Zooz

Zooz Z-Wave Plus Power Switch

SKU: ZEN15

Quickstart

This is a
secure
On/Off Power Switch
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
Please include the Power Switch to your network BEFORE connecting it to the appliance you wish to control.Auto Z-Wave Inclusion:1. Put your Z-Wave controller into inclusion mode2. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller3. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included4. A new on / off device will be recognized by your Z-Wave controllerManual Z-Wave Inclusion:1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller2. Put your Z-Wave controller into inclusion mode3. Press and release the Z-Wave button 3 TIMES QUICKLY4. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included5. A new on / off device will be recognized by your Z-Wave controllerSecure Z-Wave Inclusion:1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller2. Put your Z-Wave controller in secure inclusion modePress and HOLD the Z-Wave button for at least 3 seconds3. The LED indicator will start flashing green, then turn blue (on) or pink (off) once included4. A new secure on / off device will be recognized by your Z-Wave controller

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

PRODUCT FEATURES:Local and Z-Wave wireless control of your favorite home appliances like microwaves and refrigerators.Energy monitoring in live mode or over time (your Z-Wave gateway needs to support this feature).Scene inclusion for custom automation events when included to a Z-Wave gateway controller.On/Off status recovery after power failure.LED indicator to display Z-Wave signal strength and power usage for the connected device.Added security with AES signal encryption (requires a security enabled gateway controller for full functionality).Z-Wave Plus with improved 500 chip for faster and more reliable wireless communication.Built-in range extender.SPECIFICATIONS:Model Number: ZEN15Z-Wave Signal Frequency: 908.42 MHzPower: 120V, 60HzMaximum Load: 15A, 1800W,HPOperating Temperature: 14104 FRange: Up to 130 feet line of sightInstallation and Use: Indoor onlyDimensions: 20 (with cord) x 2.6 x 1.1Weight: 10oz

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

When your networks primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, plug the Power Switch into a grounded receptacle, then PRESS AND HOLD the Z-Wave button for AT LEAST 20 SECONDS. The LED indicator will flash orange and then stay solid orange for 2 seconds to indicate successful reset. The Power Switch will then turn off.NOTE: All previously recorded activity and custom settings will be erased from the devices memory. You may only reset your Power Switch once it has been included to a Z-Wave network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

Please include the Power Switch to your network BEFORE connecting it to the appliance you wish to control.Auto Z-Wave Inclusion:1. Put your Z-Wave controller into inclusion mode2. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller3. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included4. A new on / off device will be recognized by your Z-Wave controllerManual Z-Wave Inclusion:1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller2. Put your Z-Wave controller into inclusion mode3. Press and release the Z-Wave button 3 TIMES QUICKLY4. The LED indicator will start flashing blue, then turn blue (on) or pink (off) once included5. A new on / off device will be recognized by your Z-Wave controllerSecure Z-Wave Inclusion:1. Plug the Power Switch into a grounded receptacle located within direct range from your Z-Wave gateway controller2. Put your Z-Wave controller in secure inclusion modePress and HOLD the Z-Wave button for at least 3 seconds3. The LED indicator will start flashing green, then turn blue (on) or pink (off) once included4. A new secure on / off device will be recognized by your Z-Wave controller

Exclusion

1. Plug the Power Switch into a grounded receptacle located within direct range of your Z-Wave gateway controller2. Put your Z-Wave controller into exclusion mode3. Press and release the Z-Wave button 3 TIMES QUICKLY4. The LED indicator will start flashing orange, then turn blue (on) or pink (off) once excluded5. The Power Switch will disappear from your controller’s device list. The LED indicator will remain solid orange for a few seconds to indicate exclusionIf the first attempt is unsuccessful, please repeat the process following all steps carefully.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 151: Power Report Value Threshold

Choose how you want your Power Switch to report power consumption to your controller and associated devices. The number entered as value corresponds to the number of Watts the appliance needs to go over for the change to be reported. So if 50 Watts are entered by default, the Power Switch will report any change in power usage over 50 Watts (whether its at least 50 Watts more or 50 Watts less compared to previous report).Values: 065535; 0disabled (it will not report power consumption based on value change)
Size: 2 Byte, Default Value: 50

SettingDescription

1 – 65535| Number of Watts the appliance needs to go over for the change to be reported
---|---
0| Disabled

Parameter 152: Power Report Percentage Threshold

Choose how you want your Power Switch to report power consumption to your controller and associated devices by percentage rate. The number entered as value corresponds to the percentage in power usage change the appliance needs to go over for the event to be reported. So if 10% is entered by default, the Power Switch will report any change in power consumption over 10% (whether its at least 10% more or 10% less power consumption compared to previous report).Values: 0255; 0disabled (it will not report power consumption based on percentage change)
Size: 2 Byte, Default Value: 10

SettingDescription

1 – 255| Percentage in power usage change the appliance needs to go over for the event to be reported
---|---
0| Disabled

Parameter 171: Power Report Frequency

Choose how often you want your Power Switch to report power consumption (W) to your controller and associated device. The number entered as value corresponds to the number of seconds. So if 30 is entered by default, the Power Switch will report power consumption every 30 seconds.Values: 52678400; 0disabled (it will not report power consumption)
Size: 4 Byte, Default Value: 30

SettingDescription

Parameter 172: Energy Report Frequency

Choose how often you want your Power Switch to report energy usage (KWH) to your controller and associated device. The number entered as value corresponds to the number of seconds. So if 300 is entered by default, the Power Switch will report energy usage every 300 seconds (5 minutes).Values: 52678400; 0disabled (it will not report energy usage);
Size: 4 Byte, Default Value: 300

SettingDescription

Parameter 173: Voltage Report Frequency

Choose how often you want your Power Switch to report voltage (V) to your controller and associated device. The number entered as value corresponds to the number of seconds.Values: 52678400; 0disabled (defaultit will not report voltage levels)
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 174: Electricity Report Frequency

Choose how often you want your Power Switch to report levels of electrical current (A) to your controller and associated device. The number entered as value corresponds to the number of seconds.Values: 52678400; 0disabled (defaultit will not report electrical current levels)
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 20: Overload Protection

Overload protection will turn the Power Switch relay off once power exceeds 16.5A for over 5 seconds when this setting is enabled. We DO NOT recommend changing this parameters value as it may result in device damage and malfunction.Values: 0Disabled; 1Enabled (default).
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 21: On/Off Status Recovery After Power Failure

Choose the recovery state for your Power Switch if power outage occurs.Values: 0Power Switch remembers the status prior to power outage and turns back to it (default); 1Power Switch automatically turns ON once power is restored (it does not remember the status prior to power outage); 2Power Switch automatically turns OFF once power is restored (it does not remember the status prior to power outage);
Size: 1 Byte, Default Value: 0

SettingDescription

0| Power Switch remembers the status prior to power outage and turns back to it
---|---
1| Power Switch automatically turns ON once power is restored
2| Power Switch automatically turns OFF once power is restored

Parameter 24: On/Off Status Change Notifications

Your Power Switch will automatically send a notification to the controller and other associated devices if its status changes from on to off or the other way round. Choose when you want it to send the report.Values: 0disabled (it will not send status change notifications); 1sends notification if status is changed manually or remotely via Z-Wave (default); 2sends notification ONLY if status is changed manually by pressing and releasing the Z-Wave button on the Power Switch;
Size: 1 Byte, Default Value: 1

SettingDescription

releasing the Z-Wave button on the Power Switch

Parameter 27: LED Indicator Control

You can choose how the LED indicator displays power consumption on the Power SwitchValues: 0LED indicator will display power consumption whenever the device is plugged in (LED stays on at all timesdefault setting); 1LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off (LED indicator will stay off for most of the time).
Size: 1 Byte, Default Value: 0

SettingDescription

0| LED indicator will display power consumption whenever the device is plugged in
---|---
1| LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Basic
• Configuration
• Device Reset Locally
• Firmware Update Md V2
• Manufacturer Specific V2
• Meter V3
• Powerlevel
• Scene Activation
• Scene Actuator Conf
• Security
• Switch All
• Switch Binary
• Version V2
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>