elk Home 18680/1 Lamps and Lighting Hamy 5 Inch Wide 1-Light Sconce User Manual

: June 8, 2024
: elk HOME

Table of Contents

Introduction
- Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elk Home 18680/1 Lamps and Lighting Hamy 5 Inch Wide 1-Light Sconce User Manual

Introduction

WARNING: DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
WARNING: This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications.
If you are not familiar with code requirements, installation by a certified electrician is recommended.
Before assembly, remove all parts and part packages from box.
If anything is missing, please contact the retailer from which the product was purchased.

Carefully pull house wires out of junction box so they are easily accessible during installation.
Position mounting bracket (A) so the head of ground screw is facing outward.
The tabs on mounting bracket (A) should be at the top and bottom and facing outward.
Carefully pull house wires through hole in center of mounting bracket (A).
Align holes in mounting bracket (A) with each hole in junction box. Mounting bracket (A) should be level.
Thread each junction box screw (B) into holes in mounting bracket (A) and into holes in junction box.
Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
CAUTION: Make sure house wires are pulled completely through hole in mounting bracket.
DO NOT pinch wires between mounting bracket and wall.
Strip 3/4” of insulation from ends of fixture wires.
Slightly loosen ground screw on mounting bracket (A). Do not completely remove ground screw.
Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire.
Twist end of fixture ground wire and end of house ground wire together.
Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C).
Reference chart below for correct wire connections.

Connect Supply (House) Ground Copper Wire to:

Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.

Assembly Instruction

Twist end of house lead wire (black) and end of fixture lead wire together.
Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C).
Twist end of house neutral wire (white) and end of fixture neutral wire together.
Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C).
Reference chart to the right for correct wire connections.
Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
Carefully push all wires and wire nuts into junction box.
Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
---|---
Black Wire or,| White Wire or,
Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
No printed words on wire insulation or,| Printed words on wire insulation or,
Insulated Wire (other than green) with Copper Conductor.| Insulated Wire (other than green) with Silver Conductor.
When parallel wire (SPT 1 & SPT 2) is used:
The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.

Assembly Instruction

Place backplate (D) over mounting bracket (A).
Align holes in top and bottom of backplate (D) with holes in each tab of mounting bracket (A).
Screw one fixture mounting screw (E) into hole in top and bottom of backplate (D) and into holes in each tab of mounting bracket (A).
Tighten fixture mounting screws (E) to secure fixture to wall.
Raise shade (K) up to fixture. Pass hole in top of shade (K) over socket. Thread socket ring (L) onto socket. Tighten socket ring (L) to secure shade (K) in place.
Screw recommended bulb (E26 Edison bulb type, not included) into socket. Verify correct bulb wattage marked on socket of fixture.
WARNING: DO NOT exceed maximum bulb wattage.