Kenmore KLFC015MWD Manual Defrost Chest Freezer User Guide
- June 8, 2024
- Kenmore
Table of Contents
- KLFC015MWD Manual Defrost Chest Freezer
- Important Safety Instructions
- First Steps
- Energy Saving Ideas
- Freezer Use
- Temperature Control
- Special Features
- Care & Cleaning
- Power Failure/ Freezer Failure
- Before You call
- LIMITED WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Use & Care Guide
Chest Freezer
Models: KLFC015MWD-White-1 4.8 cu. ft.
KLFC01 9MWD-White-1 8.5 cu. ft.
KLFC015MWD Manual Defrost Chest Freezer
Record Model/ Serial Numbers
Please read and save these instructions
This Use & Care Guide provides specific operating instructions for your model.
Use your unit only as instructed in this guide. These instructions are not
meant to cover every possible condition and situation that may occur. Common
sense and caution must be practiced when installing, operating, and
maintaining any appliance.
Please record your model and serial numbers below for future reference. This
information is found either on the upper left wall inside the freezer (upright
models) or the left exterior wall (chest models).
Model Number:___
Or____ Serial
Number: ____Purchase
Date:____
IMPORTANT Use only soap and water to clean serial plate.
Important Safety Instructions
Safety Precautions
Do not attempt to install or operate your unit until you have read the safety
precautions in this Use & Care Guide. Safety items throughout this manual are
labeled with a Danger, Warning, or Caution based on the risk type.
Definitions
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
IMPORTANT
Indicates installation, operation, or maintenance informationwhich is
important but not hazard-related.
DANGER
DANGER Risk of fire or explosion. Flammable refrigerant used. To be repaired
only by trained service person-nel. Use only manufacturer-authorized service
parts. Any repair equipment used must be designed for flammable refrigerants.
Follow all manufacturer repair instructions.Do not puncture refrigerant
tubing.
CAUTION
CAUTION Risk of fire or explosion. Dispose of refrigerator properly in
accordance with the applicable federal or local regulations. Flammable
refrigerant used.
CAUTION Risk of fire or explosion due to puncture of refrigerant tubing;
follow handling instructions carefully. Flammable refrigerant used.
WARNING Read all safety instructions before using your new appliance.
For Your Safety
- Do not store or use gasoline or other flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other hazards.
- Do not operate the unit in the presence of explosive fumes.
- Remove and discard any spacers used to secure the basket during shipping. Small objects are a choke hazard to children.
- Remove all staples from the carton. Staples can cause severe cuts and also destroy finishes if they come in contact with other appliances or furniture.
Child Safety
Destroy or recycle the carton, plastic bags, and any exterior wrapping
material immediately after the unit is unpacked. Children should never use
these items to play. Cartons covered with rugs, bedspreads, plastic sheets or
stretch wrap may become airtight chambers and can quickly cause suffocation.
Proper disposal of your appliance
DANGER: Risk of child entrapment! Child entrapment and suffocation are
not problems of the past. Junked or abandoned appliances are still dangerous —
even if they will sit for “just a few days.” If you are getting rid of your
appliance, please follow the instructions below to help prevent accidents.
Before you throw away your old unit:
- Remove lid.
- Leave basket in place within freezer so children may not easily climb inside.
- Have refrigerant removed by a qualified service technician.
IMPORTANT Your old unit may have a cooling system that used CFCs or HCFCs (chlorofluoro-carbons or hydrochlorofluorocarbons). CFCs and HCFCs are believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may cause harm to the environment if released to the atmosphere. If you are throwing away your old unit, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release refrigerant, you may be subject to fines and imprisonment under the provisions of environmental legislation.
WARNING
These guidelines must be followed to ensure that safety mechanisms in this
unit will operate properly.
Electrical Information
- The unit must be plugged into its own dedicated 10 amp, 115 Volt, 60 Hz. AC only electric outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against shock hazards. It must be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Do not use an extension cord or adapter plug.
- Immediately repair or replace any power cord that becomes frayed or damaged.
- Never unplug the appliance by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.
- Unplug the appliance before cleaning and before defrosting to avoid electrical shock.
- Performance may be affected if the voltage varies by 10% or more. Operating the unit with insufficient power can damage the motor. Such damage is not covered under the warranty.
- Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the appliance from being turned off accidentally.
- Avoid connecting unit to a Ground Fault Circuit Interruptor (GFCI).
First Steps
This Use & Care Guide provides specific operating instructions for your model. Use the unit only as instructed in this Use & Care Guide. Before starting the appliance, follow these important first steps.
Installation
- Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.
- For the most efficient operation, the freezer should be located where surrounding temperatures will not exceed 110°F (43°C). Temperatures of 32°F (0°C) and below will NOT affect freezer operation. Additional compressor heaters are not recommended.
- Allow space around the unit for good air circulation. Leave a 4-inch (101.6 mm) space on all sides of the freezer for ad-equate circulation.
Leveling
The freezer must have all bottom corners resting firmly on a solid floor. The
floor must be strong enough to support a fully loaded freezer. If needed, add
metal or wood shims between foot pads and floor.
NOTE It is Very Important for your freezer to be level in order to
function properly. If the freezer is not leveled during installation, the lid
may be misaligned and not close or seal properly, causing cooling, frost, or
moisture problems.
Cleaning
- Wash any removable parts, the freezer interior, and exterior with mild detergent and warm water. Wipe dry. Do not use harsh cleaners on these surfaces.
- Do not use razor blades or other sharp instruments, which can scratch the ap-pliance surface when removing adhesive labels. Any glue left from the tape can be removed with a mixture of warm water and mild detergent, or touch the residue with the sticky side of tape already re-moved. Do not remove the serial plate.
Energy Saving Ideas
- The freezer should be located in the coolest area of the room, away from heat producing appliances or heating ducts, and out of direct sunlight.
- Let hot foods cool to room temperature before placing in the freezer. Overloading the freezer forces the compressor to run longer. Foods that freeze too slowly may lose quality or spoil.
- Be sure to wrap foods properly, and wipe containers dry before placing them in the freezer. This cuts down on frost build-up inside the freezer.
- Freezer shelves should not be lined with aluminum foil, wax paper, or paper toweling. Liners interfere with cold air circulation, making the freezer less efficient.
- Organize and label food to reduce lid openings and extended searches. Remove as many items as needed at one time, and close the lid as soon as possible.
Freezer Use
- To turn the freezer on, plug the power cord into a properly grounded 3 prong electrical outlet. The green Power On light located on the temperature control will illuminate.
- For safe food storage, allow four hours after plugging in for the freezer to cool down completely. The freezer will run continuously for the first several hours. Foods that are already frozen may be placed in the freezer after the first few hours of operation. Unfrozen foods should NOT be loaded into the freezer until the freezer has operated for four hours.
- When loading the freezer, freeze only three pounds of fresh food per cubic foot of freezer space at one time. Distribute packages to be frozen evenly throughout the freezer.
Temperature Control
- The temperature control is located on the front exterior wall. There are 8 positions on the control dial. Position 8 is the coldest and 1 is the least cold setting.
- The Recommended Setting, indicated on the dial midway between postions 4 and 5, should provide optimum frozen food storage within normal operating conditions in most situations.
- If a colder temperature is desired, turn the temperature control knob toward position 8. For a less cold temperature, turn the dial toward 1. Adjust the temperature gradually, in small increments, and allow several hours for temperatures to stabilize between adjustments.
Power On Light
The green Power On light indicates that the freezer is properly connected to
electrical power. If the light goes out, refer to Freezer does not run section
in the Troubleshooting Guide. If the freezer appears to be operating, the
light element may be burned out. To schedule light element replacement, call
1-844-553-6667.
Special Features
Defrost Drain
The defrost drain provides a method of draining the water during defrosting
and cleaning. See Defrosting in Care & Cleaning section.
Freezer Lid Handle
The freezer lid has a built-in handle to aid in the raising and lowering of
the lid.
CAUTION Be careful when the freezer lid is raised that it
doesn’t close on you while you are inserting or removing items.
Storage Basket
The convenient top storage basket for smaller items hangs on the front and
back edges of the freezer compartment.
Care & Cleaning
CAUTION
Damp objects stick to cold metal surfaces. Do not touch interior metal
surfaces with wet or damp hands.
Between Defrostings
To avoid frequent defrosting, occasionally use a plastic scraper to remove
frost. Scrape with a pulling motion. Never use a metal instrument to remove
frost.
CAUTION
Freezer must be unplugged (to avoid electrical hazard) from power source when
defrosting unit.
Defrosting
WARNING
DO NOT use a sharp or metallic instrument to remove frost from the
refrigerator interior, as damage to refrigerant tubing (located behind
interior walls) may occur. Tubing damage may allow flammable refrigerant gas
leakage, which can result in personal injury.
It is important to defrost and clean the freezer when 1/4 to 1/2 inch of frost
has accumulated. Frost may tend to accumulate faster on the upper part of
freezer due to warm, moist air entering when lid is opened. Always unplug
freezer, remove food and leave lid open when defrosting. If frost is soft,
remove by using a plastic scraper (included). If frost is glazed and hard,
place a shallow pan beneath the drain outlet at front of freezer (Fig. 1).
Pull the drain outlet plug forward enough to expose the drain hole in the plug
shaft (Fig. 1). Rotate plug so that hole faces straight down. The arrow on the
plug will also face straight down (Fig. 2).Use a thin bladed tool to
carefully pry up and remove the drain plug inside the freezer (Fig. 4).
Defrost water will drain out through the hole in the outside drain plug (Fig.
3). Check pan occasionally so water does not overflow. Replace the drain plugs
when defrosting and cleaning are completed. If the drain is left open, warm
air may enter the freezer.
Cleaning the Inside
After defrosting, wash inside surfaces of the freezer with a solution of two
tablespoons of baking soda in one quart (1.1 liters) warm water. Rinse and
dry. Wring excess water out of the sponge or cloth when cleaning in the area
of the controls, or any electrical parts. Wash the removable parts and baskets
with the baking soda solution mentioned above, or mild detergent and warm
water.
Rinse and dry. Never use metallic scouring pads, brushes, abrasive cleaners,
or alkaline solutions on any surface. Do not wash removable parts in a
dishwasher.
NOTE If unit is turned off or unplugged for several hours, do not open
freezer lid unnecessarily. This will maintain the coldest temperature inside
and reduce the recovery time to desired temperature once the unit is turned
back on.
Cleaning the Outside
Wash the cabinet with warm water and mild liquid detergent. Rinse well and
wipe dry with a clean soft cloth.
Vacation and Moving Tips
WARNING If leaving the freezer lid open while on vacation, make certain
that children cannot get into the freezer and become entrapped.
Short Vacations: Leave the freezer operating during vacations of less than
three weeks.
Long Vacations: If the freezer will not be used for several months:
- Remove all food and unplug the power cord.
- Clean and dry the interior thoroughly.
- Leave the freezer lid open slightly, blocking it open if necessary, to prevent odor and mold growth. Moving: When moving the freezer, follow these guidelines to prevent damage:
- Disconnect the power cord plug from the wall outlet.
- Remove foods, then defrost, and clean the freezer.
- Secure all loose items such as base panel, baskets, and shelves by taping them securely in place to prevent damage.
- In a moving vehicle, secure freezer in an upright position to prevent movement. Also protect outside of freezer with a blanket, or similar item.
Power Failure/ Freezer Failure
If a power failure occurs, frozen foods will stay frozen for at least 24 hours if the freezer is kept closed. If the power failure continues, pack seven or eight pounds of dry ice into the freezer every 24 hours. Look in the Yellow Pages under Dry Ice, Dairies, or Ice Cream manufacturers for local dry ice suppliers. Always wear gloves and use caution when handling dry ice. If the freezer has stopped operating, see Freezer does not run in the Troubleshooting Guide. If you cannot solve the problem, call an authorized servicer immediately. If the freezer remains off for several hours, follow the directions above for the use of dry ice during a power failure. If necessary, take the food to a local locker plant until the freezer is ready to operate. Look in the Yellow Pages under Frozen Food Locker Plants.
Before You call
TROUBLESHOOTING GUIDE| Before calling for service, review this list. It
may save you time and expense. This list includes common occurrences that are
not the result of defective workmanship or materials in this appliance.
---|---
CONCERN| POTENTIAL CAUSE| COMMON SOLUTION
Freezer does not run.| 1.Freezer is plugged into a circuit that has a ground
fault interrupt.
2.Temperature control is in the OFF position.
3.Freezer may not be plugged in or plug may be loose.
4.House fuse blown or tripped circuit breaker.
5.Power outage.| 1.Use another circuit. If you are unsure about the outlet,
have it checked by a certified electrician.
2.See Setting the Temperature Control Section.
3.Ensure plug is tightly pushed into outlet.
4.Check house fuse or circuit breaker.
5.Check house lights. Call local Electric Company.
Freezer runs too much or too long.| 1.Room or outside weather is hot.
2.Freezer has recently been disconnected for a period of time.
3.Large amounts of warm or hot food have been stored recently.
4.Lid is opened too fre- quently or too long.
5.Lid may be slightly open.
6.Temperature Control is set too low.
7.Freezer gasket is
dirty, worn, cracked, or poorly fitted.| 1.It is normal for the freezer to
work harder under these conditions.
2.It takes 4 hours for the freezer to cool down completely.
3.Warm food will cause freezer to run more until the desired temperature is
reached.
4.Warm air entering the freezer causes it to run more. Open lid less often.
5.See Lid Will Not Close in this Before You Call Section.
6.Turn control knob to a warmer setting. Allow several hours for the
temperature to
stabilize.
7.Clean or change gasket. Leaks in the lid seal will cause freezer to run
longer in order to maintain desired temperature.
Interior Freezer temperature is too cold.| Temperature Control is set too
cold.| Turn the control to a warmer setting. Allow several hours for the
temperature to stabilize.
Interior Freezer temperature is too warm.| 1.Temperature Control is set too
warm.
2.Lid is kept open too long or is opened too frequently.
3.Lid may not be seating properly.
4.Large amounts of warm or hot food may have been stored recently.
5.Freezer has recently been disconnected for a period of time.| 1.Turn control
to a colder setting. Allow
several hours for the temperature to stabilize.
2.Warm air enters the freezer every time the lid is opened. Open the lid less
often.
3.See Lid Will Not Close in this Before You Call section.
4.Wait until the freezer has had a chance to reach its selected temperature.
5.Freezer requires 4 hours to cool down completely.
Freezer external surface
temperature is warm.| The external freezer walls can be as much as 30°F warmer
than room temperature.| This is normal while the compressor works to transfer
heat from inside the freezer cabinet.
Louder sound levels whenever freezer is on.| Modern freezers have increased
storage capacity and more stable temperatures. They require a high efficiency
compressor.| This is normal. When the surrounding noise level is low, you
might hear the compressor running while it cools the interior.
Longer sound
periods when compressor comes on.| Freezer operates at higher pressures
during the start of the ON cycle.| This is normal. Sound will level off or
disappear as freezer continues to run.
Popping or cracking sound when compressor comes on.| Metal parts undergo
expansion and contraction, as in hot water pipes.| This is normal. Sound will
level off or disappear as freezer continues to run.
Bubbling or
gurgling sound, like water boiling.| Refrigerant (used to cool freezer) is
circulating throughout the system.| This is normal.
Vibrating or rattling noise.| 1.Freezer is not level. It rocks on the floor
when it is moved slightly.
2.Floor is uneven or weak. Freezer rocks on floor when it is moved slightly.
3.Freezer is touching the wall.| 1.Level the unit. Refer to Leveling in the
First Steps section of this Use & Care Guide.
2.Ensure floor can adequately support freezer.
3.Move freezer slightly. Refer to Leveling in the First Steps section after
moving if necessary.
Moisture forms on inside freezer
walls.| 1.Weather is hot and humid, which increases internal
rate of frost build-up.
2.Lid may not be seating properly.
3.Lid is kept open too long, or is opened
too frequently.| 1.This is normal.
2.See Lid Will Not Close in this Before You Call section.
3.Open the lid less often.
Moisture forms on outside of freezer.| Lid may not be seat- ing properly,
causing the cold air from inside the freezer to meet warm moist air from
outside.| See Lid Will Not Close in this Before You Call section.
Odors in freezer.| 1.Interior needs to be cleaned.
2.Foods with strong odors are in the freezer.| 1.Clean interior with sponge,
warm water, and baking soda.
2.Cover the food tightly.
Lid will not close.| 1.Freezer is not level. It rocks on the floor when it is
moved slightly.
2.Floor is uneven or weak. Freezer rocks on floor when it is moved slightly.|
1.This condition can force the cabinet out of square and misalign the lid and
lid seal. Refer to Leveling in the First Steps section of this Use & Care
Guide.
2.Refer to Leveling in the First Steps section of this Use & Care Guide.
LIMITED WARRANTY
FOR ONE YEAR from the date of sale this appliance is warranted against defects
in material or workmanship when it is correctly installed, operated and
maintained according to all supplied instructions.
WITH PROOF OF SALE a defective appliance will receive free repair. If the
appliance cannot be repaired, it will replaced free of charge. The Kenmore
brand name is used under license. Direct all claims for warranty service to
844-553-6667
This warranty is void if this appliance is ever used for other than private
household purposes. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Winiadaewoo Electronics America, Inc., Ridgefield Park, NJ 07660
Kenmore and the Kenmore logo are registered trademarks of Transform SR Brands
LLC and are used under license by Winiadaewoo Electronics America,lnc.
Customer Care Hotline
To schedule in-home repair service or order replacement parts
1-844553-6667
www.kenmore.com
Kenmore and the Kenmore logo are registered trademarks of Transform SR Brands
LLC and are used under license by Winiadaewoo Electronics America Inc.,
Ridgefiled Park, NJ 07660
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>