WORX WA7160 Makerx Control Hub Instruction Manual

: June 8, 2024
: Worx

Table of Contents

WORX WA7160 Makerx Control Hub
PRODUCT SAFETY
SYMBOLS
COMPONENT LIST
OPERATING INSTRUCTIONS
MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WORX WA7160 Makerx Control Hub

PRODUCT SAFETY

Save all warnings and instructions for future reference. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR CHARGER

Before charging, read the instructions.
Do not use chargers for works other than those for which they are designed.
The charging device must be protected from moisture.
Do not use the charging device outdoors.
Do not open the unit and keep it out of the reach of children.
Ensure that the connection between the charger and your equipment is correctly positioned.
Keep charger’s slots free of foreign objects and protect against dirt and humidity. Store in a dry and frost-free place.
When charging your equipment, ensure that the charger is in a well-ventilated area and away from inflammable materials.
Ensure that your equipment and charger are not left unsupervised during charging.
Longer life and better performance can be obtained if your equipment is charged when the air temperature is between 15°C and 25°C.
Do not charge your equipment in air temperatures below 0°C, or above 45°C.
Disconnect from your equipment when not charging or the charging is over.

20V Hub/HubX is specially designed to work with 20V MakerX series tools BELOW, so do not attempt to use any other devices

Category	Model
20V Cordless Rotary Tool	WX739 WX739.X
20V Cordless Angle Grinder	WX741 WX741.X
20V Cordless Air Brush	WX742 WX742.X
20V Cordless Mini Heat Gun	WX743 WX743.X
20V Cordless Wood & Metal Crafter	WX744 WX744.X
20V Cordless Rotary Cutter	WX745 WX745.X
---	---
20V Cordless Glue Gun	WX746 WX746.X
20V Cordless Mini Blower	WX747 WX747.X

SAFETY WARNINGS FOR BATTERY PACK

Do not dismantle, open or shred cells or battery pack.
Do not short-circuit a battery pack
Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
Do not subject battery pack to mechanical shock.
In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
Seek medical advice immediately if a cell or battery pack has been swallowed.
Keep battery pack clean and dry.
Wipe the battery pack terminals with a clean dry cloth if they become dirty.
Battery pack needs to be charged before use. Always refer to this instruction and use the correct charging procedure.
Do not maintain battery pack on charge when not in use.
After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.
Recharge only with the charger specified by Worx. Do not use any charger other than that specifically provided for use with the equipment.
Do not use any battery pack which is not designed for use with the equipment.
Keep battery pack out of the reach of children.
Retain the original product literature for future reference.
Remove the battery from the equipment when not in use.
Dispose of properly.
Do not mix cells of different manufacture, capacity, size or type within a device.
Do not remove battery pack from its original packaging until required for use.

SYMBOLS

COMPONENT LIST

WORX WA7160 Makerx Control Hub - 2

ON/OFF SWITCH
USB PORT *
SPEED CONTROL BUTTON
BELT CLIP *
FLEXIBLE POWER CORD
POWER CONNECTOR

TECHNICAL DATA

| WA7160| WA7161
---|---|---
Output| 20 V 10 A, Max.| Output: 20 V 10 A, Max.

Or Output: 5 V 2 A (USB port)

Input| 20 V 10 A, Max.
Battery type| Lithium battery
Battery pack voltage| 20 V
Weight| 80 g
Category| Model| Capacity
---|---|---

20V Battery

OPERATING INSTRUCTIONS

ASSEMBLY

Insert battery pack into the hub.
Connect the hub and MakerX series tools.

WARNING : Before operation, make sure the speed control button on the hub is at the“Min“ position.

OPERATION

Confirm the speed control button is set to “Min”. Grasp the tool by the grip.Press the on/off switch to start.
Adjust the variable speed as needed for the tool and application.
Press the on/off switch on the hub to turn off after use.
With a USB port (output: 5 V, 2 A) (only for specific models), your hub can be connected to a LED light, or used to charge small electronics or tools such as cell phones, cordless screwdrivers, tablets, etc..

MAINTENANCE

There are no repairable parts in your hub.
For adjustment, repair or maintenance, please leave it to the professional. Do not try to repair the hub yourself.
Your hub does not need to be lubricated or otherwise maintained. Don’t clean the hub with water or chemical cleaning agent, just wipe it with a dry cloth. Store in a dry environment.

ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authorities or retailer for recycling advice

After-sales Service and Application

At www.worx.com you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: 0345 202 9679
E-Mail: customerservices@worxtools.com

DECLARATION OF CONFORMITY