UniGuard BT02 Wireless Control Smart Turning Signal Device Instruction Manual
- June 8, 2024
- UniGuard
Table of Contents
UniGuard BT02 Wireless Control Smart Turning Signal Device Instruction Manual
Product introduction
You can remotely control the smart turning signal device, delivering
left/right turning, parking and brake light warnings to the vehicles driving
behind while keeping your outdoor riding safe. Moreover, you can check the
location through GPS positioning, prevent theft, find vehicles, and provide
security for your outdoor riding.
- Turning Light Device Product Appearance Diagram
- Red Waring Light
- Yellow Left Turning Light
- Yellow Right Turning Light
- Power Button ( Function Button )
- Micro USB Charging Port
2. Remote Controller Appearance Diagram
Smart Turning Signal Device Installation Communication SIM Card Installation Method
Note: The card must be inserted in place, it means it is well installed when you hear the sound of the buckle faintly.
Remote Controller Pairing
- Hold pressing the power button of turning light device and remote controller until the red light flashes 3 times on turning device. indicates the pairing is done. As shown in Figure A.
Remote Controller Installation
1.Take out the remote control , install it on the bicycle bar, tighten it with a screwdriver. The remote control is suitable for the size of the handle: 15-28mm.
1. As shown in Figure C on the right, put the installed turning device on the bicycle seat tube and lock it with screws. If it is too loose, it is recommended to add rubber gaskets. ( Suitable seat tube size for turning device: 25-32mm )
Switch Functions Introduction
The Switch on Turning Light Device
- Left Turn Button: Press the left turn button on the remote controller, the left turning indicator flashes; press this button again, the steering function is turned off; if the left turn button is not turned off in time, the turn indicator will automatically cancel the steering status display within 1 minute.
- Right Turning Button: The principle is the same as the left turning button.
- Brake Button: Press the brake button to turn on the brake state, and release the brake button to turn off the brake state. At the same time of braking, the LED lights are highlighted to remind the car behind to pay attention.
Product Parameters
Product Size: 111.43033,8mm
Turning Device Weight: 125g
Communication Band: LTE/4G LTE-FDD:B1/B3/B5/B8
LTE-TDD: B34/B38/B39/B40/B41
SIM Card：Standard SIM Card
Positioning Module Brand/Chip Model：ZKMicro
Positioning Method: Beidou+GPS
Waterproof Level: IPX4
Charging Input: DC 5V 1A
Luminance of Red Warning Light: 85LM
Turning Device Battery Capacity: 2400mAh
Turning Device Battery Life: Approx. 7 hours With Light is always on
Remote Controller Battery Capacity: 180mAh
Remote Controller Battery Life: No less than 2 months
Remote Controller Charging Time: Around 1-2 hours, red light on while
charging, and green light on while being fully charged.
Turning Device Charging Time: 2-3 hours, red light on while charging, and
green light on while being fully charged.
Turning Device Standby Time: when the turning device is powered on but no
lights on, the standby time can be about 1 month; when the turning device is
off, the standby time can reach more than one year.
Product List
Smart Turning Signal Device
Remote Controller
Fixing Bracket of Turning Device
Rubber Gaskets
Type-C & Micro 2 in 1 USB Charging Cable
User Manual
Fixing Screw & Cap of Turning Device
Fixing Screw & Cap of Remote Controller
Warnings:
- Do not disassemble the device by yourself. There are fragile stickers on the internal connection of the product. Once it is damaged, it will not be guaranteed.
- When this product is not used for a long time, please charge it at least once within three months, otherwise the battery may not be fully charged.
- The waterproof level of this product is IPX4, which can be used in light rain, but please do not soak the product in water.
This card is the basic certificate of warranty, please fill in this card carefully and keep it properly.
SMS configure command:
