PREMIUM LEVELLA PJE648 Espresso Maker User Manual

PJE648 Espresso Maker
User Manual USER MANUAL
Use and care manual. Important safeguards. This product is for domestic use only.

Please Read and Save this Use and Care Book.

IMPORTANT SAFEGUARDS.

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury, including the following:

• Read all instructions before using your juice extractor
• Before using, place this juice extractor on a stable surface and operate it according to the instructions in this manual. Always use the juice extractor on a dry, leveled surface.
• Always make sure the juice extractor is properly and completely assembled before operating. The unit will not turn on unless properly assembled. Before turning the juicer on, install and make sure that the juicing filter, recollecting ring tray and motor unit are completely assembled in their correct position and there is no forced contact between the juicing filter and clear cover. Place the clear cover on, fasten the handle before tuming the juicer on.
• Before juicing, the motor works in a “running-in” state. There might be a slight smell and noise right after you turn on the appliance. It is very normal. Let the motor run without load for about 10 seconds. After the motor works for some period, the slight smell and noise will disappear.
• DO NOT PUT YOUR FINGERS OR OTHER OBJECTS INTO THE JUICER OPENING WHILE IT IS IN OPERATION. IF FOOD BECOMES LODGED IN THE OPENING, USE FOOD PUSHER OR ANOTHER PIECE OF FRUIT OR VEGETABLE TO PUSH IT DOWN. WHEN THIS METHOD IS NOT POSSIBLE, TURN THE MOTOR OFF, UNPLUG FROM OUTLET AND DISASSEMBLE JUICER TO REMOVE THE REMAINING FOOD.
• Be sure to tum switch to off position “0” (OFF) after each use of your juicer. Make sure the motor stops completely before disassembling. Always tum the juice extractor off first before unplugging it from the outlet.
• During use, make sure excess juice or pulp residue do not accumulate excessively in the juicing filter, recollecting ring or pulp collector container. If any of those are too full, please turn the juicer off, clean up the components, and then resume using the juice extractor.
• Always make sure juicer lid/cover is clamped securely in place before motor is turned on. DO NOT unfasten clamps while juicer is in operation. Avoid contact moving parts. DO NOT touch the small cutting blades located at the base of the stainless steel filter. DO NOT push produce into the feed chute with your fingers. Always use the food pusher provided. DO NOT touch the small cutting blades in the base of the stainless steel filter basket.
• DO NOT use the appliance if the rotating sieve/filter is damaged.
• Do not operate without the pulp collector container in place.
• Never wash the removable components of this juicer in high temperature water. Do not wash the removable components in a dishwasher. Do not boil or steam the removable components of this juicer for disinfection. Wash all removable components by hand.
• Close supervision is necessary when any appliance is used by or near children. Never leave the appliance unattended.
• The small cutting blades located at the base of the stainless steel juicing filter are extremely sharp. Do not attempt to scrub them directly with your hand. In order to avoid danger, place the juicing filter under running water to ease the cleaning process. Using a nylon brush to clean it is recommended. Read cleaning section of this manual.
• This juice extractor is designed for household use only. This appliance should be used for extracting juice from fruit and vegetables such as apples, carrots, cucumber, tomatoes, etc. Do not use it for any other purpose. Any use other than the described in these instructions must be considered improper and may lead to personal injury or material damage.
• DO NOT operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest authorized service center for examination, repair or electrical or mechanical adjustment. In case of a damaged power supply cord and in order to avoid any danger, replacement must be performed by a service center or qualified professional. If the appliance malfunctions, do not attempt to repair it yourself.
• The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury.
• Tum the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord. Do not remove the juicer container until the juice extractor is turned off and the power cord has been pulled out of the power supply.
• DO NOT let cord hang over edge of table or counter as it can be pulled by children or cause entanglements, trips and falls.
• To protect against risk of electrical shock, DO NOT put power cord or motor base in water or any other liquid
• DO NOT use outdoors. Only use it indoors.
• DO NOT let cord touch hot surfaces, including the stove. DO NOT place this appliance on or near a hot gas or electric burner, or where it could touch a heated oven.
• This appliance is designed for short-term operation only. DO NOT operate this appliance continuously for more than 1 minute. Allow it to cool down for 2 minutes afterwards. After 3 such cycles, the unit must be permitted to cool down for 15 minutes before it is switched on again.
• Check that the power supply complies with the rated voltage.
• This appliance is not intended for use by persons(including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
• Never feed food by hand. Always use food pusher.

SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.
If a longer detachable power-supply cord or extension cord is used, the marked electrical rating of the extension cord should be the same as that of your juicer. The extension cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally.
This appliance comes with a thermal resettable fuse feature to prevent damage to the motor in the case of extreme overload. It shuts off the appliance in case of overheating in order to protect the motor. Should the unit shut off unexpectedly, unplug it and let it cool for around 30 to 45 minutes before continuing.

COMPONENTS

1. Food pusher.
2. Clear Cover.
3. Lid.
4. Juicing filter.
5. Filter holder.
6. Juice outlet.
7. Locking clip.
8. Motor Base.
9. Locking recesses.
10. Pulp container.
11. Juicer Container.

The appliance is equipped with a 3-position switch:
O appliance switched off
I slow juice extraction
II fast juice extraction
The slow juicing setting “I” is suitable for soft, juicy fruits or vegetables such as cantaloupes (peeled), tomatoes etc.
For harder fruits or vegetables such as apples, carrots, it is recommended to use the quick juicing setting “II”.

FEATURES

Your juicer features a wide chute and therefore most fruits and vegetables such as small apples, carrots, beets, celery and others will not need to be cut into smaller pieces since most fit in the chute. If using large fruits or vegetables, clean and cut up the fruit or vegetable so that it fits down the chute, remove any stones, pits or cores to prevent damage to the appliance.
This appliance comes with a thermal resettable fuse feature to prevent damage to the motor in the case of extreme overload. It shuts off the appliance in case of overheating in order to protect the motor. Should the unit shut off unexpectedly, unplug it and let it cool for around 30 to 45 minutes before continuing.
DO NOT operate this appliance continuously for more than 1 minute.

INSTRUCTIONS FOR USE
BEFORE USING THE JUICE EXTRACTOR
This juice extractor has a safety device. If the handle (clamp) is not fasten appropriately, the motor will not turn on. This is a safety feature that will ensure the unit will not operate unless the lid is properly locked. Do not attempt to override this safety feature.
Before you start assembling your juice extractor, make sure it is unplugged and it is placed on a dry and leveled surface.
When assembling or disassembling the juice extractor, press the upper part of the feeding chute with your hand, then push on the handle (clamp) to slide it out of the locked position and release it.
Place the recollecting ring tray on top of the motor base.
Place the stainless steel filter basket on top of the recollecting ring tray until it fits the grooves of the motor shaft.
Place the clear cover on top of the recollecting ring tray and stainless steel filter basket. Adjust it until it aligns properly. Place the food pusher into the clear cover guiding the tab through the groove on the clear cover.
Raise the handle (clamp) and place it on the grooves of the locking tabs located on the clear cover. Push to lock it. The juice extractor will not operate unless the handle and lid are properly locked.
Place the pulp collector container by tilting it slightly and sliding it under the clear cover.
Place the juicer container under the spout located on the right hand side of the motor base. Tilt it slightly and slide it into place. The froth separator will allow to serve juice without the foam and the foam caused during juice extraction will remain inside the container.

OPERATING INSTRUCTIONS

Make sure your juice extractor is properly assembled. Please follow the instructions from the section “Before using the juice extractor.” The Button switch must be in the “0” (OFF) position. This juice extractor has a safety device. If the handle (clamp) is not fasten appropriately, the motor will not turn on. This is a safety feature that will ensure the unit will not operate unless the lid is properly locked.
Prepare your fruits and vegetables by washing them thoroughly and peeling off those that need the skin removed. Remove any stones, pits or cores to prevent damage to the appliance. Ensure the juice extractor and its accessories are clean by following the cleaning and maintenance section of this manual.
Place the juicer container under the spout and make sure the pulp collector container is installed before beginning juicing. Do not allow the pulp collector container to overfill as this may cause the unit to stall.
Plug the power cord into an electrical outlet and turn the power on “I.” Let the motor run without load for about 10 seconds.
Once the juicer is on, place the fruits and vegetables on the food chute and use the food pusher slowly to drive them down. In order to extract the maximum amount of juice, it is important to push the food pusher slowly. If you press too hard or too fast, the juicing effect will be reduced.
The slow juicing setting “I” is suitable for soft, juicy fruits or vegetables such as cantaloupes (peeled), tomatoes etc.
For harder fruits or vegetables such as apples, carrots, it is recommended to use the quick juicing setting “II”.
The juice extractor will separate the juice and the pulp in the juicer container and pulp collector container while you are juicing.
NOTE: Both the pulp container collector as well as the juicer container can be emptied during juicing by turning the juice extractor to the off position “0.” Make sure to install both containers back in place before you resume juicing.
NEVER USE HAND OR FINGERS TO PUSH FOOD DOWN THE FOOD CHUTE OR TO CLEAR THE FOOD CHUTE. ALWAYS USE THE FOOD PUSHER PROVIDED.
ATTENTION: Do not operate this appliance continuously for more than 1 minute. Excessive pressure may result in damage to the motor or the filter.
This appliance comes with a thermal resettable fuse feature to prevent damage to the motor in the case of extreme overload. It shuts off the appliance in case of overheating in order to protect the motor. Should the unit shut off unexpectedly, unplug it and let it cool for around 30 to 45 minutes before continuing.
Never allow the pulp container collector to overfill as this may prevent correct operation or damage the juice extractor.
Always remove large pits from fruits such as prunes, nectarine, peach, mango and similar fruits as they can damage the blades and the unit.
Do not place any fruits or vegetables until you turn the juice extractor on. Let the motor run around 10 seconds before you start adding ingredients.
You can use a plastic bag inside the pulp collector container to ease up its cleaning.
Do not use bananas or avocados as they do not contain juice and will clog the unit. You can later use a blender to add them to the juice you extracted from other fruits or vegetables.
The pulp from fruits and vegetables contains high amounts of fiber and cellulose. You can add it to soups, casseroles or to enhance your desserts. It is better to use the pulp the same day you juice to avoid loss vitamins and changes in its consistency.
When processing large quantities of fruit or vegetables, the pulp collector container and juice container should be emptied from time to time as necessary.
Some fruits and vegetables are NOT suitable for juice extracting like: bananas, avocados, figs, rhubarb, cranberries and similar ingredients.
DISASSEMBLING THE JUICE EXTRACTOR
Before cleaning and storing your juice extractor, follow the instructions below to disassemble:
Turn juice extractor to the off position “0” and unplug the power cord from the electrical outlet before removing any of its components. Always wait until the motor has come to a full stop before disassembling the juice extractor.
Remove the juice container and the pulp collector container by tilting them slightly and sliding them.
Unlock the handle (clamp) by moving it to the right and then downwards to release it from the locking tabs on the clear cover.
Remove the clear cover and food pusher.
In order to remove the stainless steel juicing filter, hold it with two hands and then lift it up by applying pressure to left and right alternatively until it is removed. Also, remove the recollecting ring tray by lifting it up.
WARNING: THE STAINLESS STEEL FILTER CONTAINS SMALL SHARP BLADES TO CUT AND PROCESS FRUITS AND VEGETABLES. DO NOT TOUCH BLADES WHEN HANDLING THE FILTER.

CLEANING

After disassembling all removable parts of the juice extractor, wash them by hand with warm soapy water. If the pulp dries out in the pulp collector container, the stainless steel filter or the recollecting ring tray, let them soak in water for approximately 10 minutes before washing them. The stainless steel filter basket contains sham blades. Do not touch them when handling the filter.
Wipe the motor base with a damp cloth. Never immerse it in water or any other liquid.
It is very important to keep the stainless steel filter very clean, free of residues blocking the holes in order to ensure optimal performance. Use a nylon brush to clean it thoroughly (see picture for suggested brush, not included), if necessary. This way you can clean the stainless-steel filter thoroughly without touching the blades with your hand. Never use a harsh cleaning solution, a hard object or a hard brush to clean the components of the juice extractor. If the holes in the mesh remain blocked, soak the filter in hot water with a water solution with 10% lemon juice.

Some fruits or vegetables may stain plastic components if they are in contact for prolonged periods of time. Wash all removable components promptly after each use.
NOTE: DO NOT IMMERSE THE MOTOR BASE IN WATER OR ANY OTHER LIQUID.
The juice extractor should be used often to keep the motor in best condition. If you are not going to use the juice extractor for a long time, store it in a dry and well ventilated place.
Any other servicing should be performed by an authorized service representative.

TROUBLESHOOTING

handle (clamp) may not be locked properly in its position. It must be placed on the grooves of the locking tabs of the clear cover.
Turn off and unplug unit and ensure all parts are assembled correctly
Turn off and unplug unit and check if there are residues blocking the unit
Motor makes loud noises and vibrates| Turn off and unplug unit. Make sure all parts are assembled correctly.
Juicing overripe fruits may produce too much pulp and clog the stainless steel filter. Turn off and unplug unit and clean the filter.
Motor appears to stall when juicing| If pulp builds up under the lid, slow down the juicing process.
Turn off and unplug unit and clean the recollecting ring tray, the stainless steel filter and the clear cover.
Too much pulp builds up on stainless steel filter| Try a slower juicing action by pushing the food pusher down slower. Remove stainless steel filter and clean thoroughly with a nylon brush. Rinse the filter basket with hot water. If the fine mesh holes are blocked, soak the basket in a solution of hot water with 10% lemon juice to unblock the mesh. This will remove excess fiber build up (from fruit or vegetables) that could be reducing the flow of juice.
Juice leaks between the rim of the Juicer and clear cover.| Try a slower juicing action by pushing the food pusher down slower.

Any other servicing should be performed by an authorized service representative.
CUSTOMER SERVICE NUMBER
In the U.S. 1-855-531-4808

Disposal

Devices marked with this symbol must be disposed of separately from your household waste, as they contain valuable materials which can be recycled. Proper disposal protects the environment and human health. Please respect your local regulations.

www.premiumus.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>