UniGuard Technology Limited UT07 Series OBD GPS Tracker User Manual
- June 16, 2024
- UniGuard Technology Limited
Table of Contents
UniGuard Technology Limited UT07 Series OBD GPS Tracker
Product Information
Specifications
- Product Name: UT07/UT07L OBD GPS Tracker
- Manufacturer: UniGuard Technology Limited
- Version: V1.0
- Functions: Location inquiry, geo-fence, over-speed alarm, power-off alarm, historical route playback, voice monitoring
Product Accessories and LED Light Status
Accessories:
- Standard: device, user manual
Device LED Light Status:
| LED Light | Status | Meaning |
|---|---|---|
| Yellow LED (GSM signal status) | Flash every 2 seconds | GSM initialization |
| Off | GSM sleep/power off | |
| Blue LED (GPS signal status) | Flash every 2 seconds | GPS signal searching |
| Off | GPS sleep/power off |
Installation Instructions
Preparation before installation:
- Open the box and check whether the device and the accessories are complete, otherwise please contact your dealer.
- SIM card selection: The device works with a Micro SIM card and supports full Netcom band.
- SIM card installation: Insert the SIM card with the corner inside and the chip face to the side with shrapnel, which can help to hold the card.
Note:
- Before installing or removing the SIM card, please switch off the device.
- Activate the GPRS function of the SIM card.
- Activate the caller ID function (activate or not according to the functions you chose).
- If your SIM card requires you to input the SIM PIN, please refer to your mobile phone user manual to turn off the SIM PIN function.
- Please ensure that the SIM card is valid.
SMS Commands and Instructions
Send SMS command from user’s SIM card number to the SIM card number which is inside the GPS device. The commands in the following SMS command list are in English input format, and the letters are case-sensitive according to the instruction requirements.
Common Commands:
| SMS Command | Device Reply |
|---|---|
| Check setup | Version, ID, IP, etc… |
| Set admin number | Admin ok |
| Set new password | Password reset okay. |
| Device restart | CQ OK |
| Restore factory settings | FORMAT OK |
| Revise APN | APN OK |
| Over speed alarm | SETOK: SPEED=90 |
App
Search “GPSPOS” at App Store or “POSGPS” at Google Play to find the app.
FAQ
Q: Where can I find the app for this GPS tracker?
A: You can search “GPSPOS” at App Store or “POSGPS” at Google Play to find the
app.
Thank you very much for using GPS TRACKER, the user manual will guide how to operate this product, please read it carefully before using it in order to get the correct method of operation. If the appearance, color and accessories of this product are modified, please refer to the actual product. The manufacturer is not liable for faults and omissions which in the user manual.
Product Functions & Parameters
Product functions
Location inquiry, geo-fence, over-speed alarm, power-off alarm, historical
route playback,\ voice monitoring
Parameters
- UT07 2G Frequency: 850/900/1800/1900 Mhz;
- UT07L 4G Frequency: LTE FDD: B1/2/3/4/5/7/8/28/66 and 850/900/1800/1900 Mhz;
- Wide voltage input range: 8 – 24V;
- Location time: average warm start:≤3sec(open sky)
- Average cold start:≤35sec(open sky)
- Device dimensions:42mm × 28mm × 17mm;
- Location accuracy:≤10 meters;
- Working Temp:-20℃ – 75℃
- Backup battery: 200mAh
Product Accessories and LED light status
-
Accessories:
Standard: device, user manual -
Device LED light status
-
Yellow LED (GSM signal status)
Light status| Meaning
---|---
Flash every 2 seconds| GSM initialization
on| GPRS normal communication/online
off| GSM sleep/power off -
Blue LED (GPS signal status)
Light status| Meaning
---|---
Flash every 2 seconds| GPS signal searching
on| GPS location finished
off| GPS sleep/power off
Installation instructions
Preparation before installation:
- Open the box and check whether the device and the accessories are complete, otherwise please contact your dealer.
- SIM card selection, the device works with Micro SIM card, and support full Netcom band.
- SIM card installation, SIM card corner inside, chip face to the side with shrapnel, which can help to hold the card.
Note :
- Before installing or removing the SIM card, please switch off the device;
- Should activate the GPRS function of the SIM card
- Should activate the caller ID function; (activate or not according to the functions you chose.)
- If your SIM card required you to input the SIM PIN, please refer to your mobile phone user manual to turn off the SIM PIN function.
- Please ensure that the SIM card is valid.
Installation
Device with standard OBDII socket
SMS commands and instructions:
Send an SMS command from the user’s SIM card number to the SIM card number
inside the GPS device.
The commands in the following SMS command list are in English input format,
and the letters are case-sensitive according to the instruction requirements
| Common commands | SMS command format | Device reply |
|---|---|---|
| Check setup | CXZT | Version, ID, IP, etc… |
| Set admin number | admin123456 15012404563 | Admin ok |
| Set new password | pwd123456 654321 | Password reset okay. |
| Device restart | CQ | CQ OK |
| Restore factory settings | FORMAT | FORMAT OK |
| Revise APN | NAPN=cmnet,, | APN OK |
| Over speed alarm | SZCS#SPEED=120 | SETOK: SPEED=90 |
App
- Search GPSPOS at Appstore
- Search POSGPS at Google Play