AJAX Socket Wireless Indoor Smart Plug User Manual
- June 8, 2024
- ajax
Table of Contents
AJAX Socket Wireless Indoor Smart Plug
Socket is a wireless indoor smart plug with the power-consumption meter
for indoor use.
Designed as a European plug adapter (Schuko type F), Socket controls the power
supply of electrical appliances with a load of up to 2.5 kW.
Socket indicates the load level and is protected from overload.
Connecting to the Ajax security system via a secured Jeweller radio protocol,
the device supports communication at a distance of up to 1,000 m in line of
sight.
Socket operates with Ajax hubs only and does not support connecting via Oxbridge Plus or uart Bridge integration modules.
Use scenarios to program actions of automation devices (Relay, Wall Switch or Socket) in response to an alarm, Button press or a schedule. A scenario can be created remotely in the Ajax app.
How to create and configure a scenario in the Ajax security system
Buy smart plug Socket
Functional Elements
- Two-pin socket
- LED border
- QR Code
- Two-pin plug
Operating Principle
Socket switches on/off the 230 V power supply, opening one pole by the user
command in the Ajax app or automatically according to a scenario, Button
press, a schedule.
Socket is protected against voltage overload ( exceeding the range of 184-253
V) or overcurrent (exceeding 11 A).
In case of overload, the power supply switches off, resuming automatically
when voltage restored to normal values.
In case of overcurrent, the power supply switches off automatically, but can
only be restored manually by the user command in the Ajax app.
Socket with firmware version 5.54.1.0 and higher can operate in pulse or
biostable mode.
With this firmware version you can also select the relay contact status:
- Normally closed – Socket stops supplying power when activated, and resumes when turned off.
- Normally open – Socket supplies power when activated, and stops feeding when turned off.
Socket with firmware version below 5.54.1.0 only works in bistability mode with a normally open contact.
How to find out the firmware version of the device?
In the app, users can check the power or amount of energy consumed by
electrical appliances connected via Socket.
At low loads (up to 25 W), current and power consumption indications may be displayed incorrectly due to hardware limitations.
Connecting
Before connecting the device
- Switch on the hub and check its Internet connection {the logo glows white or green).
- Install the Ajax app. Create the account, add the hub to the app, and create at least one room.
- Make sure that the hub is not armed, and it does not update by checking its status in the Ajax app.
To pair Socket with the hub
-
Click Add device in the Ajax app.
-
Name the device, scan it, or enter the QR code manually (located on the case and packaging), select the room.
-
Plug the Socket into a power outlet and wait 30 seconds – the LED frame will flash green.
-
Click Add – the countdown will begin.
-
Socket will appear in the list of hub devices.
The device statuses update depends on the ping interval set in the hub
settings.
The default value is 36 seconds.
If the device failed to pair, wait 30 seconds and then retry.
For detection and pairing to occur, the device should be located in the
coverage area of the hub’s wireless network (at the same object).
A connection request is transmitted only at the moment of switching on the
device.
When pairing the hub with the smart plug that was previously paired with frame
continuously blinks green.
If the device has not been correctly unpaired, do the following to connect it to the new hub:
- Make sure that Socket is outside the coverage area of the former hub’s wireless network (the indicator of the communication level between the device and the hub in the app is crossed out).
- Select the hub with which you want to pair Socket.
- Click Add Device.
- Name the device, scan or enter the QR code manually (located on the case and packaging), select the room.
- Click Add – the countdown will begin.
- During the countdown, for a few seconds, give Socket at least 25 W load (by connecting and disconnecting a working kettle or lamp).
- Socket will appear in the list of hub devices.
Socket can be connected to one hub only.
States
- Devices
- Socket
| Parameter | Value |
|---|---|
| Jeweller Signal Strength | Signal strength between the hub and the Socket |
| Connection | Connection status between the hub and the Socket |
| Routed Through ReX | Displays the status of using the ReX range extender |
| Current protection | Indicates whether the overcurrent protection is enabled |
| --- | --- |
| Voltage protection | Indicates whether the overvoltage protection is enabled |
| Power | Current consumption in W |
| Electric Energy Consumed | The electric power consumed by the device connected |
to the Socket.
The counter is reset when the Socket lose the power
Temporary Deactivation| Displays the status of the device: active or
completely disabled by the user
Firmware| Device firmware version
Device ID| Device identifier
Settings
- Devices
- Socket
- Settings@
| Setting | Value |
|---|---|
| First field | Device name, can be edited |
| Room | Selecting the virtual room to which the device is assigned |
| Mode | Selecting Socket operation mode: |
- Pulse – when activated, Socket generates a pulse of a given duration
- Biostable – Socket, when activated, changes the state of contacts to the opposite
Contact status|
- Normally closed
- Normally open
---|---
Pulse duration| Selecting the pulse duration in the pulse mode: From 0.5 to
255 seconds
Overcurrent Protection| If enabled, power supply switches off if the current
load exceeds 11A, if disabled the threshold is 16A (or 13A for 5 seconds)
Overvoltage protection| If enabled, power supply switches off in case of a
voltage surge beyond the range of 184 – 253 V
Indication| The option of disabling the LED frame of the device
LED Brightness| The option of adjusting the brightness of the LED frame of the
device (high or low)
Scenarios| Opens the menu for creating and configuring scenarios
Learn more
Jeweller Signal Strength Test| Switches the device to the signal strength test
mode
User Guide| Opens the Socket User Guide
Temporary Deactivation| Allows the user to deactivate the device without
removing it from the system. The device will not execute system commands and
participate in automation scenarios. All notifications and alarms of the
device will be ignored
Please note that deactivated device will save it’s current state (active or
inactive)
Unpair Device| Disconnects the device from the hub and deletes its settings
Socket informs the user of the power level consumed by connected appliances using the LED.
If the load is more than 3 kW (purple), the current protection activates.
| Load level | Indication |
|---|---|
| No power on the Socket | Don’t have any indication |
| Socket turned off | Blue |
| Socket turned on, no load | Green |
| ~550W | Yellow |
| ~1250 W | Orange |
| ~2000W | Red |
| ~2500 W | Dark red |
| ~3000 W | Purple |
| One or more types of protection triggered | Smoothly lights up and goes out red |
The Ajax security system allows conducting tests for checking the
functionality of connected devices.
The tests do not start immediately but within a period of 36 seconds when
using default settings.
The test time start depends on the settings of the detector ping interval (the
“Jeweller” menu in the hub settings).
Jeweller Signal Strength Test
Installation of the Device
The location of Socket depends on its remoteness from the hub, and obstacles hindering the radio signal transmission: walls, floors, large objects inside the room.
Do not install the device near sources of magnetic fields (magnets, magnetized objects, wireless chargers, etc.) and inside rooms with temperature and humidity outside the permissible limits!
Check the Jeweller signal level at the installation location. If the signal
level is low ( one bar), we cannot guarantee the stable operation of the
device.
If the device has a low or unstable signal strength, use a ReX radio signal
range extender.
Socket is designed to connect to a European two-pin socket (Schuko type F).
Maintenance
The device does not require maintenance.
In case of using inductive or capacitance load, the maximum switched current is reduced to 8 A at 230 V AC!
Compliance with standards
Complete Set
- Socket
- Quick Start Guide
Warranty
Warranty for the “AJAX SYSTEMS MANUFACTURING” LIMITED LIABILITY COMPANY
products is valid for 2 years after the purchase.
If the device does not work correctly, you should first contact the support
service-in half of the cases, technical issues can be solved remotely!
The full text of the warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>