precautions

Please read carefully before proceeding

Power Supply

Please connect the designated adapter to an AC outlet of the correct voltage, Please be sure  the adapter supplies DC 9v 500mA ,center negative . Unplug the adapter when not in use or during electrical storms

Important Safety Instructions

  1. Read these instructions
  2. Keep these instructions
  3. Heed all warnings
  4. Follow all instructions
  5. Do not use this apparatus near water
  6. Clean only with a dry cloth
  7. Do not install near any ventilation openings. Install in accordance with the manufacturers instructions
  8. Do not install near any heat sources such as radiators, heat registers, stoves or other  apparati (including amplifiers) that produce heat
  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug  has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade of the third prong are provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet
  10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point.

FCC certification

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference
  • This device must accept any interference received, including interference that may cause undesired operation.

Main Feature

  1. Rich reverb effects for polishing up vocals
  2. Choose between 6 special voice-altering effects
  3. Includes guitar input with optional guitar reverb effects
  4. Support 48V phantom power
  5. Line in function supports signal from microphone amplifier or FV series pedals
  6. Two different output modes for mixed signal or individual signal from guitar and microphone

Lay out

  1. REVERB: Reverb effect control
  2. MODE: Switch between different voice effect modes
  3. MIX: Mix rate of dry signal and voice changer signal
  4. TONE LED: Press to select tone mode of microphone
  5. Footswitch: Switch pedal on/off or control other functions
  6. GUITAR IN: Guitar signal input jack
  7. GUITAR OUT: Guitar signal output jack
  8. MIC: Microphone signal input jack
  9. GAIN: Microphone signal input gain level
  10. LINE IN: Line signal switch
  11. 48V: Phantom power switch
  12. XLR OUT: Balanced XLR output jack
  13. LIFT/GND: Balanced output grounding switch
  14. DC IN: Connect 9v 500mA power supply

Instructions

  1. Reverb
    FV03 has three reverb effects. You can adjust the volume level of those effects by rotating the REVERB to the relevant position. (RM: Room reverb, HL: Hall reverb, PL: Plate reverb) Press and hold the footswitch to enter hidden mode. The footswitch LED will turn YELLOW. In this mode, you can adjust the guitar reverb using the REVERB knob.

  2. Voice Tone Mode
    Press the TONE button to switch between different voice tone profiles. The color of the TONE LED indicates the selected mode.
    (Off: Normal, RED: Warm mode, BLUE: Bright mode)

  3. Footswitch
    The FV03 footswitch is a little different from traditional pedals.
    When the pedal is off, press the footswitch to turn on the voice and reverb effects. The footswitch LED will turn GREEN.
    Press the footswitch again to turn off the voice-altering effects. The footswitch LED will turn RED.
    Press and hold the footswitch to enter the hidden menu. The footswitch LED will turn YELLOW.
    You can adjust the guitar reverb effects from this menu. Press and hold the footswitch again to go back to the previous mode.
    When any effect is on, you can press the footswitch twice quickly to turn it off. The footswitch LED  will turn off indicating the pedal is off.

  4. Line in
    Turn on the Line In function for connecting to an external microphone amplifier via MIC IN or to  connect to other FV series effect pedals.

  5. Output mode
    Individual mode: In this mode, the guitar signal will be sent via the GUITAR OUT only. The MIC signal will be sent through the XLR OUT only.
    Mix mode: In this mode, the guitar signal and MIC signal will be mixed and sent via both GUITAR
    OUT and XLR OUT.
    Switching mode: Unplug the power supply. Press and hold the footswitch while powering on the  pedal. The TONE LED and footswitch LED will blink red to indicate that the mode has changed.

Effect List

Specifications

GUITAR IN: 1/4” mono audio jack (impedance value: 1M ohms)
GUITAR OUT: 1/4” mono audio jack (impedance value: 100 ohms)
Mic: XLR balanced input jack (impedance value: 2.14k ohms)
XLR OUTPUT: XLR balanced output jack (impedance value: 300 ohms)
Power requirements: AC adapter 9V DC
Current Draw: 500mA
Dimension: 86.6x125x60mm
Weight: 0.371kg
Freq: 20 Hz-20K Hz
Accessories: Safety Instruction & Warranty Card Sticker quick guide

www.flammainnovation.com
Shenzhen Flamma Innovation Co., Ltd
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals